Question about 2004 Dodge Ram 1500

Open Question

Location of aballast resistor on a 1988 dodge d-100 v-6

Find location of part ballast resistor dodge 1988 v-6 d-100

Posted by on

  • Ricardo Loranca
    Ricardo Loranca May 11, 2010

    check out the firewall

×

5 Suggested Answers

66 chrgr
  • 1011 Answers

SOURCE: 87 Dodge ignition module location

it is a pick up module in the distributer then to the coil!

Posted on Jan 24, 2009

  • 2 Answers

SOURCE: I need to know where

does not have one for ignition system

Posted on Apr 30, 2009

  • 6982 Answers

SOURCE: ballast resistor location

should be on the firewall...can't remember which side but I think its on driver side It's ceramic rectangle with four wires. (I had one and just can't picture where exactly it was.) One tip though, when you put it back on, use some high temp silicone around top and side edges, leave bottom open. They usually fail from water dripping down and cracking resistor (gets hot).

Posted on May 09, 2009

  • 490 Answers

SOURCE: does a 1987 dodge ram 100 have a ballast resistor?

yes it is in one of two places.The first is look under the hood find the blower motor on the left side standing infront of the van.look under the blower motor to the right and down it should be there.if not look near the center/rear engin compartment,to see if it is there.It is a white ceramic part about 2/3 inches long with twqo wires on it.

Posted on Jul 23, 2009

  • 1 Answer

SOURCE: Ballast Resistor re-wiring '87 dodge Ram 50

I have just wired the ballast to the coil on my 84 D-50 all but two wires...is yours fixed yet or still need help?

Posted on Sep 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 dodge dakota heater resistor location


Should be on the firewall just above the heater box.

Feb 21, 2015 | 1988 Dodge Dakota

1 Answer

Where is the ballast resistor located on a 1996 dodge dakota


cant see a listing for a 1996 dakota ballast resistor
if it had one would be a ceramic block close to the old school round coil

this is its coil
there is an ignition coil driver in the wiring diagram
automotive wiring diagram Ignition Coil Driver 1995 Dodge Dakota Wiring... 17671761-1xghuso0dtf1wvqnhgyxjoi3-1-0.jpg

17671761-1xghuso0dtf1wvqnhgyxjoi3-1-1.jpg

Apr 13, 2013 | Dodge Dakota Cars & Trucks

1 Answer

Where is the ballast resistor located in a 1994 dodge ram 250 van?


You must be living in the 1960's

Ballast resistors were for ignition with points,
to reduce the coil voltage to under 10 Volts

Mar 21, 2013 | Cars & Trucks

2 Answers

Keep burning up coils on a 1990 Dodge Ram Van 2500 with a 318 motor.


there should be a white ballast resistor in the circuit to cut the amperage back on the coil.
Check or replace ballast resistor sometimes they was mounted on firewall next to the ignition module either a 2 prong or 4 prong white ballast resistor.

May 18, 2011 | Dodge Ram 2500 Cars & Trucks

1 Answer

I am trying to get spark to fire the motor in my dodge raider. The ballast resistor and coil had all the wires disconnected. Where do the wires connect back too?


The negative side of the coil goes to ground. The positive side goes to the ballast resistor. The other side of the ballast resistor connects to the ignition switch. More information might be had on manualsonline.com.

Mar 14, 2011 | Dodge Raider Cars & Trucks

1 Answer

I have a 1985 Dodge Ram Charger. I am trying to replace the ballaster resistor and can not locate it. The book show it on the firewall or fender wheel however it is not located any of those places....


Should be on the firewall,yes. Perhaps follow the wire from the coil back to the ballast.
I assume the truck fires then dies as soon as you let off the starter? That's how a bad ballast would act.

Jan 17, 2011 | Dodge Ramcharger Cars & Trucks

1 Answer

Where is the blower motor resistor located on a 1988 dodge lancer


REMOVE GLOVE BOX ASSEMBLY LOWER RIGHT SIDE INSTRUMENT PANEL TRIM COVER AND RIGHT COWL TRIM PANEL. WHEN YOU WILL SEE BLOWER WIRES THATS WHERE YOUR RESISTOR LOCATED. DISCONNECT BLOWER MOTOR WIRES THEN REMOVE RESISTOR.

Dec 06, 2010 | 1988 Dodge Lancer

1 Answer

87 Dodge ignition module location


it is a pick up module in the distributer then to the coil!

Jan 24, 2009 | 1987 Dodge Ram 50

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...