Question about 1996 Hyundai Accent

1 Answer

Clutch will start,,but not go in gear would go in and out not work in am but work in afternoon,,now will not work,,any gues how much to fix thanks mike millmo84@yahoo.com

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

Probably about 1000.00 or higher

Posted on Aug 22, 2008


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was deriving my 88own ford ranger when the line for the hydraulic clutch poped out from the tranny so i shut it off put it in to first gear started it in gear and drove it home with no clutch now its in...


i think this will work, with the clutch perminantly engaged it is difficult to disengage gears, fixing the clutch should make gear chaging better.

Oct 31, 2013 | Cars & Trucks

1 Answer

My shift knob won't move


WITH INFO YOU ARE PROVIDING CLUTCH MIGHT NOT BE COMPLETELY DISENGUAGING CAUSING A STIFF OR DIFFICULT SHIFT. CHECK BY PUTTING VEHICLE ON FLAT GROUND ENGINE OFF. GET INTO 1ST GEAR. THEN PUSH IN CLUTCH AND START CAR WITH BRAKE OFF IF CAR STARTS ROLLING THEN CLUTCVH IS STILL TRYING TO GRAB. THEN ADJUST THE CLUTCH PER VEHICLE SPECS.

Jun 11, 2012 | 2004 Mazda RX-8

1 Answer

1996 Explorer Sport manual transmission will not go into gear at all now. The transmission and clutch have been replaced a couple years back. The clutch has never been satisfactory because it has to be...


if the clutch is hydrolic,sorry,there is really no adjustment. Hydriloc clutch master cylinders can be a ****** to bleed the air out and it could just take an afternoon of you and a buddy bleeding it. And remember, bleeding a clutch is different than bleeding breaks. It is a slow and time consuming process. If the pedal problem has been going on for some miles, you could also have a bad synchroniser in your trans preventing proper engaugement

Sep 13, 2011 | 1996 Ford Explorer

2 Answers

The clutch slips in first gear when it is hot.


You need a new clutch again. Sorry to give ya the bad news. This time make sure they put a new transmission seal in so fluid can not leak onto the clutch plate and ruin it.

Apr 25, 2010 | 1999 Jeep Wrangler

1 Answer

Won't go into gear to drive. may be transmission?


If the clutch has never been changed most likely it is that. The way you can check it is by removing the transmission and looking at the clutch disc. It could be transmission syncros but I am willing to bet you just need a new clutch.

May 24, 2009 | 2001 Kia Sportage

1 Answer

Will drive through flood water cause clutch problem?


as for choking make sure your air filter is not soaked in water, as for your clutch dont see ya water would affect it unless you picked something up in the puddle that got logged in the linkage

Apr 28, 2009 | 2007 Honda Accord Sedan

2 Answers

Clutch


i don't know if you went back to look at my post, but i fixed my car by putting in a new slave and new master cylinder and then tightening up the clutch petal. it does NOT grind anymore! and my baby is like new! it cost me about $90 through napa auto parts. $66 for the master and $16 for the slave and it comes with everything you need. hope this helps you!

Jan 20, 2009 | 1991 Mitsubishi Eclipse

1 Answer

Hard to put car in gear when engine running. If I start the car in gear the clutch still works fine. What could be the problem? thanks


if only some gears are effected, then most lilkley it is worn syncronizers on those gears requiring a tranmission rebuild. if it is on all gears then it is clutch related. the clutch could be dragging slightly, try flushing and bleeding the clutch hydralics

Nov 25, 2008 | Mitsubishi Minivan Cars & Trucks

2 Answers

1996 Geo Metro Clutch won't disengage


Hi,

In all likelihood two (2) possibilities:
  • defective clutch cable (most likely); and/or
  • defective clutch fork (least likely).
Should it be the cable, this might be of help. It is turns out to be the fork, you might need the services of a qualified professional or a dealership.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information. Good luck and kind regards. Thank you for using FixYa.

Nov 10, 2008 | 1996 Geo Metro

Not finding what you are looking for?
1996 Hyundai Accent Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...