Question about 1995 Jeep Cherokee

1 Answer

Where is the crank shaft sensor located

I have a jeep grank cherokee 2003, diagnosed the problem, picked up the part and ready to replace. where is it?
Mona

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 30 Answers

On a 4.7L It is located just above your starter. I believe you have to remove the starter to get to the bolt for the sensor. Also use a twist motion when removing the old sensor.

Posted on Aug 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE TO CHANGE OUT A CRANK SENSOR IN MY GRAND CHEROKEE.


Jeep Crank Sensor Replacement, P Codes P0351, P1391 ...

? 6:24
www.youtube.com/watch?v=7D0vUEDSwXo
May 12, 2013 - Uploaded by Robert DIY Replaced the crank sensor on this 2003 Jeep Grand Cherokee.... to replace my crankshaft position sensor on my 1998 grand cherokee laredo.

Jeep Crankshaft Position Sensor Replacement (CKP, CKPS ...

? 4:07
www.youtube.com/watch?v=1Ho5iAKQV00

Oct 27, 2013 - Uploaded by WeekendHandymen
hi , do you think if I replace crank sensor will solve the problem ,my jeep .... Where's the crankshaft located in 99 jeep grand Cherokee laredo .


Oct 24, 2015 | Cars & Trucks

1 Answer

2002 jeep grand cherokee diagnostic trouble code P 0320? how do i repair?


No Crank Reference Signal at PCM No reference signal (crank-shaft position sensor) detected during engine cranking. Use this youtube step-by-step to fix it. How to diagnose P0320 crankshaft position sensor circuit failure

May 01, 2014 | 2002 Jeep Grand Cherokee

1 Answer

Where is crank shaft position sensor located on 1997 jeep grand cherokee


CRANKSHAFT POSITION SENSOR LOCATION FOR 4.0L ENGINE IS ON TRANSMISSION BELLHOUSING AT THE LEFT REAR OF THE ENGINE. FOR 5.2L ENGINE CRANKSHAFT SENSOR LOCATED ENGINE BLOCK BEHIND THE RIGHT CYLINDER HEAD.

Dec 11, 2010 | 1997 Jeep Grand Cherokee

1 Answer

Locate crank shaft sensor on 1998 jeep grand cherokee


4.7L ENGINE CRANKSHAFT SENSOR LOCATED ON THE ENGINE BLOCK ABOVE THE STARTER. ON THE 4.0L ENGINE CRANKSHAFT SENSOR LOCATED TRANSMISSION BELL HOUSING AT THE LEFT REAR OF THE ENGINE. THE 5.2L 5.9L CRANKSHAFT SENSOR LOCATED ON THE ENGINE BLOCK BEHIND THE RIGHT CYLINDER HEAD.

Nov 26, 2010 | 1998 Jeep Grand Cherokee

1 Answer

I own a 2002 Jeep Cherokee. Where is the oxygen sensor bank 2 sensor 2 located. This jeep has 4 oxygen sensors. Thanks


the bank 1 and 2 refer to what side of the car ir is on. Bank 1 is passenger side bank 2 is drivers side sensor 1 and 2 refer to before and after the catalytic. sensor 1 is before and 2 is after . i hope this helps and just a references if your cam shaft sensor and crank shaft sensor have not gone bad yet i would have them checked. usually these go bad really quick on jeeps. just had to replace both my cam and crank sensors and with out labor it cost around 100 with labor about 150 to 200. and the o2 sensors run anywhere from about 50 to 150 depends on the quality you want

Nov 03, 2010 | 2002 Jeep Grand Cherokee

2 Answers

2001 jeep cherokee cranks but wont start and has


If all the fuses are good,replace the crank shaft sensor,this is the problem.

Jan 04, 2010 | 2001 Jeep Cherokee

2 Answers

93' Grand Cherokee, dont start, no spark,no gas preassure


my 1996 jeep grand cherokee lmtd. won't start did tune up. cranks but no fire. please help. engine code 54 shows up . cam shaft positioning no signal. . tested all circuit. changed cam shaft positioning sensor twice.still cranks did start once ran for 5 min. changed the sensor again. no luck. help please. keith

Sep 10, 2009 | 1993 Jeep Grand Cherokee

1 Answer

Need to replace crank sensor on 2003 jeep grand cherokee


its easy, its underneath the passenger side located halfway up the transmission bell housing unplug, u will need to use a 1/4inch drive ratchet and socket to loosen the bolt and simply remove and reinstall with the new one

Jul 04, 2009 | 2003 Chrysler PT Cruiser

1 Answer

2003 Grand Cherokee Laredo turns off when put on reverse.


Throttle Possition Sensor is the usual issue for your concern

Jun 30, 2009 | 2003 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Cherokee Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...