Question about 2000 Subaru Forester

Open Question

2005 Sabaru Impreza Hazard Lights on constantly

I seem to have a problem with my hazard lights on constantly and the onlu way i can stop them from flashing is to remove the fuze. I had a remote auto starter installed after purchase in 2005. I wonder if this could be part of the problem?

Posted by on

  • KICVP Aug 21, 2008

    Replace what? The fuze has been replace, are you saying the hazard switch? what exactly are you suggesting I replace? Thanks

  • pro600 Feb 07, 2009

    hazard lights wont switch off.help

×

5 Suggested Answers

  • 1 Answer

SOURCE: 2002 Workhorse chassis RV hazard flasher doesn't work

I am looking for a locking gas cap for my 2005 Bounder 36Z. This motorhome has a Workhorse chassis. Can you help me locate the part number and a dealer near Newberg, Oregon?

Thank you.

Sharon Bladow
503 554-1281

Posted on Aug 15, 2008

dr_greg
  • 192 Answers

SOURCE: Replacing hazard swith for Honda Accord 1996

u must remove the center console....remove the ashtray..(pull it ) remove the plastic trim piece around the shifter , should just pop off ,,,held on by clips...u will see 2 phillips screws under that piece., the 2 screws that secure the trim panel that ur hazard switch is attached to.....remove those screws and gently pull the panel off , u may have to unplug the clock and otherm necessary connectors includeing the hazard switch connector to remove the panel..u should be able to remove the switch with a screwdriver..reinstall everything back the way u took it off...be sure to plug the cig lighter back in...

Posted on Apr 10, 2009

joecoolvette
  • 5660 Answers

SOURCE: no brake/hazard lights,have running/turn signal lights

Suggest you change hazard flasher 'can' first, then go to the hazard switch. I'm betting it's the flasher can.

Posted on May 11, 2009

  • 1596 Answers

SOURCE: Hazard Lights Won't Work on 96 Taurus

FIRST Check for Blown Fuse Then Locate Flasher Units @ Fuse Block to Determine Wiitch one is Hazard Turn On Key Then Turn Syg. Feel Flashers The One you feel Clicking is For Turn The Other IS Flasher Replace this Flasher unit.

  1. Verify the customer's concern by operating the turn signal/hazard flasher lamp to duplicate the condition.
  2. Inspect to determine if one of the electrical concerns apply: VISUAL INSPECTION CHART Electrical
    • Circuitry open/shorted.
    • Fuse junction panel Fuse:
+ 15 (10 A) + 29 (15 A)
  • Damaged multi-function switch.
  • Miniature bulb burned out.
  • Damaged lamp.
  1. If the inspection reveals obvious concern(s) that can be readily identified, service as required.
  2. If the concern(s) remains after the inspection, determine the symptom(s) and go to the Symptom Chart. See: ProceduresSymptom Chart(s)

Posted on Jun 01, 2009

Molson02536
  • 3854 Answers

SOURCE: Constant clicking from flasher unit

The flasher unit has gone bad and needs to be changed. The flasher module is a part of the hazard module also. The clicking is the unit is still working but there is not enough voltage to activate the lights to flash. It's common on the Malibu's and other GM product cars similar to the Malibu like Grand Am's Ect. I believe Auto Zone has the replacement part for you car and is more reasonable in price then the dealer and the y also have the step by step instructions to replace the flasher module. Good luck and keep me posted, be glad to help.

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hazard lights Comes up without switching them on.


You have constant power to the hazard switch. Replace the switch. it is shorting out.

Jul 25, 2015 | 1998 Jaguar XJ8L

1 Answer

2005 Dodge Durango 4.7 my hazard lights stop working.It's not the fuse.Could it be the relay?Where is the relay to the hazard lights?


Hello,
Both the signal and hazard relay is located at the top of the steering column under the plastic cover. It is removed by just pulling it toward the dashboard. The cover comes off simply with a couple of screws from underneath? Make certain all the bulbs are good!

I hope this helps,
Vinnie.

Jul 10, 2015 | Dodge Cars & Trucks

1 Answer

No hazard lights and no turn signals but every thing else works, HELP? I had a push button start installed the wire is connected into the blue fuse on the side wall just behind the battery, related?


the signals work off of the hazard flasher. the hazards are wired to constant power.if you run a fused wire from the hazard switch to the battery it all should work.
somehow the hazard power source got lost.check that there is not a blown fuse in the fuse box. a starter solenoid draws a good amount of current.they may have blown a small amp fuse looking for a power source.
patching into a fuse box for power is not high caliber work.

Mar 15, 2015 | 1994 Nissan Pickup

1 Answer

Hazard lights keep flashing once the engine has stopped


turn them off by pushing the button with the litte triangle next to the shifter

Mar 07, 2014 | 2005 Renault Scenic 1.9

2 Answers

I have a 2005 and the hazard lights keep flashing, I don't know what to do.?


The hazard lights are only a connection of all indicator lights through the hazard light switch on the dash. Press the switch again and if there are no other problems the lights will return to the indicators only

Oct 16, 2013 | BMW Cars & Trucks

1 Answer

Where can i locate the indicator relay on a impreza 1994


Put hazard lights on & follow the clicking

Jun 13, 2013 | Cars & Trucks

1 Answer

Where`s the switch to activate hazard lights ? cannot find


Don't know what type of vehicle this is, most of the time the sw. is located on the steering column.

Mar 05, 2013 | 2005 Subaru Impreza

2 Answers

No hazard lights


Check the hazard switch and the connector to hazard switch see if u have the power and earth to hazard switch if there is power and earth to switch then replace ur hazard switch its faulty but if there is no power and earth to switch then it has whirring problem

Jun 16, 2009 | 1997 Mitsubishi Mirage

2 Answers

1997 Subaru Impreza wagon. Just replaced battery and hazard lights are blinking whether ignition is on or off. Tried turning hazards on and off and that didn't stop it. Only removing battery stops it. ...


Under your dash by steering column,by your left knee, is a small 4" x4" box that has a small wire attached. On the end of the wire is a small button. Push the button with the ignition in the on position. It will reset the alarm system. That will stop your lights from flashing. Have a great day.

Jun 14, 2009 | 1997 Subaru Legacy

1 Answer

Hazard relay/resistor?


i have the exact problem, someone told me it could be one of the resistors or relays

Sep 13, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
2000 Subaru Forester Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...