Question about 2001 Ford Focus

1 Answer

Can you help me please?

I am have a problem with my ford focus LX. the codes read Fuel Pump Driver Mod and Cyl 1 & 2 Misfire. i have replaced the spark plug. when i pulled out Cyl 2 spark plug it had either Oil or Gas in the threads and it was still wet. now it wont start. i am not for sure how to test if it is the driver mod or the fuel pump now. can you help me?

Posted by on

  • sandowen Aug 26, 2008

    no clicking noise. battery is good.. altnator has been checked and it is still good.. what else wont let the car start? the starter is good. it sounds like the car is just not getting and gas.

  • mike May 11, 2010

    i had simila problem on ford ka it was fault moduel pack

×

Ad

1 Answer

Clicking noise and won't start.

Posted on Aug 23, 2008

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22246 Answers

SOURCE: Fuel Pump

number 2 cylinder has broken rings ,or the coilpack/leads need replacing check for current to fuel pump if no power checkfor spark if no spark either it could be immobiliser

Posted on Nov 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 ford focus we have replaced the fuel pump after trblshooting the vehicle would run at idle if started with a id of carb cleaned down the throat. Thw new pump required a mod to the tank removing the...


componet located directly behind the tank ? evap canister ! Do you know how to test automotive electrical ? How to read an use a electrical wiring diagram ? Use a DVOM - digital volt ohm meter ? Do you know what a FPDM is fuel pump driver module (computer) Your best bet take it to a qualified repair shop or dealer ? Ford Electronic Returnless Fuel System Diagnosis Part 1 Ford

Apr 05, 2017 | 2001 Ford Focus

2 Answers

Help on finding out wind star coads PP0171-/-P074-/-P0401


first PO171 o2 bank 1 s1 lean PO174 o2 bank2 lean
PO401 cyl 1 misfire
when an engine misfires the oxygen sensor will read the oxygen from that cyl sensor doesnt read fuel so every misfire is a air pump to diagnose we have to fix misfire first check the coil wires and plugs for cyl 1 use spray bottle with water run engine hot at idle spray wires with water if enging runs rough shakes or stalls then replace the wires dont spray with to much water if the wires are real bad you may not be able to restart engine

try this first once fix misfire clear codes and drive it

plz comment vote reply if you need more help

Jan 17, 2011 | Ford Windstar Cars & Trucks

1 Answer

I have a 2003 Expedition 5.4L Triton. Two days ago, with low gas (38 miles to empty), engine started running rough. Code read P0302, misfire cyl. 2. Since it had 113K miles, I figured its time to change...


Most likely the coils. Easiest way to check is swap them with another cylinder, start it, pull the plug wire connecter and if it doesn't change the engine the coil is bad. If it is the injector, then you can check it with an ohm meter. Touch the leads in the injector it should read 11 to 15 ohms. if you need help let me know.
Randy

Dec 02, 2010 | 2003 Ford Expedition

1 Answer

P0303 and P1300 together (Cyl. 3 Misfire)


CODE P1300 IS MISFIRE DETECTED FUEL PROBLEM. WHICH MEAN 3 FUEL INJECTOR IS CLOGGED UP.HAVE FUEL INJECTORS CLEAN AND CHANGE FUEL FILTER.

Jul 24, 2010 | 1999 Audi A4

2 Answers

1998 Park Avenue: it may not be getting fuel how can i verify this??...


the easiest and fastest way is to listen for pump activation when you turn you key to the on posistion turn your radio off turn the key to on (just before the point of starting)and you should be able to hear the humming or vibrating if you dont then you are not getting fuel. if the pump is working or you cant tell if it is go to the fuel rail look foe a cap that looks like a valve stem cap take this cap off and push the stem in if you get fuel then you know that you donthave a fuel problem if you dont get fuel to the rail then its probably the pump. hope this helps you.

May 07, 2010 | 1998 Buick Park Avenue

1 Answer

Engine warning light comes on, diagnostic says


if your car give you i code thats says mutlipul misfire on number 1,2,3,or four cyl. that means that that cyl is not firing when its suppost to so if the code says number 3 cyl misfire or multipul misfire replace number 3 spark plug and coil pack and 80% of the time that will solve the problem.

Oct 08, 2009 | 2006 Ford Focus

1 Answer

2000 FORD FOUS MISFIRE


try a new set of spark plugs if that does not work it might be ignition related, a plug wire or something like that.

Jun 08, 2009 | 2000 Ford Focus

2 Answers

Fuel pump.


I have a 2000 ford focus and there was a recall for a defective fuel pump. THe dealership replaced it for free. You should check Ford recalls for this problem.

Oct 21, 2008 | 2000 Ford Focus

1 Answer

Fuel Pump


number 2 cylinder has broken rings ,or the coilpack/leads need replacing check for current to fuel pump if no power checkfor spark if no spark either it could be immobiliser

Aug 21, 2008 | 2001 Ford Focus

Not finding what you are looking for?
2001 Ford Focus Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...