Question about 1999 Suzuki Vitara

2 Answers

Suzuki Vitara 1996 V6 2L assembly problems

Enjin completely disassembled, would like to know how to lign up timming marks for all 4 cams and crank shaft. also torque settings for bearings and head bolts.

Posted by on

  • 2 more comments 
  • rival501 Dec 27, 2008

    same problem please help me on how to set the timing marks on my vitara v6 1996. H20A.

  • Anonymous Feb 07, 2009

    i need timing mark for timing change

  • Anonymous Mar 24, 2014

    enjin afx motor busy to overhaul enjin.Thanks

  • Anonymous Mar 28, 2014

    need timming mark

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The suzukiinfo.com site has a whole heap of free genuine manuals you can download and print out.
www.suzukiinfo.com

Posted on Jan 22, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thank you Mmoz 74 :)

Posted on Jan 22, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timming belt diagram


  • G16B (16valve is here)
http://www.fixkick.com/t-belt/16-fast-belt-install.html

note false timing marks on the cam cog wheel.
do not mess that up.

this page even has the FSM pages, to read. on G16B



Mar 06, 2015 | 1999 Suzuki Vitara

1 Answer

How to remove and install timing chain on a 1999 1.6 4 cylinder Suzuki Vitara ?


no less than? G16B engines 1992 to max. (usa)
the suzuki FSM covers this, buy one.?
  1. Alldata.com to, log in and read. (google that, it's a #1 site)
  2. or at suzuki pit stop plus. https://suzukipitstopplus.com/Products/1037-1999-vitara-grand-vitara-service-manual.aspx
  3. $4 to look there.
  4. if you buy the Gates belt? and read the sheet in the box !
  5. or here. FREE.
  6. http://www.fixkick.com/t-belt/16-fast-belt-install.html
if , M/T tranny ,no special tools are needed.

watch out for false cam marks, seen in #6
Suzuki uses parts off another engine, and even fails to warn
you in the FSM , sad that.

FSM= the offical, factory service manual.. all cars have this.

Sep 07, 2014 | 1999 Suzuki Vitara

1 Answer

I NEED TO KNOW WHERE TIMMING MARKS ARE


I never owned a Suzuki bur every vehicle I have owned the timing marks where located on the harmonic balance wheel - that is the pulley attached to the end of the crankshaft., where drive belt runs from. I hope that helps. I suggest you get a shop manual fro AutoZone.

May 20, 2013 | 1999 Suzuki Vitara

1 Answer

Timming marks diagram for suzuki vitara v6 engine


get #1 piston on top dead center and exhaust cam so valves are closed ,get intake valves open

Jan 14, 2013 | 1999 Suzuki Vitara

1 Answer

I have a vitara jlx se 1.6i 16v and i have a problem starting it when u turn the key to start it the engine turns over fuel is gettig to plugs the plugs are sparking the timing is all spot on iv changed...


Sounds to me like your dizzy is 180 degrees out.
Too explain: Suzuki does things oddly... the timing marks on the cam sprocket line up when #4 is ready to fire. But then they have you time the distributor to #1. to get it ready for #1 to fire you need to turn the crank one turn. This oddity causes many others to have your issue. So you can check... If you line up the marks on the cam, the dizzy rotor should be pointing at the wire going to #4.

Dec 19, 2011 | Suzuki Vitara Cars & Trucks

3 Answers

Could you let me know where the timing marks are for a Suzuki Grand Vitara 1.9 DDiS


check around the inside (towards the block) edge or crank shaft pulley by the lower passenger side of the engine. Otherwise it will be by that pulley on the bloc, those are the only laces I've known them to be. Hope it helps

Jun 07, 2010 | 2007 Suzuki Grand Vitara 4WD

1 Answer

I removed the timming belt of a fiat uno 1983-1985 with out setting it to TDC I know where the cam pully and its mark are on the enjin but can not find the crank pullys mark on the enjin to set it to TDC...


PULL OUT NO 1 SPARK PLUG PUT A SCREW DRIVER DOWN THE HOLE AND TURN THE ENGINE OVER BY HAND UNTIL THE SCREW DRIVER IS AT THE TOP THEN YO WILL SEE THE MARKS ON THE CRANK OR LOOK AT THE TIMMING COVER IT SHOULD SHOW YOU TDC

Aug 30, 2009 | Fiat X1/9 Cars & Trucks

1 Answer

I need to know how to set the timming marks on the 1.6 double over head cams to replace timming belt


timming marks on cams face each other 3 and 9 o clock crank mark at about 6 o clock mark in cover and sump auto adjuster arrow should be in v mark to set this requires turning water pump by loosening water pump bolts slightly be warned some times this causes pump o ring seal to leak if turning.

May 19, 2009 | 2000 Daewoo Lanos

2 Answers

Timming problems


4 cylinder or v-6? Try and get the book on your vehicle and follow the instructions. Haynes Manual #47017 Worked for me...

Aug 21, 2008 | 1996 Isuzu Rodeo

Not finding what you are looking for?
1999 Suzuki Vitara Logo

887 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

63456 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...