Question about 2004 Mitsubishi Endeavor

1 Answer

My air conditioner blows but will not blow cold. I think it may be a belt. Could it be the compressor?

Posted by on

  • Jonathan Dawson May 11, 2010

    Have you checked to see if it is full of freon. Also c/k to see if the compressor is comming on.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Although it could be any of the major parts (compressor, evaporator, etc.), something to evaluate is if the air that blows is hot (like from the heater). If so, the problem is the blender door actuator.

Posted on Nov 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The flap on 2009 traverse air conditioner will not blow cold air when air is on only hot air what could this be


Is their gas in the AC system ?? does it blow cold in a different position? ,think this needs a AC regas to be honest but without a look myself ,is the compressor clicking in when ac turned on and off

Aug 09, 2014 | Cars & Trucks

1 Answer

My air conditioner is blowing warm air on the driver side and cold on the passenger side


see this steps and think with clearly and logically NOT feared. God bless you
checkmark.gif Start with the compressor. Does it engage when you turn on the A/C?
If so, the compressor is working and the A/C system probably contains enough refrigerant to make cold air, so the problem is inside the HVAC unit. Replace the motor that controls the blend air door (this is a difficult job and best left to a professional since it involves tearing apart the HVAC unit -- about an 8 to 10 hour job!).
If the compressor does not engage when you turn on the A/C, see if it will run by jumping the compressor clutch wire directly to the battery (use a fused jumper wire). If the compressor works when you jump it, and the A/C blows cold air, the system contains refrigerant and the fault is likely a bad A/C compressor clutch relay or a bad clutch cycling switch or pressure switch.
If the compressor does not engage when you jump it, the problem is a bad compressor clutch.
If the clutch engages but the compressor does not turn (the belt will start to slip and squeal), the compressor is locked up and you need a new compressor.
If the compressor clutch engages and turns the compressor, but the A/C still does not blow cold air, the system is probably low on refrigerant and needs to be recharged.

7_25_2012_8_45_21_am.jpg

Jul 24, 2012 | 2007 GMC Sierra Classic

1 Answer

Air conditioner light inside truck comes on but blows only regular air.. not cold at all


It isn't blowing AC at all, just air. See if your compressor is turning with the belts when the system is engaged. Not just the pully but the compressor.

Jun 08, 2011 | 2006 Dodge Ram 3500 Truck

1 Answer

Problem with heating and air conditioning. The driver's side is blowing hot air and the passenger side is blowing cold air


Air Conditioner blows warm air
  1. Air conditioner system is discharged. Have the system evacuated, charged and leak tested by an MVAC certified technician, utilizing approved recovery/recycling equipment. Repair as necessary.
  2. Air conditioner compressor clutch not engaging. Check compressor clutch wiring, electrical connections and compressor clutch, and repair or replace as necessary.

Jun 01, 2011 | 2004 Buick Century

1 Answer

Air conditioner not blowing cold air. We put coolant with gauge reading 25 lbs pressure. We think the compressor is coming on. The pipe coming out of the compressor is cool but, the air coming into the car...


Is the air actually blowing into the car?But it's just hot?It sounds like your blower motor is not turning to blow air.you have a fuse,check the switch that controls the blower,and the blower motor it self.

Jul 27, 2009 | Saturn L-Series Cars & Trucks

1 Answer

Air conditioner is not blowing cold air,


What pressure did you have? And Is the front of the compressor turning when you have this pressure. Also feel the two lines going to the compressor, one should be hot and one should be cold.

Jun 28, 2009 | 2000 Chrysler Town & Country

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

267 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...