Question about 2004 Mazda 3

2 Answers

Broken Plastic underneath car towards front

I drove over something on the highway that cracked the plastic covering that spans from front wheel to front wheel. Is that something I need to have replaced, and what is it called?

Thanks!

Posted by on

  • Moptart Aug 22, 2008

    Yeah,

    Its cracked so bad that we had to remove it! It was scraping the ground. I called Mazda and they said it's 3 separate parts--I was hoping to find the part(s) cheap and have my local service station mechanic put it on. Thanks for your input!

  • Anonymous Oct 18, 2008

    brken plastic plate underneath car toward the front

×

2 Answers

Bueno, se puede reparar con adhesivo especial. Ademas se puede reforzar con laminas de aluminio que dan rigidez a pieza.

Posted on Sep 26, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 71 Answers

Hey

Is it badly cracked? its only to prevent splashes goin up into your engin bay!! if you did a diy repair to keep it up and not hitting the road you should be ok!! i think the name of them is a "splash pan" not to sure.

Damien

Posted on Aug 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Murano. Where is the starter located?


If you stand facing the engine with the hood open. The starter is located on the left side of the engine. It will be difficult to see from the top. But can be seen if you remove the plastic cover on the right front wheel well, or if you were to remove the plastic panel underneath the car. If you stand facing the engine with the hood open. The starter is located on the left side of the engine. It will be difficult to see from the top. But can be seen if you remove the plastic cover on the right front wheel well, or if you were to remove the plastic panel underneath the car.

Jul 21, 2015 | Nissan Cars & Trucks

1 Answer

Renolte megane 2 head light change right headlight


the steering lock needs to be put on full towards the opposite side, if your changing the drivers side put the lock on towards the passengers.


then remove the plastic cover under the wheel arch.


it will reveal another plastic cover which if rubber will just pull off, else twist off.
this will then reveal the bulb, pull out the cable which may need a bit of a jiggle.


the bulb should be held in place by a metal spring clip which needs to be pushed towards the front of the car and then outwards, this should release the bulb.






change the bulb it should be a 477

Jun 18, 2013 | Renault Cars & Trucks

1 Answer

How 2 take airbag off


First, disconnect battery so that air bag can't go off accidentally. Second, look underneath the wheel, and there is a screw underneath, pointing towards the driver, that hold the cover on. Some don't have screws and simply pry off against plastic snaps.

May 04, 2013 | Cars & Trucks

1 Answer

Location fuel filter nissan quest 2000


underneath vehicle towards drivers side about mid way between front and rear wheels.its covered by a plastic cover that is secured by i think 4 ten mm bolts.please let me know if this helped.

Feb 13, 2011 | 2001 Nissan Quest

1 Answer

Hi, I drive a 2004 focus. This morning coming into work out of nowhere i heard a pop and the wipers stopped working. completely. and as i drove on (in the rain) i started hearing like a sliding noise from...


Check the fuse box located underneath the drivers side steering wheel. Flip the fuse box cover lid cover and there will be a diagram. Locate the "Wiper" fuse on the diagram and replace it with the same number fuse. Look underneath your vehicle for any evidence of broken plastic or possibly your CV axle has broken. Check your oil and transmission fluid and make sure they are topped off. Look for any liquid leaking at the bottom of your car.

Nov 11, 2010 | 1995 Honda Accord

1 Answer

Replace headlight bulb on 2003 Mazda6


IS IT XENON? IF XENON TURN OFF IGNITION. 25000V. TURN WHEEL TOWARDS ENGINE ALL THE WAY AND REMOVE TWO PLASTIC SCREWS FROM THE FRONT BUMPER HOLDING PLASTIC UNDER THE MUD GUARD. PULL BACK THE PLASTIC FOR ACESS TO THE HEAD LAMP. REMOVE COVER. TURN IGNITOR, REMOVE HOLDING WIRE AND LAMP.

Nov 07, 2010 | 2003 Mazda Mazda6

1 Answer

My 2007 Sante Fe fog lamp bulb went out and I wasn't able to


Step:
1. Turn tires away from vehicle
2. There is a plastic covering in front of the wheel that usually goes around the wheel well. There are plastic thumb pins on the outer edges of this plastic covering. Remove the thumb pins and this plastic piece will come off.
3. Behind this you will find access to your fog lights.
4. Remove/Replace just like an ordinary head light.

Jul 17, 2009 | Hyundai Santa Fe Cars & Trucks

1 Answer

My 2001 Subaru Outback has a dent underneath the passenger side brake light, the one underneath the right turn signal light. The brake light does not work, but there are no cracks in the outer plastic...


most likely the bulb filiment got broken, replace bulb first if not working then test socket. i believe to replace bulb u access from inside, ask guy at parts store to help you they will usually give advice help

Jul 07, 2009 | 2001 Subaru Outback

1 Answer

Saab 95 Aero


Jack up o/s of car and support on stand
Remove front o/s wheel

remove bottom engine covers from inside o/s wheel arch and also bottom engine cover(plastic)

support engine with jack; remove yolk engine mount ( on belt side)

Put 1/2" extension drive into top of belt tensioner and pull toward engine - you can now put a 3mm drill bit or allen key into hole at side of tensioner to hold in position.

remove serpentine belt

from underneath car, use 8mm ( I think) allen key to remove centre bolt from belt tensioner

It should now come off of the car

fitting is the reverse of the above

hope it helps


Nov 08, 2008 | 1999 Saab 9-5

2 Answers

How do i remove and replace the driver's side mirror?


If the metal pivot arm is not broken you can just replace the glass and plastic housing. To remove the glass you tilt the glass down towards the floor and use a wide plastic or wood bladed object to prise from behind, the glass should pop off from its clips. Remember to catch it if its not damaged. To remove the housing once the glass is out you need to look underneath the mirror unit, there you will find a small plastic bung, gently prise it out and then use a long small flat bladed screwdriver straight up inside the hole and lever towards the front of the car whilst lifting straight up on the plastic housing, this should then lift off. To replace just slot the new housing on and click into place then fit the glass back, remember to connect the wires first if it is a heated glass.
If the metal pivot arm is broken then you will find the remaining screws behind the plastic trim inside the vehicle.

Oct 26, 2008 | 1998 Volkswagen Beetle

Not finding what you are looking for?
2004 Mazda 3 Logo

Related Topics:

350 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...