Question about 2000 Suzuki Swift

1 Answer

Check engine light

Hi, I have a 1999 suzuki carry van and i had to replace the oring on the sensor on the cam however when i tried to remove the electrical connector that goes into the sensor it broke and i didn't take notice how the wires went itno the sensor the van starts but the check engine sensor light is now on could it be that the wires are not connected correctly or would it have blown the sensor and not started if they were incorrectly connected any help would be appreciated cheers dave

Posted by on

  • chriswoll Mar 08, 2009

    Hi my mother has a 1999 suzuki carry that has a engine warning light that comes on and the car overheats and starts to rattle and stops. She has had the coils exchanged as well as the muffler and has had the car at three different mechanics and it still does the same thing....please help
    ; (



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers


Posted on Feb 25, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the cam shaft sensor located on a 1999 Suzuki Esteem 1.8 Suzuki

double posted. by OP
the 1.8L , is on the left rear of cam, it a twin cam engine, DOHC.
face the engines, front pulley, point to right rear of cam shaft. bingo. CMP

on the 1999, In usa, any scan tool will till you its bad. for sure.
P03xx codes. 340 are cmp failure.
can be seen driving, or parked, engine running, or even CRANKING.
if the scan tool shows no, errors with it, it's not bad.
the PCM will show even 1 missing pulse in 10. (drop outs)
fact. (covered in the FSM book)

here is the parts page.
page 21 shows the mount.


Jun 01, 2015 | 1999 Suzuki Esteem

1 Answer

How do I set the timing on a Suzuki F8A 997cc 4 cyl/4 stroke engine

what country?
cam timing?
it's and engine swap. what year engine, ?

SOHC F8A, which appeared in 1977.

what car did it come out of and what year/?

Feb 19, 2015 | 1985 Suzuki Swift

1 Answer

What is the firing order for a 4 cylinder Suzuki Carry Van 1994?

1-3-4-2 with the number one at timing belt end.

Aug 15, 2014 | 1999 Suzuki Wagon

1 Answer

Fast idle

Sounds like your throttle position sensor is bad.
Take it to Auto Zone and ask them to pull any computer codees that may be latched. Not sll codes trigger the check engine light

Apr 04, 2010 | 1999 Buick Century

2 Answers

Suzuki Vitara V6, MAF sensor, white smoke.

My first thoughts are that you have a head gasket or intake manifold gasket failure. This is why you have the white smoke. If you run it too long, your catalytic converter will be destroyed. Check for coolant in your oil too.

Dec 01, 2009 | 1999 Suzuki Vitara

1 Answer

2001 chevy venture engine hesitating

there could be several reasons for this type of problem. the engine is controled through main computer(ECM) and the sensors assocciated with it. most often times a hesitation is commonly a idle issue and that would be monitored by the TPS ( throttle position sensor) if this is beginning to fail it sends faulty reradings to the computer and the computer tries to compensate and sometimes either leans or richens the fuel air mixture cause and effect is a engine stall or a hesitation. another factor is your (O2) sensors these monitor your exaust and tell the ECM to adjust accordingly the fuel mixture also. a sure fire way to tell if one ore more sensors are faulty is to either have your check engine light come on or if there is a rough start. if the check engine light isn't on then i would think there is a timing issue involved and a tune up is in order. the tune up is simple by just changing plugs and wires, however the timing is computer controled and can only be adjusted by a certified tech with the proper equipment. try and change the plugs and wires first this is the least expensive way to solve your problem. if the problem persists then take it to a shop and have a tech hook up diagnostic tools to check the ecm for fault codes to narrow down whatsensors if any are faulty.

Apr 17, 2009 | 1999 Chevrolet Venture

3 Answers

I have Suzuki baleno 1,3 specail, 2000. I need the electric fuses layout

i have a 2000 model suziki baleno when then car warms up the check engine light comes on and tries to stall and has no power the car has done 82000 klm

Apr 14, 2009 | Suzuki Aerio Cars & Trucks

1 Answer

Check engine light came on garage says lambda sensor so fitted new one. now exhaust smelling - extremely stinking hot under passenger seat near battery. Engine tries to cut out when ticking over - gets...

Check whether your Catalytic converter is clogged. does the emission smell like rotten eggs? also when accelerating check the output on the end of your exhaust is strong or poor.If so the cat is the fault thats why you had Lambda sensor faulty.

Dec 26, 2017 | Suzuki Cars & Trucks

Not finding what you are looking for?
2000 Suzuki Swift Logo

Related Topics:

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides