Question about 1999 Ford Econoline

1 Answer

Reprogramming keyless entry remote...

Bought and replaced batteries in remote. How do I get the van to recognize the remote. ( The other remote still works). Also, will I have to reprogram both remotes?

Posted by on

  • 1 more comment 
  • Anonymous Oct 25, 2008

    i went to program and it doesnt lock unlock after the 8 turns any ideas?

  • koolchik_70
    koolchik_70 Jan 19, 2013

    I am having the same issue

  • Anonymous Mar 12, 2014

    i bought a 2003 caravan, ordered a remote off ebay ( 502 astro start )but don't know how to program it for my van

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Believe it or not, the information and instructions for reprogramming your particular model of vehicle is provided in your owner's manual. The dealer does not need to be involved unless you have lost all your programmed and programmable keys.

Posted on Aug 30, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bought a used keyless entry remote key fob, how do I reprogram it to a 2008 suzuki sx4?


the operators guide covers this.
lost that? (in the glove box is was)

Jul 02, 2014 | 2008 Suzuki SX4

1 Answer

I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.


Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

Nov 28, 2010 | 1996 Ford Econoline

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

1 Answer

Keyless entry doeasnt work


if its factory keyless entry, chances are your battery for your remote need to be replaced, the remote could also need to be reprogrammed... If it is an after-market system, there are several possibilities... wires could be pinched, the door lock solenoids could be broken or misaligned, the "brain" of the system might need to be reprogrammed.

Apr 24, 2010 | 2001 Chevrolet Blazer

1 Answer

My powerlocks on my mercedes 2000 s500 wont repond to my keyless entry


REMOTE KEYLESS ENTRY BATTERY IS WEAK OR DEAD.YOU HAVE TO LET DEALERSHIP REPLACE KEYLESS ENTRY AND REPROGRAM IT TO UNLOCK OR LOCK DOORS.

Oct 17, 2009 | 2000 Mercedes-Benz S-Class

1 Answer

How to program a keyless entry for land rover


MOST OF THE TIME WHEN YOU HAVE PROBLEMS IN THE REMOTE AND KEYLESS ENTRY.THE DEALERSHIP HAS TO REPROGRAM IT.BUT FIRST CHECK ALL THE FUSES AND RELAYS.IF THEY ARE OKAY.THEN DEALERSHIP HAS TO FIX.

Sep 16, 2009 | 2004 Land Rover Discovery

1 Answer

Keyless entry not working


Mine did the same thing, but it was the battery claw on the inside of the remote has come loose from the circuit board. I bought one from www.keylessride.com its like 45bucks after shipping. Its better then the 120 the dealer wanted. They will send you reprogramming steps too, it was super easy.

Apr 16, 2009 | 2004 Chevrolet S-10

2 Answers

Reprogram a keyless entry remote


Hello
this is how to program the remotes/keyless entry

How
  • Obtain all remote transmitters
  • enter the 5 digit permanent code into the keyless entry pad on the drivers door
  • Press the 1-2 switch on the keyless entry pad
  • Within 5 seconds
  • Press any button on the first remote transmitter
  • The doors should open then lock
  • Within 5 seconds
  • press any button on the second & third remote
  • within 5 seconds for each remote
  • to exit programming
  • simultanionusly press 7-8 & 9-0 switchs on the key pad or wait more then 7.5 seconds
NOTE
The 5 digit permanent code is located in one of the following places
  1. On the owners warranty card
  2. On the label on the inside the trunk/ boot
  3. On the owners code card
  4. On the centrel locking control module located in the drivers door
  5. In the PCM ford can get this for about $25.00
I hope this help
Regards Paul
www.limotec.co.uk

Jan 13, 2009 | 1995 Lincoln Town Car

1 Answer

Keyless entry not working


the keyless entry system is tied into the computer system and needs to reprogramed by the dealership

Nov 30, 2008 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Ford Econoline Logo

918 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...