Question about 2005 Dodge Ram 2500 Truck

1 Answer

Water pump replacement procedure 2005 2500 dodge with cummins diesel

What is the proper procedure for replacing the water pump on a 2005 dodge 2500 4x4 with the cummins diesel

Posted by on

  • 1 more comment 
  • Anonymous Aug 30, 2008

    I have a need for a picture of the serpentine belt route and the pullys. When my water pump went out it destroyed pullys and the belt. Need to "see" what it all looks like when its together.

  • Anonymous Mar 12, 2014

    need a serpine belt routing diagram for 2005 dodge 2500 cummins turbo diesel with p/s and a/c

  • Anonymous Mar 17, 2014

    2007 dodge cummins 6.7 alternator not charging,, replaced alternator

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 3 Answers

Take off old water pump. clean up area on the motor real good.do this by using a scrapper and cleaning slolvent. when thats all done put hi temp silicon on the block water pump and the put gasket on silicon. let dry for like five minutes. put in on torque bolts to specs.

Posted on Mar 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the fuel pump pressure for a 91 dodge Cummins diesel?


what cummins diesel engine model is in the dodge
cummins make a large range of engines all of which have various pump pressures depending on the injector set up
ask your question again and concentrate on the engine details

Jan 20, 2016 | Dodge Cars & Trucks

2 Answers

My 5.9 dodge cummins diesel won't start, I've replaced the fuel lift pump, and the fuel filter, turns over. But will not start?


Most likely you just have air in the lines.Crack them open one at a time and bleed them with the fuel pump off and on till you get fuel.If it fires dont hit the throttle let it sit and idle and close the line.Does it fire up with a small whif of starting fluid?

Mar 17, 2013 | 1999 Dodge Ram

2 Answers

I ran a mixture of diesel and water thru my fuel system about three miles or so what do i do now


drain the fuel, change the filter, add fresh diesel. cycle the key several times and see if she fires up. you might have to crack the injector lines to help in bleeding the air out of the system. the good thing is the vp44 injection pump doesn't know what its pumping and 2001 24v cummins do not have electronic injectors, so you should be ok.

Mar 03, 2013 | 2001 Dodge Ram 2500 Truck

1 Answer

Is there a difference between a $60.00 water pump and a dealership $474.00 water pump for a 2005 dodge dielsel


Hi,
if you have a Cummins diesel then it probably has a geardriven water pump. Dodge gas engines have a belt driven water pump, much cheaper. Check around for a re-man water pump if you have a Cummins installed. The prices vary enormously.

Good luck.

Jan 27, 2011 | 2005 Dodge Ram 2500 Truck

1 Answer

A diagram for changing the water pump on a 2006 dodge ram 3500 cummins diesel


On a cummins turbo diesel the water pump replacement is quite simple i do believe. just have to remove the belt. The clutch fan, and pulley, then the water pump is right there i believe being held on by 4 bolts only and remove. Remember to place the wate pump o-ring on the water pump and hold in place with sort of adhesive just to make sure it doesn't slip out during installation or this will cause a leak. Once everything is installed then you will need to purge the cooling system of the air bubbles by letting it run and watching when the thermostat opens up. You can tell because the level will drop in the rad or over bottle, depending on what controls the fluid. Let it open two or three times, and go for test drive, all should be well...hope this helps

Aug 24, 2010 | Dodge Ram 3500 Cars & Trucks

1 Answer

Water pump needs replacement.cummins diesel


the water pumps on these engines are some of the easiest to replace. just take the belt loose. unbolt the water pump and pull it out. scrape whatever pieces of the old gasket are on the block off. and install new water pump and gasket. the put the belt back on.
here is a better demonstration with pics:
http://www.cumminsforum.com/forum/3rd-gen-tech-articles/182382-water-pump-thermostat-replacement.html

Oct 23, 2009 | 2004 Dodge Ram 2500

1 Answer

1999 dodge diesel 2500 seems to have a fuel related problem.


Please clarify the "loosing power" does it lose power and shut down or does it loose power but will idle? Your Cummins is electronically controlled so oil condition is important, fuel leaks, oil leaks, leaks in the air ducting between the turbo and the intake, sensors, water in the fuel. Do you get an engine light when this trouble happens? Dodge uses a lift pump to carry fuel to the the injection pump, is it working?

May 31, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

Engine replacement


any of the non computerized aka 12 valve cummins will interchange going from the p7100 pump on the 94 to the ve injection pump on the 92 may mean rerouting some of the fuel lines to hook it up. make sure you use all the sensors from the 94 engine though so all your gauges read correctly other than the fuel system the engines are identical though so should have no issues doing this

Apr 27, 2009 | 1994 Dodge Ram 3500

Not finding what you are looking for?
Cars & Trucks Logo

1,728 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...