Question about 2000 BMW 7 Series

2 Answers

Trouble codes p0011 and p0021

Car runs fine,but when at idle it idles a litle up and down specially with the ac on

Posted by on

2 Answers

IT HAPPENED THAT SOMEBODY CHANGED THE CLUTCH AND THE FLYWHEEL AND INSTALLED THE WRONG FLYWHEEL AFTER WE INSTALLED A NEW FLYWHEEL THE PROBLEM WAS GONE.BUT THANKS ANYWAY.


ATT.:RAMON JIMENEZ

Posted on Oct 12, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 231 Answers

Have your timing checked as these codes suggest that you are advanced on one bank and retarded on the other bank, also have your coil pack tested. as for surging up and down while the a/c is on this is normal.

Posted on Oct 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

As soon as I turn my AC on the motor runs rough and when I turn it off it runs on 8 cylinders perfectly fine, I Check the harness for opens or a short to ground I still haven't found the fan relay


What is year--make--model?
How long since a tune-up? Any applicable trouble codes? Some of the national brand auto stores will check codes for free. I always check for codes, don't care if the cel is on or not.
Some makes and models, if you turn on the ac, the pcm will try to up the idle, so as not to cause idle issues.
Clean the throttle body, check and clean idle air system, see if it helps?

Mar 27, 2016 | AC Cars & Trucks

1 Answer

Code p0011 2006 chevy impala: camshaft position actuator


You can read all about your code here:
http://www.obd-codes.com/p0011

Most likely a P0011 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.

Jul 10, 2015 | 2006 Chevrolet Impala

1 Answer

How to fix fault p0021 and engine failsafe program


(powertrain control module, also called an ECM). That consists of a few different components but the P0021 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft. A P0021 engine code is basically the same as a P0011 code, except this is for Bank 2, not Bank 1.
Symptoms Possible sumptoms of OBD code P0021
Most likely a P0021 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.
Causes Possible causes of OBD code P0021
A P0021 DTC trouble code may be caused by one or more of the following:
Possible Solutions This DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.

Jan 24, 2015 | 2008 Land Rover Range Rover

1 Answer

Codes on my cayanne p0011 and p0021


Well code 11 is for a problem with the cam sensor signal on bank one and code 21 is the same issue with the sensor on bank two.
Its possible the timing belt has jumped.

Jan 15, 2014 | Cars & Trucks

1 Answer

Code p0011


http://www.datsc.com/tabid/122/OBD-Error-Code/P0011/Diagnostics/Mercedes-Benz/Default.aspx
"..........OBD Code P0011refers to
A code P0011 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0011 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft.

SymptomsPossible sumptoms of OBD code P0011
Most likely a P0011 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.

CausesPossible causes of OBD code P0011
A P0011 DTC trouble code may be caused by one or more of the following: Incorrect camshaft timing Wiring problems (harness/wiring) in intake timing control valve control solenoid system Continuous oil flow to VCT piston chamber Failed timing valve control solenoid (stuck open)

Possible SolutionsThis DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.

Related CodesP0010 P0012 P0020 P0021 P0022..........."

Oct 04, 2013 | Mercedes-Benz Cars & Trucks

1 Answer

Fault code P0021


Hi there:P0021 - "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

A code P0021 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0021 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft. A P0021 engine code is basically the same as a P0011 code, except this is for Bank 2, not Bank 1.

Most likely a P0021 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.


A P0021 DTC trouble code may be caused by one or more of the following:Incorrect camshaft timingWiring problems (harness/wiring) in intake timing control valve control solenoid systemContinuous oil flow to VCT piston chamberFailed timing valve control solenoid (stuck open)

Possible Solutions:This DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.To reset the fuel pump, press the button on the switch. The switch is located immediately below the hole in the trunk side trim.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa.

Mar 06, 2012 | Cars & Trucks

1 Answer

03 Maxima SE... Check engine light is on and getting codes P0011 AND P0021 which is the intake camshaft position timing over. I also have P0462 because my fuel level sensor always reads as full and while...


Hi there Camilo:
DTC P0011 - "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)
A code P0011 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0011 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft.
Potential Symptoms

Most likely a DTC P0011 will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.
Causes

A DTC P0011 trouble code may be caused by one or more of the following:
- Incorrect camshaft timing
- Wiring problems (harness/wiring) in intake timing control valve control solenoid system
- Continuous oil flow to VCT piston chamber
- Failed timing valve control solenoid (stuck open)

Possible Solutions:
This DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.

Other related DTCs: P0010 - P0011 - P0012 - P0020 - P0021 - P0022
----------------------------------------------------------------------------------------------------------------

DTC P0462 - Fuel Level Sensor Circuit Low
This could happen happen you ran your fuel tank too low I would first fill up the tank and go to your local parts store and have them reset the code to see if it stays off .If the light comes back on the most likely reason is because the fuel level sensor needs to be replaced but other possible causes are wiring problems, fuel pump module, or cluster. You will need to barrow a special tool which is the lock wring wrench from your local parts store to remoe the fuel pump. Here are instructions from Nissan TSB (Technical Service Bulletin) to solve it; let me know if you have questions.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jan 31, 2012 | 2003 Nissan Maxima

4 Answers

Codes p0011 and p0021


P0011 "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)
P0021 "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

Oct 10, 2011 | 2004 Ford F150

1 Answer

I recently changed my timing chain tensioners on my 2005 Altima VQ35 and now I get the P0011 and P0021 codes. I've reset them and changed the oil but they keep coming back. I need to smog my car within the...


You got two codes for Timing Over
Advanced

P0011-Bank 1
P0021-Bank 2

I'am assuming you know that

Cams moved, I would think,
when you did tensioners !!

Or , you have to reset the sensors,
of which I don't know your system

Feb 23, 2011 | Nissan Altima Cars & Trucks

1 Answer

Identified as P0011


P0011 - "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

What does that mean?
A code P0011 refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module, also called an ECM). That consists of a few different components but the P0011 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. The "A" camshaft is either the intake, left, or front camshaft.

Potential Symptoms:
Most likely a P0011 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.

Causes:
A P0011 DTC trouble code may be caused by one or more of the following:
* Incorrect camshaft timing
* Wiring problems (harness/wiring) in intake timing control valve control solenoid system
* Continuous oil flow to VCT piston chamber
* Failed timing valve control solenoid (stuck open)

Possible Solutions:
This DTC code is a result of a mechanical fault of the VCT unit or related components, so there is no need for electrical diagnosis. Refer to vehicle specific repair manual to perform component tests for the VCT unit. Notes: Dealer techs have advanced tools and the ability to follow detailed troubleshooting steps, including the ability to test components using a scan tool.

Other related DTCs: P0010 - P0011 - P0012 - P0020 - P0021 - P0022

Hope helps (remember rated this).

Jun 25, 2010 | 2003 Nissan Altima

Not finding what you are looking for?
2000 BMW 7 Series Logo

Related Topics:

964 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Fred Sops

Level 2 Expert

271 Answers

Al Clark

Level 2 Expert

290 Answers

Doberman

Level 2 Expert

246 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...