Question about 2005 Nissan Altima

1 Answer

Engine stalling

Tweetybird what sensor (s) were changed out. Thanks Please reply.

Posted by on

1 Answer

There is a safety recall on 05 Nissan Altimas because of this problem, contact your dealership!

Posted on Oct 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Having trouble keeping truck cranked while driving. changed fuel pump and filter and just recently changed crank sensor which worked for awhile and then same results before it was changed. it seems as the...


If the crank sensor solved the problem before it may have gone bad already , I would start with that. Fuel pressure on a 95 grand needs to be 37 to 41 psi. Check to make sure you have adequate pressure . You may also want to test your Idle air control valve and Throttle position sensor to insure proper operation.

Jan 26, 2015 | 1995 Jeep Grand Cherokee

2 Answers

Engine stall at iddle


Check for any cracked vacuum hose, Throttle clean it Check if you have any place sucking air.

Nov 22, 2013 | BMW 328 Cars & Trucks

2 Answers

I have an 02 jeep liberty stalls after warm and is throwing multiple knock sensor codes p0325, p0330 help


P0325, P0330 are both knock sensor codes that are detected by your ECU. Considering that you are showing both codes indicates that your model trim level is either "Limited" or "Renegade" that will have a knock sensor for 2 banks (V6). Knock sensor errors will change the timing of your engine ignition and can lead to a drop in performance or worse, lead to engine stalling in order to save other components of your engine.
The common solution to remove knock sensor codes is to have the sensors replaced by an authorized mechanic; sometimes shorted electrical leads to the sensors are also a cause for the codes. Replacing the knock sensors will remove the prompting of P0325, P0330 and expect to find another fault as engine stalling is not always present with knock sensor error codes.
Hope this helps.

Nov 05, 2013 | Cars & Trucks

2 Answers

PO103 and 116 code on a 1997 jetta 2.0


P0103 - Mass or volume air flow circuit high input.

Symptoms: Engine stalls, running rough, excessive fuel consumption, excessive smoke from the tail pipe, check engine light on.

Possible Causes: Dirty mass air flow sensor, dirty mass air filter, mass air flow sensor harness is open or shorted, mass air flow sensor electrical circuit poor connection, intake air leaks, faulty mass air flow sensor.

P0116 - Engine coolant temperature circuit range/performance.

Symptoms: Check engine light on.

Possible Causes: Low engine coolant level, ECT sensor harness open or shorted, ECT electrical circuit poor connection, faulty engine coolant temperature sensor (ECT), faulty engine coolant thermostat.

Apr 27, 2011 | Volkswagen Jetta Cars & Trucks

2 Answers

Ford foucs 2000 after engine is warm engine stall


check the engine breather pipes which are situated under inlet manifold at the front of the engine right hand side ,they perish and **** in air causing the problem you describe

Feb 14, 2011 | 2000 Ford Focus

2 Answers

Last night my sebring stalled out of nowhere and then the check engine light along with the oil pressure light appeared. There was no unusual knocking sounds or anything. I keep the oil changed and up to...


Get it scanned for the check engine light, (mil light), as for the oil light, thats normal due to engine not running and making no oil pressure. was this a sudden stall, with no engine surging, then I suppect a failed cam or crank sensor. if it kind of stalled with engine surge and hesatation, I suspect fuel related, possible fuel pump. 2.4L, 2.7L engine have same sensor issues and ideas. if you need more info, just reply back with the mil code, I will walk you through this problem.
GOOD LUCK, RDJRP.

Jul 17, 2010 | 2001 Chrysler Sebring

1 Answer

Engine hesitates or stalls


This might be what we call vapor lock try driving with your gas cap off and see if it still quits under the same conditions.

Jun 17, 2009 | 1999 Pontiac Sunfire

3 Answers

2000 ford explorer 4.0 x-engine is stalling, missing and lose power while driving


I personally would check the fuel pressure. Then I would go back to the coil. I have seen brand new bad coils out of the box. The symptoms of a loss of power point to this component, especially if the car idles well, but loses power when accelerating. Please do not rate this reply - we all are left to grasp at straws since you have changed pretty much everything. Good Luck. Please post the final fix of the problem.

Oct 15, 2008 | 2000 Ford Explorer

1 Answer

Ser.eng.soon flashes code 34 MAP sensor


A code 34 calls attention to the MAF sensor, not a MAP sensor. Try changing that out, first. You might also be having problems with your ignition control module.

Jul 20, 2008 | 1988 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
2005 Nissan Altima Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...