Question about 1999 Daewoo Nubira

1 Answer

CAR DO NOT START

BATTERY FULL ENGINE JUST CRANKING.nO SPARK FROM COIL TO DISTRIBUTOR,ALSO NO POWER TO COIL

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 71 Answers

Hey

bring power directly to coil and try and start it!! if it starts then check the wires going to coil!!

Damien

Posted on Aug 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine cranks has spark at distributor but wont start.


standing for a while could be stale fuel
efi or carby
is it a points or electronic module distributor
could be coil, or plug, leads points

Jul 16, 2016 | Cars & Trucks

1 Answer

I have a 1999 Tahoe 8 cylinder I put in a new coil a whole new distributor distributor cap still it will not start


Pull the coil wire off the distributor cap. Put a ***** driver in it and place it close to any metal on the engine. crank over the engine. If you have spark, replace the pick up coil/ignition module in the distributor. If you have no spark. Check for power and ground at the coil plug with engine on. If it is there , replace the crank sensor.

Apr 18, 2016 | Cars & Trucks

1 Answer

I have a 1996 Jeep Grand cherokee with the 5.2l v-8 engine. Last week I started it, and it ran for about 1 minute before shutting off. The engine cranks, but no ignition. I replaced the Crankshaft position...


Time to meter voltage. Start with the 12V circuit. Are you getting voltage at the coil. Does the voltage fluctuate when the engine cranks? If yes to both check the high voltage circuit. Start with the coil then the distributor then each plug. You should be able to find where the spark is failing.

Sep 07, 2014 | 1996 Jeep Grand Cherokee

2 Answers

Engine cranks but no start, no spark. What else can I check?


is it actually rotating when the engine turns over I know sounds stupid but I\'ve seen the teeth that goes inside against the cam break off on first turn over happened to me once on a Honda, also that same car my original problem was I was getting power and everything like you but the icm on the distributor was putting the power out on the ground side and the power turned to ground not allowing the distributor to do its job and produce spark





hope this helps

Aug 29, 2014 | 1994 Toyota Corolla

2 Answers

It turns but it wont start,it has gas and power


Pull off the coil ignition cable at the distributor and check for spark coming out of coil when cranking engine over. Use a heavy rag or glove to hold the wire 1/4 inch from a metal ground. Should see a strong blue spark when cranking to verify ignition is good. If no spark, check for battery voltage to coil on the coil primary. If you have current to the coil, suspect a bad coil, ignition module, crank position sensor, or cam position sensor, or pcm. The coil, ignition module, and sensors can be tested before replacing.

Jan 29, 2013 | Cars & Trucks

1 Answer

1990 Dodge Ramcharger won't start. Battery output 12v, voltage across coil terminals 6v, voltage output at coil port to coil wire 6v, voltage of coil wire output to distributor 6v. Engine will c


There should be a small white ceramic block on the firewall - this component cuts the battery voltage from 12 to 9 volts for the coil and ignition system. It has 4 wires and is called a ballast resistor.
You may need a book with the wiring diagram to be able to test it. You should have battery voltage going in and something like 9 volts coming out.
You can also run a wire with a fuse from the battery to the positive side of the coil to check the system. Disconnect the factory wire from the coil first.

Jan 27, 2013 | Cars & Trucks

3 Answers

No spark


First does the rotor turn when cranking engine?? possible timing chain is out or stripped gear..are you sure it has no spark??did you verify this with a high output spark tester ? did you spray starting fluid in the tbi unit ?

Mar 23, 2012 | 2000 Chevrolet Astro

2 Answers

1990 honda wont start or crank, the lights dont come on, head or inside the car


The distributor in the hondas has a function of also engaging the coil to create spark. No spark = no fire. Perhaps take a plug out, leave the lead on, hold it with INSULATED pliers against a solid metal part of the engine and get someone to crank the engine over.

If the plug sparks - coil and firing switch OK. If no spark, check coil first - remove main + feed lead from coil terminals and check on a meter for power with key on but NO motor cranking. No power = faulty distributor/firing switch.No other ideas sorry!

If it won't turn over you may want to check Battery cables for tightness and/or corrosion Starter solenoid Neutral or clutch safety switch

May 23, 2010 | 1990 Honda Accord

1 Answer

Van will not start I have fuel pressure and when cranking it builds oil pressure where do i go from here


Check for spark at the spark plugs. If no spark, remove distributor cap and inspect the inside of the cap and the rotor for obvious signs of wear or damage. Check for spark at the coil wire by removing the coil wire from the center of the distibutor cap, and, holding the end of it close to the engine block, have someone crank the engine. There should be a very strong spark. If there was spark at the coil but not at the plugs, replace the distributor cap and rotor. If there is no spark at the coil, you either have no power or ground at the coil, or the coil is bad. With the ignition ON, there should be 12v at the red wire for the ignition coil. if not, check the fuses. Check for the pulsing ground signal of the ignition coil at the other wire ( I think a white wire) using a test light clipped to battery + while the engine is being cranked. If there is no light, the problem is likely the ignition module or pick-up coil, which is located in the distributor. Make sure that the wiring and connections are in good shape for these items before condemning them.
Pick-up coil should have about 1500 ω of resistance.
Good Luck

Sep 30, 2009 | 2003 GMC Safari

2 Answers

The engine is cranking want start


check for fuel .? spray staring fluid into throtle body then crank if engine runs then stalls you have fuel related problem ( fuel pump) if no start you have ignition problem ( coil or distributor check for spark use a screw driver insert into spark plug wire at spark plug end hold about 1/4 away from gronded engine and crank engine see if spark jumps gap if no spark could be coil or crank sensor

Feb 26, 2009 | 1993 Subaru Impreza

Not finding what you are looking for?
1999 Daewoo Nubira Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

yadayada
yadayada

Level 3 Expert

63291 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...