Question about 1993 Chevrolet K1500

1 Answer

Clutch replacement need info on remove trans and replacing clutch

Posted by on

  • Anonymous Jan 03, 2009

    how to replace clutch

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,674 Answers

This link may help. Check proper vehicle & 4WD ?

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008f40a

Posted on Feb 13, 2009

2 Suggested Answers

  • 1 Answer

SOURCE: need clutch replacement directions for Ford Ranger

Remove drive shaft,remove crossmember under transmission.Remove transmission and diconnect linkage.Remove bell housing,and clutch berring assembely.Remove bolts on pressure plate.Once this is done.Remove fly wheel for machineing.you will need a pilot shaft to alighn clutch assemblely.Possible one will come with new clutch and pressure plate.Reverse assemblely in same order remember to torque all your bolts with torque wrench.Take your time.

Posted on Apr 19, 2009

inkedsgt
  • 359 Answers

SOURCE: 86 Samurai when removing the trans to replace the clutch,

yes

Posted on Nov 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace a flywheel on a 87 ford f150 4x4 manual trans.Need to know what I need to take off to get to flywheel


everything attached to trans and pull trans out, remove clutch assy, replace flywheel, if clutch is worn, replace it as well, do not use rebuilt clutch parts they will not last,

Aug 31, 2013 | Cars & Trucks

1 Answer

Need to change clutch on mgzt


jack up engine loosen trans from engine pull trans back to access the clutch assembly remove fly wheel remove clutch pressure plate and replace reassemble be careful

Jun 27, 2012 | Cars & Trucks

1 Answer

How to replace clutch


are you sure the clutch is bad or is it a hydraulic issue dose the pedal fall to floor after a while stoped or does it slip whil under a load you need to remove tranaxel to replace clutch preasure plate and throw out bearing as well as resurface flywheel check rear main seal andpossibly replace pilot bearing or bushing if it is hydraulic trans axle can stay in and just change slave cyl and or clutch master cyl

Mar 25, 2012 | 1995 Ford Escort

1 Answer

I need detailed instructions on how to replace the clutch on a 1987 Ford Bronco II, 4wd, manual trans, 6 cyl. Can you tell me where I might find this information online?


It is a copyright infringement to give info copied from a book ,unless you pay for it...I can tell you the fnt end of truck needs to be jacked up so you have plenty of room for repair.also if fluids are drained from trans and transfer case they will be able to handle better...
remove fnt and rear drive shafts and trans shift linkage . also the transfer case linkage . the speedo cable and wirig to trans will need to come off....now support the trans with a floorjack and remove the crossmember support... let the jack down a little to acess to top trans to engine bolts. thenremove all bolt except 2 ...one on each side take the bolts out of clutch slave cylinder and move away from your work...reposition jack to the center of trns and remove trans carfully.one hand on trans tail shaft and one on the jack handle. lower trans assembly to the ground after you have cleared the clutch..now follow instructions in new clutch and reinstall ...

Feb 17, 2011 | Ford Bronco II Cars & Trucks

1 Answer

How do i install a clutch on a 1990 laser?


You need to get a manual. Try the Haynes manual for your car. Try autozone; generally available for around $20. This is not the type of thing that can be covered here in enought detail to do you any good.
Basics are;
disconect the negative battery cable, set parking brake
locate the trans mounting bolts
get something to support the engine and something to support the trans
seperate the trans from the motor by removing the bolts. On transverse mounted engines you will probably have to pull the trans to get enough room to remove the clutch and you'll probably have to remove the 1/2 shaft axles (front wheel cars) or drive shaft (rear wheel drive cars)
If replacing the entire clutc assembly (pressure plate, flywheel, and clutch), loosen the pressure plate mounting bolts gradually working your way around the pressure plate. If only replacing the clutch then seperate the sperate the pressure plate from the flywheel and remobe. Align clutch with a clutch allignment tools and replace pressure plate. Torque bolts to spec. reconnect the trans to the motor. Few other things to think about. You should replace the throwout bearng when doing a clutch. Lube the clutch fork as directed without getting lub on the clutch face. Hopefully I have convinced yu to get a manual or you will be hating life if you take this on without it.



Feb 21, 2010 | 1990 Plymouth Laser

1 Answer

How do you remove the bearing from clutch slave 91 f150 2wd 5 speed


it is probably best if you go to the library and find the info on ckutch replacement,so you can see it there is a clip affair to release the slave cylinder the bearing for the clutch fork is only accrsable after remouving the trans and the bell housing.

Feb 14, 2010 | 1991 Ford F150

1 Answer

Need to replace clutch


hands down the trans...under optimal conditions I have done this repair in under an hour. If you were to remove the engine for this repair you are going to struggle aligning the input shaft from trans into new clutch plate when re-assembling. The trans is so light weight a jack is not entirely needed at all and no fluids, coolant or oil would have to be drained as well.If the exhaust Y pipe comes down without any bolt removal problems ,you are basically home free but do remeber to drive out the roll pins in the DOJ (transmission side axle joint)

Jun 28, 2009 | 1992 Subaru Legacy

1 Answer

DOES ENGINE HAVE TO BE REMOVED TO REPLACE CLUTCH. HOW DO I ID CAR AS A SW1 VS SW2?


Trans has to be either removed or unbolted & moved away from engine 3" or more to gain access to clutch assy.If you remove trans all the way Cradle needs to be removed & engine supported with special tool.Big Job On the ground!!

May 05, 2009 | Saturn SW Cars & Trucks

1 Answer

Need clutch replacement directions for Ford Ranger


Remove drive shaft,remove crossmember under transmission.Remove transmission and diconnect linkage.Remove bell housing,and clutch berring assembely.Remove bolts on pressure plate.Once this is done.Remove fly wheel for machineing.you will need a pilot shaft to alighn clutch assemblely.Possible one will come with new clutch and pressure plate.Reverse assemblely in same order remember to torque all your bolts with torque wrench.Take your time.

Apr 19, 2009 | 1994 Ford Ranger Supercab

2 Answers

Clutch Replacement


I just checked my AllData repair info. It does not mention removing the engine to replace the clutch. It does say that you'll have to support the engine to remove the transaxle. If done on jack stands, this is easily done with a floor jack and block of wood under the engine's oil pan.
Charlie

Jun 25, 2008 | 1993 Saturn SL1

Not finding what you are looking for?
1993 Chevrolet K1500 Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...