Question about 2002 Ford F150 Regular Cab

2 Answers

Axel removel f150ford

Cant pull it out

Posted by on

2 Answers

Why are you trying to remove it?

Posted on Sep 02, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

Is it rear axle?

Posted on Aug 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change altenator on a 6 cyl front wheel drive, do I have to pull the axel to get bottom bolt out if so how


havn't said what vehicle but i doubt you would need to remove the axle , send the make ,model etc and i'll have a think cheers

Oct 07, 2014 | Cars & Trucks

1 Answer

Cant get driver side cv axle out on a 96 ford escort 1.9l


if you have taken the half axel off the wheel arm, then all it should take is a hard pull by hand to pop the half axel out of the transmission.

Jan 09, 2014 | Ford Escort Cars & Trucks

2 Answers

I need to remove the driver side axle and i cant get it out of tranny


There is a "C" clip that holds it in there. Put your pry bar on the fat part of the halfshaft (axle) and give it a few smacks with a hammer. These jolts should knock it loose to be able to remove it. If you cant get room to hit it with a hammer you will have to use a pry bar and just keep working at it on both sides.

Jan 15, 2011 | 1996 Dodge Neon

1 Answer

Trying to replace right front bearing hub and cv axle [bad boot on upper end] cv shaft outer hub will not clear the shock or stabalizer bar for removel and replacement on 06 f150 4x4 pulled bottom bolt...


If you have the jack in the correct location have you attempted to turn the front wheels to slightly adjust the angle of the hub relative to the shock and stabilizer bar?

Jul 25, 2010 | 2006 Ford F-150

1 Answer

Replace ac clutch for 96 previa


is it manul or automatic either way you have to do the following remove prop shaft then unbolt the gearbox from engine then unbolt the gearbox mount and lower via a jack and pull back and the clutch is there in front of you six more bolts and its in your hand refitting is the reverse of removel you will be able to doit on the ground and use good axel stands and jacks

May 11, 2009 | 1992 Toyota Previa

1 Answer

Need 2 get axels out of ford 8.8 rearend. I got it all apart but i cant get the axels to come out. I need to replace the axel seal and bearing. Hope you can help.


Do you have the pin in the differential out & "c" clips removed, or is it a different system? Once pin is out you push in slightly on axles & remove "c" clip, then pull them out.

Apr 26, 2009 | 1992 Ford Ranger

1 Answer

Front right universal joint removel


no but you have to remove the driveshaft.

the bolts are 8mm on the driveshaft to rearend u-joint

Apr 11, 2009 | 2008 Dodge Ram Pickup 1500

1 Answer

Sterling collum is stuck trying to remove the keyclindor replac


there is a small hole on the cylinder use a pick and push the lock up at the same time turn the key and just pull.

Apr 05, 2009 | 1998 Nissan Altima

1 Answer

87chevyG30 5.7lV8 core plug removed w/out taking out engine?


You should not have to pull the motor to replace any of the freeze plugs, except the 2 on back of engine block witch requires engine removel or trans. removel. Depending on witch one thats leaking. There are 3 on each side, and 2 on the rear of engine, most common one to leak is the one above the starter, witch requires starter removel, there is one in the middle thats you have to jack up engine to remove engine mount to get too. There all located below exhaust manafold on each side. They are a bear to chg. but can be done without engine removel.

Mar 29, 2009 | 1987 Chevrolet G30

1 Answer

I replaced my ignition switch on my 1982 f150ford pickup;but now i cant get my key 0ut of the ignition.


i had that problem on a 92 mercury what i had to do was actually push up on the gear selector and turn the key to the off position then the key should come out.

Mar 07, 2009 | 1982 Ford F 150

Not finding what you are looking for?
2002 Ford F150 Regular Cab Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...