Question about 1992 Honda Accord

1 Answer

92 Accord Buzzing Sound below Glove Box

There is a buzzing sound which appears to be below the glove box when I have the FRESH AIR or RECIRCULATION buttons turned on. If neither are turned on then the buzzing noise stops. Just wondering if this could be a faulty relay or something and where exactly it might be located?

Posted by on

  • billee12345 Aug 20, 2008

    It only happens if i have one of those buttons pressed though. I can still have the blower motor running without those engadged and the humming doesn't happen.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 53 Answers

Well that's where your ac blower motor is. you may have something wedged in it smacking the blades on the wheel or the bearings in the blower motor could be going out but that would making more of a hum or a grinding noise.

Posted on Aug 20, 2008

  • Daniel Thrash
    Daniel Thrash Aug 20, 2008

    well with that bit of information i can tell you that your air door is most likely hitting the blower when in that position

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace an air inlet actuator on 2007 Pontiac Vibe 1.8 Liter Engine


Recirculation Control The recirculation control determines the air intake through the recirculation actuator. When the recirculation switch is pressed, a signal is sent from the switch to the recirculation actuator through the recirculation signal circuit. When the actuator receives the signal, the actuator moves into the recirculation mode. This circulates air from inside the vehicle instead of fresh air from the outside. Recirculation is available in any mode and can be selected with the blower motor in either the ON or OFF position.
Air Inlet Valve Actuator Replacement
Removal Procedure
  1. Remove the Instrument Panel (IP) compartment. Refer to Instrument Panel Compartment Replacement .
remove the glove box
Remove the connector (2). Remove the two screws (1) and the air inlet actuator (3) from the HVAC module.

Apr 18, 2016 | Pontiac Cars & Trucks

1 Answer

Where is drain pipe for a 2008 toyota camry air conditioning system


It's probaly in your blower motor,there's a vent they can come thru,when it's on fresh air.It's located on passenger side below glove box.

Mar 12, 2013 | Cars & Trucks

3 Answers

My fan blower motor only works on high,They say it maybe the resistor may be bad, where is it ? Thanks, Jim


Hi, the resistor is screwed to the side of the blower housing behind the glove box. See procedure below to replace the resistor. You don't have to complete all steps in the procedure. just work your way to the point that you can unscrew the resistor. Please let me know if you have questions, and thanks for using FixYa.

1990-93 Accord

See Figures 2, 3 and 4
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support)

jturcotte_1481.gif

Fig. Fig. 2: Remove the glove box and frame

  1. If not equipped with air conditioning:
    1. Remove the three screws and remove the heater duct.
    2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.

  2. If equipped with air conditioning:
    1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
    2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
    3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
    4. Remove the retaining nuts and remove the blower assembly.
jturcotte_1482.gif

Fig. Fig. 3: Air conditioned models require the removal of the control unit. Handle it carefully


jturcotte_1483.gifjturcotte_418.jpg

Apr 04, 2011 | 1993 Honda Accord

2 Answers

CLICKING NOISE FROM RIGHT DASH ON A 2005 FORD FIVE HUNDRED?


Air/Blend Door Actuator Modual is defective: See info below
Description : Temperature Actuator Attributes : Controls the blend of hot & cold air Make : Ford Brand : Dorman - OE Solutions
Application Notes:
Please select Detailed Applications
for Application Note information. 604-203-007.jpg

Mar 14, 2011 | 2005 Ford Five Hundred

2 Answers

I cant find the blower motor


If you mean the climate control blower motor, it's usually under the dash on the passenger side on Hondas.

1990-93 Accord
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support) Fig. 2: Remove the glove box and frame 86806004.gif

  4. If not equipped with air conditioning:
    1. Remove the three screws and remove the heater duct.
    2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.
  5. If equipped with air conditioning:
    1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
    2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
    3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
    4. Remove the retaining nuts and remove the blower assembly. Fig. 3: Air conditioned models require the removal of the control unit. Handle it carefully 86806005.gif
      Fig. 4: Remove the lower covers from the blower unit 86806006.gif
      To install:
  6. Install the blower unit and tighten the retaining nuts.
  7. On air conditioned vehicles:
    1. Install the lower covers and the retaining band.
    2. Install the control unit bracket and carefully engage the wiring connectors to their proper location.
    3. Install the kick panel and reposition the carpet.
  8. Connect the wiring to the blower assembly. For non-air conditioned vehicles, install the air duct and tighten the screws.
  9. Install the glove box frame and install the glove box. Note that some of trim on the frame is held with 2-sided tape; replace the tape when reassembling as necessary.
  10. If applicable, enable the SRS.
  11. Connect the negative battery cable.
1988-91 Prelude
  1. Disconnect the negative battery cable.
  2. Remove the glove box and frame (lower support).
  3. Remove the 4 screws and remove the heater duct. Fig. 5: The glove box and frame are secured by several small screws 86806007.gif

  4. Remove the 3 mounting bolts.
  5. Unplug the wiring connectors from the blower motor, resistor and recirculation controller. Remove the blower motor assembly.
  6. Reinstall in reverse order. Make certain the blower mating surfaces are tightly sealed.

Jan 08, 2011 | 1992 Honda Accord

1 Answer

The heat in my 2006 grand prix will not get hot. We replaced the thermostat and got nothing. So I got the radiator flush and force filled again. Still nothing. Temp of the motor still gets to the middle,...


Are the 2 tubes that go to the heater core getting hot? If so, then the blend door is not opening to allow heat to get to the cabin.

Possible vacuum motor problem, either disconnected, or the controller for the blend door is broken is likely problem.

Troubleshooting by Symptom Poor Heater System Performance CAUTION
Check all fluid levels and adjust as needed, before operating vehicle for extended periods at idle.
  1. Start the engine.
  2. Idle the engine until the thermostat opens (upper radiator hose will be hot) Is the engine at normal operating temperature (approx. 200° F)? If yes, go to the next step. If no, go to step 16.
  3. Set the mode selector to FLOOR mode.
  4. Set the heater control selector to the warmest temperature setting.
  5. Set the blower speed the lowest setting.
  6. Carefully feel the inlet and outlet heater hoses at the heater core. Is the inlet heater hose significantly hotter than the outlet heater hose? If yes, go to step 14. If no, go to the next step.
  7. Set the mode selector to PANEL mode.
  8. Select the maximum blower speed.
  9. Select the warmest temperature setting.
  10. Place a thermometer into the center I/P PANEL air outlet and affix a second thermometer to the heater core outlet heater hose.
  11. Record the temperature at the center I/P PANEL air outlet and at the heater core outlet heater hose. Are the two temperature readings about equal? If yes, go to the next step. If no, go to step 13.
  12. Inspect and repair the cowl, cowl area, recirculation door, and the HVAC evaporator/heater core case for cold air leaks. Repair any problems found, go to step 17.
  13. Inspect the temperature door operation. Repair any problems found, go to step 17.
  14. Turn OFF the engine. Back-flush the heater core. Start the engine. Select the FLOOR mode and the lowest blower speed. Select the warmest temperature setting. Feel the temperature of the inlet and outlet heater hoses at the heater core. Is the inlet heater hose feel significantly hotter than the outlet heater hose? If yes, go to the next step. If no, go to step 17.
  15. Replace the heater core. When the repair is completed, go to step 17.
  16. Check for low engine temperature problems, Repair or replace as needed, go to step 17.
  17. Operate the system in order to verify the repair. If the system operates properly, the repair is complete. If the heater still does not work properly, repeat the entire procedure.
Air Door Actuators/Motors Removal & Installation Recirculation Actuator To Remove:
  1. Remove the right lower instrument panel (I/P) insulator.
  2. Remove the glove box assembly. Recirculation actuator (Typical) gm-10-00-3695.gif

  3. Remove the mounting screws and recirculation actuator from the HVAC module assembly.
  4. Disconnect the recirculation actuator harness connector.
To Install:
  1. Align the recirculation actuator slots with the flats on the actuator door shaft.
  2. Install and secure the recirculation actuator on the HVAC module assembly with the mounting screws.
  3. Connect the recirculation actuator harness connector.
  4. Install the glove box assembly.
  5. Install the right lower I/P insulator.
  6. Calibrate the recirculation actuator.
Mode Actuator To Remove:
  1. Remove the right lower instrument panel (I/P) insulator.
  2. Remove the glove box assembly. Mode actuator gm-10-00-4356.gif

  3. Remove the mounting screws and mode actuator from the HVAC module assembly.
  4. Disconnect the mode actuator harness connector.
To Install:
  1. Align the mode actuator slots with the flats on the actuator door shaft.
  2. Install and secure the mode actuator on the HVAC module assembly with the mounting screws.
  3. Connect the mode actuator harness connector.
  4. Install the glove box assembly.
  5. Install the right lower I/P insulator.
  6. Calibrate the mode actuator.
Air Temperature Actuator Right Side To Remove:
  1. Remove the right lower instrument panel (I/P) insulator.
  2. Remove the glove box assembly. Air temperature actuator (right side) gm-10-00-4356.gif

  3. Remove the mounting screws and right air temperature actuator from the HVAC module assembly.
  4. Disconnect the right air temperature actuator harness connector.
To Install:
  1. Align the right air temperature actuator slots with the flats on the actuator door shaft.
  2. Install and secure the right air temperature actuator on the HVAC module assembly with the mounting screws.
  3. Connect the right air temperature actuator harness connector.
  4. Install the glove box assembly.
  5. Install the right lower I/P insulator.
  6. Calibrate the mode actuator.
Left Side To Remove:
  1. Remove the left lower instrument panel (I/P) insulator. Air temperature actuator (left side) gm-10-00-4357.gif

  2. Remove the mounting screws and left air temperature actuator from the HVAC module assembly.
  3. Disconnect the left air temperature actuator harness connector.
To Install:
  1. Align the left air temperature actuator slots with the flats on the actuator door shaft.
  2. Install and secure the left air temperature actuator on the HVAC module assembly with the mounting screws.
  3. Connect the left air temperature actuator harness connector.
  4. Install the left lower I/P insulator.
  5. Calibrate the mode actuator.

Oct 18, 2010 | 2006 Pontiac Grand Prix

1 Answer

After turning the car off there is a terrible noise coming from behind the glove box, It is a clicking or ticking noise as if a fan is turning with an obstruction. Only makes the noise after you turn the...


The blend door actuator is hanging up. This actuator (motor) manipulates the door that allows fresh air or recirculation of air while using climate control.

Sep 04, 2010 | 2007 Chevrolet Impala LS Sedan New Cars

Not finding what you are looking for?
1992 Honda Accord Logo

457 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...