Question about 2003 Nissan Xterra

1 Answer

Power plugs I have a 2003 Xterra. The Plugs in the Console and the back seat dont work anymore. I think they maybe disconnected, How do I get to them? Thank you

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

Have you checked your fuses?

Posted on Aug 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power (driver) seat won't recline; everything else works


I would first disconnect and recommended checking if something is tangled in the track and make sure plugs in good

Nov 22, 2013 | 1998 Toyota Avalon

1 Answer

My wifes 2003 nissan cranks over but wont start. i removed backseat cover and checked power at the wiring harness, i didnt get any power at all, i checked the fuse panel but nothing is marked that says...


you need to check for power as soom as you turn the key. you loose power afterabout 7 seconds after turning the key to "ACC position". there is a relay in system that shuts off tha power to the pump after about 7 seconds or so. personally I think that you have an issue with the sending unit. xterra has a campaign for sending ubit replacement, because they corrode on the inside of the connection on top where tha connector plugs in under the seat that you took out. This is what you will do: have someone crank the vehicle as you move the 2 wire connector on top of the gas tank. it may start. If not, then take your vin number to the nissan dealer and see if it applies for the sending unit replacement. you may even need new gas tank which is covered under the campaign if its too rotted on top.

May 24, 2011 | 2003 Nissan Xterra

1 Answer

How i can replace the gearshift?


SECTION 501-12: Instrument Panel and Console 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Floor Console -Front, Navigator Removal and Installation
  1. Apply the parking brake.
  1. Position the front seat forward.
  1. Remove the two front floor console rear bolts.
  1. Position the front seats rearward.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the pin-typ retainer and the window control switch panel.
    • Disconnect the electrical connectors.
  1. Move the shift lever to NEUTRAL and position the shift indicator bezel aside.
  1. Remove the screws and the center console finish panel.
    • Disconnect the electrical connectors.
  1. Disconnect the shift cable.
  1. Disconnect the front floor console electrical connectors.
    1. Loosen the electrical connector bolt.
    1. Disconnect the connector.
    1. Disconnect the electrical connector.
  1. Remove the front floor console side finish panel.
    • If equipped, disconnect the electrical connector.
  1. Remove the front floor console front bolts.
  1. Remove the floor console.

Feb 13, 2011 | 2003 Lincoln Navigator

1 Answer

Nissan xterra 2003 one breaklight top one is not working. I have change bulb but it is not working


Could be bad contact inside socket. Try turning all lights off and use a file, sandpaper or screwdriver to scratch off any corrosion or contaminent. If this works put white grease on contacts. If this doesn't, then it has to be wiring harness. Follow wires back 'til you find break or disconnection wires or ground.

Jun 29, 2009 | 2003 Nissan Xterra

1 Answer

How can I remove gear shift knob on a 2003 Navigator?


it looks like you disconnect the shift cable and remove the center console finish panel with the shifter.


SECTION 501-12: Instrument Panel and Console 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Floor Console —Front, Navigator Removal and Installation
  1. Apply the parking brake.
  1. Position the front seat forward.
  1. Remove the two front floor console rear bolts.
  1. Position the front seats rearward.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the pin-typ retainer and the window control switch panel.
    • Disconnect the electrical connectors.
  1. Move the shift lever to NEUTRAL and position the shift indicator bezel aside.
  1. Remove the screws and the center console finish panel.
    • Disconnect the electrical connectors.
  1. Disconnect the shift cable.
  1. Disconnect the front floor console electrical connectors.
    1. Loosen the electrical connector bolt.
    1. Disconnect the connector.
    1. Disconnect the electrical connector.
  1. Remove the front floor console side finish panel.
    • If equipped, disconnect the electrical connector.
  1. Remove the front floor console front bolts.
  1. Remove the floor console.

Apr 17, 2009 | 2003 Lincoln Navigator

1 Answer

Disconnect the electrical connector


There should be just a clip on the connector that pops up and releases from the bulb.

Apr 04, 2009 | 2003 Nissan Xterra

2 Answers

Front and center console 12v accessory power outlets not working


look under the drivers rear seat for the rear fuse block it will be under a black box right there

Aug 25, 2008 | 2003 Chevrolet TrailBlazer

1 Answer

Spark Plugs


It is very difficult to change it is all done by feel as you cannot see it. You need to pull the wire off and "remember" the path it took to come out as this is the way you will have to remove and install the plug and put back the wire. Also, be very mindfull while installing the plug because it can be stripped out fairly easy if your not carefull. Good luck.

Jul 21, 2008 | 2003 Nissan Xterra

Not finding what you are looking for?
2003 Nissan Xterra Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

71525 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...