Question about 1999 Suzuki Vitara

1 Answer

Front axle how to remove half shaft

Need to remove half shaft front right cant pull out the axle from diff
help help vitara 2000

thanks mate
charles

Posted by on

  • charlescilla Aug 19, 2008

    guill you are very good , thanks for input but I only need to renew c/v rubbers think I gave wrong info do I have to follow your instructions or is it a bit simpler thought would remove wheel etc till came to axle front right pull out and slip on new rubber but could not get axle from diff front thought might be a circlip or other

    Thanks again mate

  • Anonymous Mar 22, 2014

    rear axle shaft removal

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 373 Answers

Hi.. The step to remove the front Axles of you Vitara.
Raise and support Vehicle . Remove front wheel,
Drain Diff,fluid,
Remove Locking Hub if is equipaded,
Remove Circle clip from axle shaft
On right side of Vehicle, Remove the Stabilizer Little ball joint nut. Remove castle nut Front Tie rod end,
Remove mounting bolts from brake calipper,
Remove Calipper from steering knuckle and wire a side.
Remove Stud Nut from steering knuckle,
Support Lower suspension arm with a jack,
Remove lower strut bracket bolt ,
Lower jack and disconnect Knuckle from lower suspension crontrol arm,
Pull Outler joint from Hub.
Use Large screwdriver or Prybar To pry Right inner joint from differential, The axle will go out making a little froce with the prybar,
To remove the left side,
Remove mounting bolt from inner joint flange,
Pull out axle from hub.

To reinstall just reverse the prosses.

I hope this help on your job...
Thank you for use fixya....


Posted on Aug 19, 2008

  • Juan Guillen Aug 19, 2008

    Ok..

    Is there a CIRCLE CLIP.

    Inside of the cv axle joint head.

    You need to remove the cv boot clamp from the bigger side to the small side.

    if you clean the grease you will see inner circle clip. at the size of the cup.

    With a fine screw driver remove the clip.

    After you remove the clip. you will able to separate the axle and joint head,

    To remove and install the cv BOOT.



    I hope this work """"""""""""""""""Thank's""""""""""



×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Halfshaft will not come out of passerger side differential


Try Autozone's loan-a-tool deal. The typical half-shaft remover is a fork that fits between the inner CV's housing and the transaxle case. The fork is attached to a slide hammer, only takes a blow or two to pull the half-shaft free.
Another way is to get a large screwdriver or pry bar or punch, use it against the inner CV's housing, tap it outward with a hammer. If you can get a good whack on it, it usually frees the axle. There is a circlip (ring) in a groove on the inner end of the shaft. This circlip fits in a corresponding groove in the transaxle gears. Once the ring clears the groove, the axle will slip right out.

Oct 04, 2015 | 2000 Suzuki Vitara

2 Answers

How do you pull a 1979 gmc jimmy 4x4 rear right axle


QU40221 19 Spline Outer Axle Shaft for 1977 to 1991 Chevy, GMC Corporate GM 10 Bolt Front Axle is a genuine original equipment outer axle stub shaft for all GM 10 Bolt front axles in 1977 to 1991 Chevy Blazers, GMC Jimmys, and Suburbans, plus Chevy, GMC 4x4 1/2 ton and 3/4 ton Pickups. The splined end on these new axle shafts has three snap ring grooves in three places so they are compatible with all types of automatic and manual lockout hubs plus all full-time solid splined drive gears.

Also available while supplies last: QU40221U Used Outer Axle Shaft with 3 snap ring grooves and QU40660UUsed Inner Axle Shafts with 2 snap ring grooves (QU40660U is not compatible with automatic locking hubs)



see this vdio

Apr 01, 2015 | GMC Jimmy Cars & Trucks

1 Answer

How do I replace my inner axle on the passenger side of my 2002 Dodge Ram 4x4 4.7L. I lent my truck out and the C clip let go of the CV axle. The intermediate axle spline is stripped and I need to change...


Lift and support front end on suitable jack stands preferably on frame. Remove right front cv axle, stub shaft, and seal. You will need to pull the right front brake caliper assembly loose and place to the side. Then remove bolts from shock and upper control arm and hub nut to do this. Next, remove axle lock actuator on passenger side of front axle. Place a drain pan underneath front diff cover and remove cover and drain axle. In the center of differential there will be an 8 mm head bolt holding spider gear cross-shaft. Remove bolt and cross-shaft only! Push inner axle in until clip clears inside of passenger spider gear. Set clip aside and push/pull axle shaft straight out to passenger side.

Feb 09, 2015 | Dodge Cars & Trucks

1 Answer

Can't remove rear axel yoke


im not sure of your question. ?
that is a drive shaft and or propeller shaft, off
fist start by saying, what you are doing? we dont know.
What is the goal, ????
my guess is, removing the axle carrier from the axle housing?
you must remove both axles to do that.
here is a 2004 , axles being pulled. (im guessing what you are doing)
http://www.fixkick.com/axles/axle_rear_R&R.html

Apr 19, 2013 | 2000 Suzuki Grand Vitara

1 Answer

Rear differential how to pull axles


you have to remove the four bolts in the brake back plate ,then remove the rear cover on the diff ,then strip the planet gears ,then on the end of the half shaft is a horse shoe shape clip ,pull this out then the half shaft comes out

Nov 10, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Front diff. wont lock into 4x4. Transfer case is working. Vacume Dia. under battery tray is working. Could the shifting fork in the diff be broke


The cable from the differential to the accumulator should move somewhat freely. If it does not, then the cable may be froze up. You can lubricate it with some penetrating oil and work it to free it back up. You may have to remove it to free it up properly.You may find the cable shield towards the bottom end is broke off and the cable may completely be froze up, it's common on the Blazers. You can try pulling on the rod that the cable clips into in the front diff to disengage the front axle. If you cannot get it to engage that way, then you will likely have to pull off the passenger side extension housing to access the engagement collar and fork. If you cannot get it to engage by pulling on the fork in the axle, then you will likely have to disassemble it.

You will likely have to file down the leading edge of the gears. They should be beveled on the sides of the spline to aid in engagement. Hopefully yours is not chipped like the one in the front of my old S10. Mine chipped the splines on the axle and split the collar from being partially engaged under power

The right axle and has splines at the end of it. The Output Shaft slides into the carrier and has large teeth on the other end. The collar it has large teeth inside it that mate with the Output Shaft with the Fork.

The collar rests on the axle, the fork wraps around the collar. Then you push the 4x4 button or shift your transfer case into 4x4 it starts spinning the front drive shaft, which spins the carrier and the short shaft. Now your in 4x4, BUT the front axle needs to lock the right axle with the carrier. A switch on the transfer case routes engine vacuum to a diaphragm under the battery tray, that diaphragm pulls a cable which pulls the collar and forces it over the short shaft. Now your front diff is locked. When you take it out of 4x4 the vacuum switch closes and a spring pushes the fork and collar off the shaft unlocking the front diff.

The problem with mine I think is that the large teeth on the Output Shaft and the inside of the collar are worn at the tips, not allowing them to join together, and the more I drove it around with it clicking, thinking it would lock eventually it just wore the tip of the teeth more.

If that is the problem, You should not have to mess with the differential case. You should be able to get the passenger axle extension tube off, but it may require popping a ball joint, then disconnecting the CV shaft from the axle extension tube, which would allow you to then pull the extension tube.

Good luck and hope it's just the shift cable retaining clip in the housing that broke.

Dec 30, 2009 | 1997 Chevrolet Blazer

1 Answer

Need picture on how to break down 1998 blazer **** slip / ratched rear


jack rear end pull wheels & tires brake drums or rotors put truck in neutral pull cover turn drv shaft till you see a 5/16 bolt head or 8mm on right hand side pull bolt out a pin should fall out if not get a hammer & hitt diff in axle once or twice (not the gear the case that gear is attached) remove fallen out pin, push axle shafts in remove a horse shoe retainer from both sides, now pull both axle shafts out, remove the four bolts with caps (warning don't mix caps up) get big pry bar pop diff case out..go to auto zone web sight the have basic help manuals

Sep 09, 2009 | 1998 Chevrolet Blazer

1 Answer

How do I remove the rear axles on my 2000 GMC Yukon XL so I can replace the tin brake liners in the wheel hubs?


well you need to pull rear cover and pull rotors or drums off and there are two clips in side the diff but you need to pull the center shaft out AND PUSH THE SHAFT IN WORD AND REMOVE TWO CLIPS AXLE WILL SLIDE OUT

Aug 13, 2009 | 2000 GMC Yukon XL

3 Answers

My front differential is leaking!


I cannot see it, but I am guessing that you need to replace your axle seal. To do this,you have to pull your CV shaft out. Remove the tire, remove the caliper from the top of the rotor. Using a hammer on the back, remove the rotor. Take off the spindle (axle) nut, separate the axle (CV shaft) from the hub. Replace seal. It should pop right out. Good luck!

Aug 05, 2009 | GMC Sierra 1500 Cars & Trucks

Not finding what you are looking for?
1999 Suzuki Vitara Logo

4,079 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...