Question about 2000 Toyota Land Cruiser

2 Answers

1 HD-fte engine

Vehicle cuts out when on long trip or hard driving, code 97 is given on obd. pump and edu has been replaced as well as all wiring been checked

Posted by on

  • Anonymous Dec 13, 2008

    starting problem

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Agree with Chadcrane's suggestion, however will also advise you thoroughly check BOTH batteries for capacity/charge ( My car has two factory fitted batteries).
If any of them is weak, you will face a HARD / No start issue even though it seems the starter is cranking fine.

Posted on Mar 28, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Have seen the relay that powers the ignition control module (igniter module) burn the terminals. Check the relays really well. the module is a little less than $450 or so. So be sure the power supply to and from relay is good before condemning the module. The relay may also be worn out.

Posted on Aug 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2000 Chrysler town and country van that as your driving the engine will cut off. So far I have replaced the ignition wires, the spark plugs, the fuel filter and I have had fuel injection servic


You installed parts & asked for various services to be done

What you failed to do, was testing required to find your vehicle
problems

Most likely, unless your way behind or never do any Preventative
Maintenance, you didn't need all that was done,at least to fix the
cutting off issue

Have to check for OBD Codes,road test with scan tool,look
at data & component test, to find problems,not replace parts
in a wish & hope strategy

Sep 30, 2014 | 2000 Chrysler Town & Country

1 Answer

Isuzu trooper cuts out while driving


Diagnostics is not what most likely was done

You have a vehicle checked for OBD Codes

That is not much in the way of a diagnostic process

Vehicles do not always set codes

Codes do not tell you what is wrong

Codes do not tell you to replace anything

There are no computers used to work on
or test a vehicle

When working on a problem using codes,factory manuals
as reference material,trouble charts & test equipment,
that is diagnostic work

So you need to have that done- after a road test,at a repair shop

I would suspect your Fuel Pump is failing

Dec 22, 2012 | 2002 Isuzu Trooper

1 Answer

97 camaro cuts off when driving


Hello
The engine and automatic transmission in this vehicles drive train are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPENDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM

Aug 24, 2012 | 1997 Chevrolet Camaro

1 Answer

2002 vauxhall engined 1.7 diesel combo wont start not the pump


Hello
The engine and automatic transmission in this vehicles drive train are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPEDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM

Jul 25, 2012 | Cars & Trucks

1 Answer

I have a 97 2 door tahoe. I have trouble starting it. It turns over but wont start right away. It takes about 8-10 seconds of cranking to get it to start. It will start right away if you push the gas down...


o2 is a sensor. You could try replacing the correct one (up to 4 o2 sensors are possible any given vehicle). If check engine light is still on, have the codes cleared, have scan performed again to get the fault codes for possibly the specific o2 sensor. Hope this is helpful.

Apr 26, 2010 | 1997 Chevrolet Tahoe

1 Answer

How to reinstall the fuel injection pump on toyota 4.2 l turbo diesel(1 hd-fte)engine


Actually this is a relativly simple fix, it is located near the diesel filter {R/H of engine} and is merely removing the feed lines and plugs, replacing the gaskets and pump, you will have to prime the unit before attempting to drive, be generous with the diesel when priming, as running them dry can be costly. replace the filter while your at it and remember to fill the chamber with fresh fuel before sealing it closed. Good luck, hope it helps.

Nov 19, 2009 | 2000 Toyota Land Cruiser

1 Answer

2000 Saturn SL2 fails smog due to failure of OBD Self test


Some vehicles require very specific drive cycles (called "drive traces" if you perform them on a road simulator or dyno) to activate certain self-checks like the catalyst and EVAP monitors. As a general rule, doing some stop-and-go driving around town at speeds up to about 30 mph followed by five to seven minutes of steady 55 mph highway speed driving will usually set most or all of the monitors. Consequently, if you're checking an OBD II system and discover that one or more of the monitors have not run, it may be necessary to test drive the vehicle to set the remaining monitors.

You should talk to a good emission tec, if this is not throwing a code, it is hard to say if that one of the components could be bad. O2,pump,convert, HeO2, every part of the emission system.

With a 1000 miles, and doing what is says above just before the test, and ending driving at the test
should be plenty. If it is not, you will have to have each emission part checked, or when the computer
is plugged in it might show a code that did not trip dash light.

Mar 27, 2009 | 2000 Saturn SL

3 Answers

Stalling, 'reduced power' light, and OBD code P1125 Manufacturer control air metering...


These trucks have a drive by wire system,we seen a` lot with a broken ground wire on the rear of the drverside cyl head,this is hard to see just feel and give the wire a tug .If the wire is loose or broken the reduced engine power light will come on.

Feb 02, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

2 Answers

Why after driving car stopping & starting car radomly loose power


I would go to to autozone or advance and run and obd 2 scan. this is free so you can see what codes are coming up. I hope its not your alternator

Dec 07, 2008 | 1998 Oldsmobile Achieva

Not finding what you are looking for?
2000 Toyota Land Cruiser Logo

Related Topics:

658 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...