Question about 1997 Jeep Wrangler

1 Answer

Wiring these lights are on 4 different places do i still use 1 wire or do i use multiple peices

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 594 Answers

If you want to use the lights all at one than you can still use only one wire. but if you want to use like 2 for the front and 2 for the back than you will need to connect 2 of them the way i descibed and than hook up the other 2 the same way you will just need to get another toggle switch to run them.

Posted on Aug 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlights not working


1. Verify that both low beam headlights are not burned out.

2. If both headlights are OK, inspect the low beam wiring and connections.

3. Check for corrosion at connector C101

4. C101 is a 15 cavity black connector located under the battery. If OK, backprobe and ground the Dark Blue low beam wire at that point, if the lights work check the Dark Blue wire for an open back to the switch. If they do not work check for an open up to the headlights.

Apr 14, 2013 | 2000 Chevrolet Cavalier

1 Answer

Vehicle idles poorly. Dies after waiting at stop light. Dies when placed in reverse. Vehicle in the last year has gone through 3sets of spark plugs and wires, 3 distributor caps and rotor buttons, 4...


has fuel filter been changed- try this first if not , then i would look at the catalytic converter- if no exhaust out can cause poor idle,misfiring and burnt up ignition parts

Jun 03, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Programing remote starter 98 stratus


here's what u do and make sure u have all u need ie: keyfob and wire handy before u start:

1: Find your obd port(should be under your dash) and insert your key into the ignition but leave it in the off position.
2: The obd port is a wedge shape, the wider end is up with the left top being pin 1 and the number goes up from left to right then jumps down the the bottom row from there, get a peice of wire strip the ends and put it in pin 1 and the other end in pin 4.
3. Within 10 seconds of putting the wire in place press your hazard light button 6 times **you'll get a lock/unlock sequence to let u know you did it right and you are now in programming mode**
4. Now press the lock button on your keyfob 3 times **you'll get a lock/unlock to acknowledge you programmed this remote**
5. You can program up to 5 remotes by repeating step 4 over.
6. To exit programming mode remove the key from your ignition.

Dec 16, 2010 | 1998 Dodge Stratus

1 Answer

ABS LIGHT ON ONLY ON RIGHT TURNS NO SCAN TOOL TO CHECK 4 CODES


Refer to the vehicle user manual for possible diagnostic to lighstening displays. The vehicle would possibly have manufacturer specification different than other vehicles


perform physical checks
1. check for wiring default on electrical kits, circuit fuse boxes, battery installation kits fo alternator wires

2. check for light bulb defects light blownout or burnt outs.

3. check for switch defects that turn on functionality

Important notes
The scanner tool diagnostic device would have provided the solution including the places where current outflow fell short. However, a physical examiantion is possible means for restoration functionaility

Dec 02, 2010 | 2006 Toyota RAV4

1 Answer

I AM CHANGING THE DRIVER DOOR ON MY HONDA ACCORD AND I HAD TO CUT THE WIRES AND I NEED HELP PUTTING IT BACK TOGEHER


You will need a soldering iron and some acid core solder. Skin back about 1/2-3/4 inch of wire on each wire, add a peice of shrink tube, twist the wires together and solder them together, side the shrink tube over the soldered area and heat the tube to shrink, or use some electrical tape. Make sure everything is taped up well to keep water out.

Mar 11, 2010 | Honda Accord Cars & Trucks

1 Answer

Battery dead and key is locked in truck 05 sportrack. keyless entry wont work because battery is dead


OK. Here goes; look at the ground wire on any utility pole. Go to Home Depot, Lowe's or the like and purchase a 4 foot peice of wire like the ground wire (steel not copper). Bend one end 90 degrees at about 6 inches of length. Then bend a slow curve in the entire length of the wire. Purchase 2 rubber door stops. Grasp the top right edge of your car door and gently pull outward. Insert a door stop. Place the other door stop at the top of the door and lightly hit it with the heel of your hand. What you are doing is opening the door JUST ENOUGH to insert the wire without damaging the weather stripping. Now use the wire to either pull the door handle or pull the lock to the open position.

Jan 18, 2010 | 2005 Ford Explorer Sport Trac

1 Answer

Installing distibitor 1997 5.7vortec


with # 1 piston (front piston on drivers side) on tdc compression stroke place distributor in pointing at the front of the drivers front tire as it drops in it should point roughly at the # 1 piston as it rotates clockwise as it drops in , the cam gears have to mesh so dont force it . if it wont drop into place try a small bump of the starter while applying light pressure down on the dist.it should drop into place and then lock it down a bit . get #1 piston back on tdc compression stroke make sure the power wire is off the dist . the big red 1..you dont want it having spark yet. if it goes into place then set your cap and wires back in and time it with timing light .remove vacum hose from vacum can on side of dist and plug the hose off then use timing light and set to what factory says , usually between 4-8 degrees btdc. 1-3-5-7 piston numbers front to back drivers side ///// 2-4-6-8 front to back on pass side firing order is 1-8-4-3-6-5-7-2 and the dist should have #1 pointing at the drivers front corner of engine. start # 1 plug wire there and work clockwise next spot clockwise on dist is #8 plug wire and so on.. good luck

Nov 19, 2009 | 1997 Chevrolet K1500

5 Answers

Misfire


One question, have you replaced the ECTS (Electronic Cooling Temperature Sensor)? These cause no end of different seemingly unrelated problems on Saturns. Peice is about ten bucks and is an easy install. Just search on youtube for a how-to video. Even if that's not the problem it is reccommended to replace this peice just the same as they ALL end up going bad at some point.

If that's not a fix, start pulling plugs. Check to see if they're correctly gapped and if they have any damage/corrosion. If you're running Platinum plugs, immediatly change to a copper plug as Platinums have no place in these motors. Most people have the best luck with NGK copper.

Check to make sure that your plug wires haven't been crossed. This sounds like a plug or wire issue most likely so it has to be in that family, if the plugs are good, wires good and not crossed, sensors are fine, then time to replace your coil packs. If you've replaced everything up to the coil packs then that is most likely the cause of your dillema.


Oct 21, 2008 | 1998 Saturn SL

Not finding what you are looking for?
1997 Jeep Wrangler Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...