Question about 1999 Ford Expedition

1 Answer

Installing chrome dash gauge bezel

How do you remove the plastic dash panel in front of the gauge lens,i took off all the screws and the headleght switch cover but I couldn't pull it off to install the gauge bezel,can you help

Posted by on

1 Answer

After you take the screws out you have to pull it and there are sone tabs that you have to push in.2 on top and 2 on bottom

Posted on Sep 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I install the exterior front door handle?


Take out inner door handle bezel-1 philips screw. Then remove 2 large screws under inner door handle. The lower light lens can then be removed exposing 2 small philips screws. Remove those and take out light assy and unplug. Use a screwdriver to pry gently on window-lock control switch assy. Remove and unplug. Then gently pry inner door panel off. The inner door handle and cables can be moves by sliding plastic assy back and out. Then you can remove the plastic rainliner exposing the door handle assy. 2 10mm bolts hold it in. Theres also to rods to remove by releasing clips and sliding rods out.

Feb 11, 2015 | 2004 Mitsubishi Endeavor

1 Answer

How do I remove dash covers to clean gauge faces?


I will need to know what it is you are working on.But usually in the top of the bezel (clear part in front of guages) there are 2 screws either Phillips or torques head.Then below steering wheel there is a wide panel and generally there are screws that will need be extracted.These are a bit hidden so remove the panel and look for those.

Oct 07, 2014 | 1998 Mercury Grand Marquis

1 Answer

How do I remove the driver side door panel on a 1994 Lincoln Mark VIII


Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Aug 16, 2014 | 1994 Lincoln Mark VIII

1 Answer

My Dash Isnt working, the gauges dont move or work how do i fix it


Instrument Cluster -it could be a loose connection at the harness. REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Disable the SIR system. Refer to procedure outlined in this section.
  3. Remove the cluster trim plate, as follows. Fig. 1: View of the cluster trim plate (1), instrument panel (2), dimmer switch lead (3), fog lamp switch (4), and mounting screws (5) - Chevrolet Malibu shown 93206g21.gif
    Fig. 2: View of the cluster trim plate screws (1), cluster trim plate (2), and instrument panel assembly (3) - Oldsmobile Cutlass shown 93206g22.gif
    1. Remove the bezel from the ignition switch. Fig. 3: Remove the bezel from the ignition switch 93206p24.jpg

    2. Remove the screws fastening the cluster trim plate.
    3. Gently pry out the trim plate.
    4. Detach the hazard and instrument panel electrical connectors and remove the trim plate.
  4. Remove the four screws attaching the instrument cluster to the dash panel.
  5. Pull the cluster rearward and detach the electrical connections, then remove the cluster from the vehicle. Fig. 4: Exploded view of the instrument cluster assembly 93206g23.gif
    To install:
  6. Attach the cluster electrical connectors and position the cluster into the instrument panel recess.
  7. Install the screws into the instrument cluster and dash. Tighten the screws until fully driven, seated, not stripped.
  8. Install the cluster trim plate, using the reverse of the removal procedure.
  9. Enable the SIR system as outlined in this section.
  10. Connect the negative battery cable.
prev.gif next.gif

Nov 09, 2010 | 2001 Chevrolet Malibu

1 Answer

Window on drivers side froze and fell down and won't roll back up. How to take door panel off to fix the window


  1. Disconnect the negative battery cable. Important: When removing a door trim panel or switch plate, disconnect the negative battery terminal. This will eliminate the possibility of shorting out the switch if you use a screwdriver, an awl, or other metal object in order to remove the switch from the harness.
  2. Remove the window regulator handle, if equipped.
  3. Remove the front door warning reflector.
  4. Remove the door panel screw (1) through the hole in the door warning reflector opening.
  5. Use a flat bladed tool in order to remove the rear deck release switch bezel.
  6. Disconnect the rear deck release switch.
  7. Use a flat-bladed tool in order to remove the lower switch bezel trim screw access cover.
  8. Remove the lower switch bezel trim screws.
  9. Remove the lower switch bezel
  10. Use a flat-bladed tool in order to pry the front door switch bezel upward.
  11. Disconnect:
  1. Gently disengage the front door trim retaining clips and remove the door trim panel from the door.
Installation Procedure




  1. Install the front door trim panel to the door. Ensure that the retainers are locked into place.
  2. Connect the rear deck release connector.
  3. Install the rear deck release switch bezel. Press the bezel firmly into place.
  4. Install the window regulator handle to the door.
  5. Connect:
  1. Install the front door switch bezel assembly to the front door trim panel.
  2. Install the lower switch bezel trim panel. Notice: Refer to Fastener Notice in Service Precautions.
  3. Install the lower switch bezel trim screws.
  4. Install the lower switch bezel trim screw access cover.
  5. Install the door trim panel screw (1) through the hole in the front door warning reflector.
  6. Install the front door warning reflector.
  7. Connect the negative battery cable.

Oct 15, 2010 | 2000 Oldsmobile Alero

1 Answer

Replacement of speedometer on 1988 F150 V6 5 Speed


Easiest to just get a new gauge cluster -

Remove the dash bezel (some screws/clips), then remove the 4-5 screws that hold the cluster in (can't remember exactly how many). Pull the gauge panel partially out, remove wires and detach speedo cable.

Installation is the reverse of removal.

Aug 10, 2010 | 1988 Ford F 150

1 Answer

How do I replace the passenger side corner light and front side turn signal light?


Front Turn Signal & Parking Lights


7ccc73e.gif
Remove the 2 parking light housing retaining screws ...


9898a80.gif
... then pull the housing away from the vehicle far enough to remove the bulb socket from behind the housing. Turn the socket counterclockwise and pull


a323ae9.gif
Push the bulb in the socket gently and turn clockwise, then pull the bulb out of the socket. Note the offset retaining ears on each side of the bulb


  1. Remove the screws from the lens and separate the lens from the headlight bezel.
  2. Remove the headlight bezel.
  3. Remove the screws from the turn signal housing and pull it out.
  4. Turn the bulb socket counterclockwise 1/3 turn and remove it.
  5. Installation is the reverse of removal.


Side Marker Lights
  1. Remove the screws from the marker lens and separate the lens from the headlight bezel.
  2. Pull the bulb from its socket in the back of the lens.
  3. Installation is the reverse of removal.

Feb 14, 2010 | 1997 Jeep Grand Cherokee

1 Answer

How do you take out the radio


Disconnect the negative battery terminal to prevent an
accidental short circuit. Remove the plastic trim piece to
the left of the glove box and (1) phillips screw exposed.
Unsnap the top edge of the knee bolster panel. Remove
(1) phillips screw from the panel. Remove the ashtray
cluster and (2) phillips screws from each side. Unclip the
entire dash trim bezel and remove.Open doors and
unsnap end caps from each side of dash. Unsnap and
remove radio/instrument cluster panel. Remove (3)
screws in order to remove radio.
Disconnect the negative battery terminal to prevent an
accidental short circuit. Unsnap and remove dash bezel.
Remove (3) 9/32" screws and remove radio.
1
BUICK Rendevous 2002-2007

Feb 11, 2010 | 2002 Buick Regal

1 Answer

Can you please describe how to install a cd player in a 96 Hyundai Elantra?


Disconnect the negative battery terminal to prevent
an accidental short circuit. Pop out the dimmer
switch panel and remove (1) Phillips screw
exposed. Unsnap the gear shifter trim plate and
remove (1) Phillips screw exposed at the base of
the dash trim bezel. Reach under the driver's
side dash, locate the temperature control cable
and remove the cable from the white plastic
bracket. Position the gear shifter in low, pull the
dash panel away and disconnect all wiring harnesses.
Remove the trim bezel (the temperature
controlcable will be attached). Remove (4)
Phillips screws securing the factory head unit
and disconnect the wiring.

Feb 07, 2010 | Hyundai Motor 1996 Elantra

1 Answer

Dashboard Gauge


  1. Disconnect and isolate the battery negative cable.
  2. Remove Over Steering Column Bezel Replacement.
  3. Remove over steering column bezel.
  4. Remove left end cover.
  5. Remove screw at left end of cluster bezel and headlamp switch.
  6. Remove screws holding cluster bezel to instrument panel from each side of steering column.
  7. Disconnect clip holding cluster bezel to instrument panel from above right vent louver.
    1. Separate cluster bezel from instrument panel.
    2. Disconnect wire connectors from back of the bezel.
    INSTALLATION
    1. Connect wire connectors into back of the bezel.
    2. Place cluster bezel in position on instrument panel. Use care not to place hands on louvers.
    3. Connect clips to hold cluster bezel to instrument panel. Use care not to add pressure on the A/C louvers to seat the cluster bezel clips.
    4. Install screws to hold cluster bezel to instrument panel on each side of steering column.
    5. Install screw at left end of cluster bezel and headlamp switch.
    6. Install left end cover.
    7. Install over steering column bezel.
    8. Install lower steering column cover.

    I wouldnt Recomend This Procedure To Anyone juse for Cleaning Purposes Unless Your VIEW OF IT IS "SERIOUSYL IMPARED IF it Moisture Has Accumilated Behind Face of it Then Find Out WHY and Resolve THAT PROBLEM FIRST Onherwise Here you Are. Have A Great DAY !! And Please Dont forget to RATE Me Thank You !

Jan 15, 2009 | 1999 Dodge Caravan

Not finding what you are looking for?
1999 Ford Expedition Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...