Question about 1998 Mercedes-Benz E-Class

1 Answer

Air Conditioner for Benz 1998 E320

I have noticed that cool air started coming from the central vents that are located on the top side of the compartment and also from right and left side vents. Also air coming is not cool enough.

Posted by on

  • mmoran5555 Dec 31, 2008

    The left air vents' temperature is hotter than the right vents' temperature on a 1998 Mercedes Benz E320

  • Anonymous Mar 30, 2014

    Chemical smell inside card when first starting air conditioning. Now comes on in the Economy mode only.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 409 Answers

Check system for codes;

Displaying & Reading Trouble Codes (DTC Memory)
Air Conditioning (A/C) 

Models 208 as of MY 1998

Diagnostic trouble Code Memory [15] 

Note: 

  • The A/C pushbutton control module (N22) has DTC memory and data output. The diagnostic trouble codes and data are displayed via the temperature display window. The stored DTC's will remain in memory even with the vehicle battery disconnected.
  • The DTC memory differentiates between current and intermittent faults.
  • Numerous DTC's can also be read with the Hand-Held Tester (HHT).

Preparations for DTC Readout 

  1. Review 11, 12, 13, 14, 15, 21, 22, 31, 31, 41
  2. Ignition: ON
  3. Temperature selector: left: "HI"; right: "LO"
  4. Ignition: OFF
  5. Ignition: ON
  6. Within 20 seconds press REST and EC simultaneously for more than 5 seconds.
  7. The LED in Recirculated Air flashes and the display shows "d1A".
  8. Press AUTO repeatedly until all DTC's are displayed. Record each DTC as it is displayed.
  9. Each fault (short circuit, open circuit) is assigned a DTC. Thus in the left display: "E1" appears, and the right display indicates the DTC. The current faults (refer to table) are displayed first, next, the intermittant failures (e.g. 45 °5) are displayed in the display window next to the FAN symbol. By pressing the right AUTO the next DTC is displayed.
  10. To erase: Can only be performed after all faults have been readout. Press left AUTO and right AUTO buttons simultaneously for more than 2 seconds and the display shows: left: "d" and right: "FF". To cancel erase: By pressing the left AUTO button, the current faults will appear again.
  11. Select a base temperature setting.
  12. Turn ignition OFF, to end test.
Note: Due to instrument cluster (IC) series interface, DTC's may be stored in IC memory, therefore readout and erase DTC's from IC memory.

Air Conditioner for Benz 1998 E320 - 133090425133090426

Posted on Dec 30, 2008

  • John Weathers
    John Weathers Dec 30, 2008

    If you pull up the codes get back to me and I will tell you what they are.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many airbag sensors in a 2008 gmc acadia


1) Front End Sensor - Right--Located under the front hood in the engine compartment (2) I/P Air Bag--Located at the top right under the instrument panel (3) Roof Rail Air Bag - Right--Located under the headliner, extending from the passenger front windshield pillar to the passenger rear windshield pillar (4) Side Impact Sensor (SIS) - RF--Located under the right front door trim near the lower rear of the door frame (5) Sensing and Diagnostic Module (SDM)--Located underneath the vehicle carpet under the center console (6) Seat Belt Pretensioner - RF--Located under the trim near the bottom of the center pillar (7) Side Impact Sensor (SIS) - RR--Located under the right rear door trim near the lower rear of the door frame (8) Roof Rail Module - Right--Located behind the garnish molding on the upper rear pillar (9) Roof Rail Module - Left--Located behind garnish molding on the upper rear pillar (10) Side Impact Sensor (SIS) - LR--Located under the left rear door trim near the lower rear of the door frame (11) Seat Belt Pretensioner - LF--Located under the trim near the bottom of the center pillar (12) Side Impact Sensor (SIS) - LF--Located under the left front door trim near the lower rear of the door frame (13) Roof Rail Air Bag - Left--Located under the headliner, extending from the driver front windshield pillar to the driver rear windshield pillar (14) Steering Wheel Air Bag--Located on the steering wheel (15) Vehicle Battery--Located at the front left of the engine compartment. (16) Front End Sensor - Left--Located under the front hood in the engine compartment

Aug 12, 2015 | GMC Cars & Trucks

1 Answer

I have a 2010 Chevy Equinox. The air vents in the vehicle all work except for the drivers side right vent ( to the left of the radio and to the right of the driver ). All vents were working but it seems as...


The exhaust inside the car would suggest the vents in question have fallen apart somewhere in the dash between the engine compartment and the interior allowing fumes to enter the cabin. Get that checked at a garage right away. Very dangerous to breath exhaust fumes.

May 18, 2014 | Cars & Trucks

1 Answer

How do you remove dashboard on a 2002 senta


Open the top compartment and grab the inside of that compartment. Pull that and the compartment and the vents will come towards you and out. There are wires attached, set the compartment up on the dash with out stretching the wires too far.
There are two philips screws that you need to remove. One is on the bottom left hand corner of the left vent, and the other is on the bottom right hand side of the right vent.
Grab the radio and pull, the bottom plastic bezel will fall out. Set that aside.
There are two more philips screws. One on the bottom left hand corner of the heater controls, and the other is on the bottom right hand side of the heater controls.
You can now pull out your radio. There is a plug on the backside of the radio and you will need to unplug that.
Good luck!

Jan 09, 2012 | Nissan Sentra Cars & Trucks

2 Answers

I have a 1993 VW Passat VR6, My problem is when I try to start it, I have no spark from the spark plugs..What could be the problem or how do I fix this?????


GO TO THIS SiTE TO CHECK THE FUSE BOX!
http://vwtech.no-ip.info/images/golf/post90.gif

This are the FUSE and RELAY number SLOT!
Fuse No. Description Ampere Rating 1 Headlight, low beam, left 10 2 Headlight, low beam, right 10 3 Instrument panel lights, license plate lights 10 4 Glove compartment light 15 5 Wiper/washer 15 6 Fresh air blower 16-valve only: Air conditioning 20 7 Taillights, side marker light, right 10 8 Taillights, side marker light, left 0 9 Rear window defogger 20 10 2.0 16-valve only: Fog lights 15 11 Headlight, high beam, left,High beam indicator light 10 12 Headlight, high beam, right 10 13 Horn 16-valve only: Radiator cooling fan 10 14 Back-up lights, washer nozzle heaters 10 15 2.0 16-valve only: Engine electronics, stabilizer valve, cold start valve 10 16 Instrument panel warning lights, 16-valve only: Multi function indicator 15 17 Emergency flasher switch, turn signals 10 18 Fuel pump, oxygen sensor heater 20 19 Radiator cooling fan, air conditioning 30 20 Brake lights, cruise control 10 21 Interior lights, digital clock 16-valve only: Luggage compartment light,multi function indicator, central locking 15 22 Radio, cigarette lighter 10
Relays Relay No. Description 1 Air conditioning 2 Open 3 Digifant control unit 4 Load reduction relay 5 Low coolant level control unit or Open 6 Emergency flashers 7 Rear Wiper 8 Intermittent wipers 9 Seat belt warning system control unit (possibly headlight warning too?) 10 Fog lights 11 Horn 12 Fuel pump (except diesel)Glow plugs (diesel) 13 Radiator cooling fan after run (except 16-valve)2.0 16-valve: Starter interlock relay 14 Automatic trans., coolant temperature indicator,starter interlock relay (except 2.0 16-valve)2.0 16-valve: Radiator cooling fan after run 15 ABS pump relay 16 ABS relay 17 Heated seat control unit, driver 18 Heated seat control unit, passenger, or power seat circuit breaker 19 Automatic transmission 20 Open 21 Power window relay, ABS hydraulic pump fuse 22 ABS valves fuse 23 Air conditioning, power seat fuse 24 Power window fuse

Nov 17, 2010 | 1993 Volkswagen Passat

1 Answer

Where is the cabin air filter located at and how do i get to it.


It will either be behind your glove box, or will be located under your hood by the firewall.

    Behind the Glove Compartment
  1. Open the glove compartment and remove all the items from inside of it.
  2. Remove the glove compartment assembly retainer screws with a Phillips head screwdriver. Refer to the repair manual for your specific year and model series BMW for the exact location of the screws or carefully look around the perimeter of the interior glove box assembly to locate the screws.
  3. Locate the lower trim panel retaining screws behind the glove box assembly. Remove the screws with a Phillips head screwdriver and then remove the panel.
  4. Remove the foot-well air duct.
  5. Loosen the retaining screws of the control module box to all you to lower it down.
  6. Turn the cabin air filter panel retaining knob counterclockwise to open the panel. Pull the filter removal tab outward to remove the filter.
  7. Use a shop vac to clean out any noticeable debris from the cabin air filter housing interior.
  8. Insert the new filter and reverse the order to reassemble the foot-well air duct, the trim panel and the glove compartment assembly.
  9. Under the Hood
  10. Open the hood and locate the cabin air filter housing. The housing is located near the cowling on the top section of the firewall. Some models place the housing in the middle of the cowling, on both sides--left and right--of the cowling or on the passenger side cowling. Removal of the cowling and placing the windshield wipers in the upward position may also be required on certain models. Some 7-Series BMWs place the filter housings on both the left and right side undercarriage of the hood.
  11. Release the cabin air filter duct clamp. This can either be released by unclipping the air filter duct by pressing a retaining lock with your fingers or using a flathead screwdriver to pry off a retaining rod.
  12. Lift the cover upward--or downward on hood-installed 7-Series BMWs--to reveal the cabin air filter.
  13. Remove the cabin air filter from the air duct. Vacuum the air duct with a shop vac.
  14. Insert the new cabin air filter(s) and reassemble.

Oct 16, 2009 | 1993 BMW 7 Series

1 Answer

This car has the automatic temperature control system


The hot/cold switch is probably bad.you have a blend door box that opens to let the cold air in and closes to let the hot air in.From what you are saying this part is no responding to the switch movement.Make sure power is at the switch and power should go through the switch when put on cold air this moves the blend door.Some times the blend door goes bad and has to be replaced its under the dash on the right side.

Aug 10, 2009 | 1999 Mercury Grand Marquis

1 Answer

WHERE IS THE AIR FILTER LOCATED


The intake air filter is located under the hood on the right side ( a black tube leading to a black box which the filter is in). the cabin air filter is behind the glove compartment, just unscrew the one screw on the right of the glove compartment which holds the linkage and remove the two black tabs on each side of the inside of the glove compartment, to do this simply turn and pull each tab ( a little plier may be useful because they may be kinda tight). the glove compartment should now fall freely. behind it is a white tray which holds the air filter, simply pull it out and clean it or replace it, HINT...the funky smell that comes out of your air vents is usually caused by a dirty cabin air filter

Jul 28, 2009 | 2002 Lexus ES 300

1 Answer

A/C issue with 99 Grand Prix


Check the ac filter, it might be dirty and thats why it is not blowing out enought cold air. The filter is located under the wiper cover but behind the firewall on the passengers side. You access this by lifting the hood and removing the rubber type gasket that holds both together, right on top of the blower unit.

Apr 24, 2009 | 1999 Pontiac Grand Prix

1 Answer

No air flow through 4 top rear vents


Don't worry, it's designed that way. The owner's manual is pretty unclear about this. But the heated air only comes out the floor vents underneath the front seats and the "heat vents" at the forward and side of the rear A/C compartment near the floor. The cooled or vent air flows from the overhead vents.

Nov 28, 2008 | 2004 Honda Odyssey

1 Answer

Ford F150 AC Problem


there is a vent opening linkage for the top vents if you had removed panel for sterio install this linkage might have come loose or the wiren to electric relay to open top vents came loose

also vent doors on front of a/c vents are turned to the closed position

also quite possible the passenger blower motor compartment door in side the blower mode has something blocking entrance

also your truck might be equiped with a blower motor filter i read that these need to be changed out during normal filter replacements the filters for ford i didnt know they started using filters for a/c on reading this since 2000

May 31, 2008 | 2003 Ford F150 Regular Cab

Not finding what you are looking for?
1998 Mercedes-Benz E-Class Logo

1,161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

164 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...