Question about 2007 Lexus RX 350 FWD

1 Answer

Navigation does the 6.1 navigation have a override (to program it while the car is in motion) Also is there a way to increase the text display while using sirius satellite radio

Posted by on

  • MavericksF15 Aug 23, 2008

    The Lexus RX350 has the only navigations system that will not let you use it while driving. you must pull over to the side of the road and reprogram the system.
    I was almost sideswiped by an 18 wheeler not once but three times while stopping to reprogram my RX350. 
    I love the car but the navigation system sucks. I am probably going to spend $3500 and put in an aftermarket GPS system that I can use while driving unless Lexus reprograms their software to stop this nonsense. I would even go as far as to sign a waiver  and hold Lexus not libel if an accident occurred while using the nav system in my RX 350.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to find out where the valet/override button is located on my car....trying to program a new keyless remote


1. Insert key into the ignition and turn it to the On or ACC position, turn off radio. (do not start the vehicle)

2.Press and hold DISP button on radio until settings is displayed.

3. Press Seek until FOB PROG is displayed .

4. Press Prev or Next and BEGIN will be displayed

5. Press DISP and programming will begin when PUSH FOB is displayed. Press and hold Lock and Unlock together until vehicle chimes. This will signal successful programming. May have to hold buttons up to 20 seconds. Hold Lock and Unlock on additional remote until vehicle chimes again.

6. Exit programming mode. Scroll to Exit and press DISP to exit programming.

If you don't have the original radio, it can be done with a scanner.

Mar 19, 2016 | 2004 Chevrolet Chevrolet Impala

2 Answers

Can I reprogram my keyless remote from my 1995 eldorado to my 1996 cadillac eldorado


AS programs can be altered I would have it checked out at a dealer service centre as they will need the keys and the vehicle to see if it can be done

Jan 11, 2014 | 1996 Cadillac Eldorado

1 Answer

05 navigator shift lock actuator problem wont come out of park. i would like to know how to override so i dont have to pay a tow bill thank you


You need to remove the silver trim plate from around the shift console. This is done by gently prying it up using a screwdrive or similar tool (sometimes this can be done using only your fingers). At the top left corner of the grey shift cover you'll see a the word "OVERRIDE". There is a small plastic cover that needs to be rotated out of the way and then you can insert a small screwdrive/fingernail file or similar device into the slot and push down. This will allow the shifter to be moved out of PARK.

Aug 07, 2011 | 2005 Lincoln Navigator

1 Answer

How do I program a Cadillac 2004 Deville remote key fob?


came across this, maybe this will help out...this is for analog gauges....

With the ignition in the "RUN" position (engine does not necessarily need to be running, but it will work either way).
Press OFF and WARMER (or the OFF and PASSENGER WARMER buttons) on climate control panel simultaneously. Instrument Panel Cluster (IPC) will light all telltales, then go blank. System is now in DIAGNOSTIC MODE. After diagnostic mode cycles through and stops, press FAN DOWN button until "RFA?" is displayed, then press FAN UP. If "RFA DATA?" is displayed, press FAN DOWN. If "RFA OVERRIDE?" is displayed press FAN UP button.

If "RFA S00 NO OVERRIDE" is displayed, press FAN DOWN. If "RFA S01 PROGRAM FOB #1" is displayed, press FAN UP button.

IPC will show "0" on right side of Drivers Information Center (DIC) display. Press WARMER button on the climate control unit until "99" is displayed.

Press and hold TRUNK button on the transmitter. While holding TRUNK button, press LOCK button and hold both buttons for a total of 3 seconds. Locks will cycle when programming is complete. If transmitter is not programmed within 30 seconds after entering "99" on the display, system will default and you must begin at step #2 again.
To program second transmitter, press FAN DOWN button until "RF S02 PROGRAM FOB #2" is displayed, then press FAN UP. Repeat step #4.

To exit system, press AUTO, MODE UP, MODE DOWN, or RESET button.
__________________

Oct 30, 2010 | 2004 Cadillac Deville

1 Answer

What would cause my engine to hesitate when in motion?


A bad plug, If the car is sitting at idle it doesn't require a lot to keep the plugs firing, so when you drive the spark increases more frequent and one of the plugs may not be able to fire on every stroke at the best it should causing a mis-fire. If you change these, use a OEM type because some of these platinum and higher rated plugs will make a 4 or 6 cylinder runs worse. I've seen this happen quiet often.

Sep 09, 2010 | 1994 Nissan Pickup

1 Answer

My 2010 Lexus RX350 Navigation System is responding VERY SLOW!


If Lexus can't fix this there is nothing anyone here can do for it. Anything that can be done needs the proper scanning and reprogramming equipment only Lexus has. Being that the car is new when enough people complain about this they will come up with a fix, Their may be a recall on it in the future. But for now your going to have to live with it or trade the car in. I know you did'nt want to hear this but but if some yahoo directs you wrong it will cost you hundreds just to get the programming back to the way it is today. Some navigation systems if you disconnect the battery you will have to go to the dealer to get them to reprogram it. Use lots of caution when guessing. New cars are not made for the average back yard mechanic to touch.

Aug 10, 2009 | 2004 Lexus RX 330

2 Answers

How do i program a key fob for a 1996 cadillac deville


you need to get a tech 2 to be able to promram the key fob

Aug 02, 2009 | 1996 Cadillac DeVille

1 Answer

Programing a new remote


Use these instuctions if your Deville has an Analog Instrument Cluster
1. Press OFF and WARM buttons on Climate Control Panel (CCP) simultaneously.
(Instrument Panel Cluster (IPC) will light all telltales, then go blank) System is now in diagnostic mode.
Press PASSENGER COOLER button until “RFA” is displayed, then press FAN UP.

If “RFA DATA” is displayed, press FAN DOWN.
If “RFA OVERRIDE” is displayed, press FAN UP.
2. If “RFA 500 NO OVERRIDE” is displayed, press FAN DOWN.
If “RFA 501 PROGRAM FOB #1” is displayed, Press FAN UP.
3. IPC will show “0” on right side of Driver Information Center (DIC) display.
Press warmer button on climate control unit until “99” is displayed.
4. Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
step 2.

5. To program a second remote, press FAN DOWN button until “RFA 502 PROGRAM FOB #2” is displayed, then press
FAN UP. Repeat step 4.

To exit system, press AUTO, MODE UP, MODE DOWN, or RESET.




Use these instructions if your DeVille has a Digital Instrument Cluster
1. Press OFF and WARM buttons on Climate Control Center (CCC) simultaneously. Instrument Panel Cluster (IPC) will
light all telltales, go blank then enter DIAGNOSTIC
MODE. Press FAN DOW button to scroll through system until
“RFA” is displayed, then press FAN UP button. Press FAN DOWN button until “RFA OVERRIDE” is displayed, then
press FAN UP button. When “NO OVRD RF 500” is displayed, then press FAN UP button.

2. When “PGM FOBL 501” is displayed, press WARM button and “99” will be displayed in left upper corner of IPC just
below odometer. System is now ready to program remote.

3. Press and hold TRUNK button on transmitter. While holding TRUNK button, press LOCK button and hold for one
second. Hold both buttons for a total of 3 seconds. Locks cycle when programming is complete (if remote is not
programmed within 30 seconds after entering “99” override display, system will default and you must begin again at
step 2.)

4. To program second remote, pres FAN UP button until “PGM FOB2 502” is displayed, then follow steps 2 and 3 to
program second remote.

To exit system, press RECIRC or RESET buttons.

Disclaimer

Apr 25, 2009 | 1998 Cadillac DeVille

1 Answer

Allow the factory toyota nav system to display DVD while moving?


You have to look up how your dvd is wired and give it a new ground since i am sure it only works while in park.

Mar 09, 2009 | 2008 Toyota Tundra

Not finding what you are looking for?
2007 Lexus RX 350 FWD Logo

665 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...