Question about 1986 Honda Prelude

1 Answer

'86 Prelude Si Interior Panel Removal

I can't get behind the back seat side panel to get to the seat belt. This isn't a car make I'm familiar with. I just need to know how to remove the inside back seat panel; driver's side. Any tips?

Posted by on

  • Anonymous Sep 25, 2008

    idk i have the same problems

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I did this the other day. I think there were 1 or 2 screws holding it in place that you have to remove the bottom part of the back seat to get at them.

Posted on Feb 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Tahoe. Where is the auxiliary blower motor located?


It is located behind the right rear quarter panel , In the back right of the interior !
Remove the right rear quarter trim panel. Refer to Rear Quarter Trim Panel Replacement - Right Side in Interior Trim.
Removal Procedure
  1. Remove the rear seat. Refer to Rear Number 2 Seat Replacement or Rear Number 2 50-50 Seat Replacement in Seats.
  2. Remove the Third Pillar trim panel. Refer to Third Pillar Trim Replacement .
  3. Remove the garnish molding. Refer to Body Rear Corner Garnish Molding Replacement .
  4. Remove the door sill plate. Refer to Liftgate Door Sill Plate Replacement .
  5. Remove the quarter panel trim screws.
A lot involved in this but not to difficult !
  1. Remove the rear door sill trim plate. Refer to Front Side Door Sill Plate Replacement or to Rear Side Door Sill Plate Replacement .
  2. Remove the lower rear seat belt cover and bolt.
  3. Remove the trim panel from the vehicle.
Remove the sill plate. Firmly pull the sill plate up and out from the retainers.
Remove the sill plate from the vehicle. Start from the front of the door sill. Use a flat-bladed tool in order to pry the door sill plate.
Rear Side Door Sill Trim Plate Replacement
Use a flat-bladed tool in order to pry the door sill plate. Remove the sill plate from the vehicle.
Body Rear Corner Garnish Molding Replacement
Remove the rear upper garnish molding. Refer to Rear Upper Garnish Molding Replacement .
Pull down on the upper corners of the garnish molding in order to disengage the retaining clips. Pull in order to disengage the remaining retaining clips. Remove the rear corner garnish molding from the vehicle. Inspect the rear corner garnish molding for broken or missing retaining clips. Replace the retaining clips as needed.
Good Luck ! Fun job !!!!!

Jun 07, 2015 | 2006 Chevrolet Tahoe

1 Answer

Where is the location of the fuel pump driver module on a 2001 mercury cougar


This module is located behind the interior side trim panel, LH side behind the front seat, below the rear LH side glass. AKA B Pillar trim panel. Access from inside, probably will require removal of the rear seat bottom and even top of seat to remove the panel. it will be the small box in the center of that area once the panel is removed. Good luck!

Sep 20, 2014 | 2001 Mercury Cougar

2 Answers

We need to find the key pad mogulater to find the key code


no such thing as a key pad modulator ,key code is a dealer only thing

Jan 13, 2011 | 1998 Ford Explorer

1 Answer

Where is the data link connector in a 86 honda prelude


This 86 Honda Prelude does not have a link connector, code's are read from the computer it's self, the computer is under the passenger seat or under the carpet on the passenger side, you count led light flashes and on the computer panel will have the trouble code's refernce.

Jul 02, 2010 | 1986 Honda Prelude

1 Answer

How can I get my Prelude door open? Nither handle works from inside or outside. I need to get the inner panel off the door to fix it but I first need to get the door open. I have a 1992 Prelude SI.


to make life easier take the seat out, then start to take inner door panel off, at least you can get to the linkage,which is hanging off.slide seat forward and undo 2 bolts on floor inside runners,then slide back and undo 2 bolts in front runners.the rest is self tappers and clips(that break easy)

May 12, 2010 | 1998 Honda Prelude

1 Answer

I need to replace a rear seat belt in a 1997 Ford Tarsus. Does any know the best way to access the assembly? In addition, are there any diagrams available that show the connection points?


please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal
  1. Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear Sedan
Removal
  1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
  1. Remove rear seat cushion from vehicle.
  1. Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear 60/40 Split Bench—Sedan
Removal
  1. NOTE: Safety belt bolts do not secure seat back to vehicle.

    Remove rear seat cushion as described.
  1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
  1. Remove two bolts from outboard rear seat back frame retaining brackets.
  1. Lift seat back up and pull forward to remove from vehicle.
  1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan Removal
  1. Remove rear seat. Refer to Section 01-10 .
  1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
  1. Pull lower quarter trim panel away from body.
  1. Remove safety belt retaining bolt.
  1. Feed safety belt through lower quarter trim panel.
  1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
  1. Remove retractor anchor nut and retractor from rear quarter panel.
  1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
  1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
  1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.


    2a6fac0.gif


    Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)
  1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.


    fff90b0.gif

Installation
  1. To install, reverse Removal procedure.
  1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
  1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
  1. Check the restraint system for proper operation.

Jun 30, 2009 | 1997 Ford Taurus

1 Answer

Looking for interior fuse box on 86 toyota camry


Look behind the driverside kick panel. There is a removable panel. You will find the fusebox behind that panel.

May 18, 2009 | 1986 Toyota Camry

1 Answer

Replacing middle seat belt in 97 Dodge Caravan


If I recall correctly the belt actually is mounted behind the interior trim panel. It 1 piece on a short wheel base & 2 piece on a long. You must remove both seats (2nd & 3rd row) to hah room to remove the trim panel . BE CAREFUL the get very brittle and snap if you pull the wrong way

Mar 19, 2009 | 1997 Dodge Grand Caravan

2 Answers

2003 volkswagen beetle covertible quarter panel removal


I do not recommend this job unless you are a seasoned mechanic, VW dealership charges $1000 for a reason. They almost earn it on this one. but heres how it's done or how I did it any way. the complete job took me 4 hours and I been at this for 30 years. But a lot of this time was figuring out how it came apart. First, drop the top, pull up on seat bottom and remove it, remove center panel, remove 3 allen bolts at bottom on seat back and remove. headrests, they just pull off, raise top just enough to make hinged panels flip up. remove nut at top rear corner of side panel. you can see the back side of the nut and bolt it is on from the panels that flip up. Remove Nylon push lock rivet where seat belt goes through panel on rear, top, corner. Pull out on panel to release it, there is 5 or 6 nylon locks that just pull out of holes in the body. It will sound like your breaking it when the locks pop loose, or mine did. then lift to gain access to remove seat belt bolts and unplug flip panel motors. remove cable end from its clip. Pull seat belts through panel. Set panel a side. remove torx head bolt around oval panel that speaker is mounted on. unplug speaker and regulator and pull wire harness thru hole. remove 2 allen and 5 hex bolts at top where window would come out if it worked. pull up on plate and move rubber window seal to the side to remove plate. remove 2 nuts at bottom of regulator and one about half way up towards front, lift regulator and window up through top to gain access to 3 nuts that hold window to regulator, from the top lift window out first then regulator. Reverse to assemble it.

Aug 12, 2008 | 2003 Volkswagen New Beetle Convertible

3 Answers

Leaking sunroof


Had same problem with 91 Prelude, after rain, water would leak from moonroof, especially when stopping, having a wet neck on the way to work is not fun! Solution was to remove the small screens and restrictor caps on the drain hoses. The hoses can be acessed through the trunk behind the quarter panel cover on either side, just have a can ready for the skanky water to drain once the plugs are removed. When all clear, the drains should drain out right behind the mud flaps in the rear on each side. There are fron drains as well, these run behind the driver and passanger kick panels and drain around the mud flaps in the front.

Jul 24, 2008 | 1991 Honda Prelude

Not finding what you are looking for?
1986 Honda Prelude Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...