Question about 1997 Eagle Vision

Open Question

97 Eagle Vision ignition problem

I noticed a couple other people here has posted about the same problem. In the off position the A\c blows and the gauges are lit. Once the car ignition is in run position no gauges no A\C running. Would just replacing the ignition fix this, and is there any precautions I need to know about before attempting the repair.
Thanks,
TJ

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 512 Answers

SOURCE: my eagle vision radio is not worrking i need the owners manual

check fuse 2 and 13 in the fuse block inside the car

Posted on Dec 04, 2008

Ad
  • 3 Answers

SOURCE: locate fan sensor on 1997 eagle vision

Your fans (low and high) have number of parts.
1. Temputure sensor
2. Hi and Lo fan relays (PCM)
3. Relay located in the fan assembly itself

If you car over heats either in idle or when you turn the air conditioner you are having an eletrical issue. The fix is easy but can take some time, rewireing and a relay.

Hope this helps

Posted on May 18, 2009

  • 116 Answers

SOURCE: 1996 Vision Eagle runs rough and stalls when started

timing belt

Posted on May 19, 2009

  • 88 Answers

SOURCE: 1996 eagle vision tsi fuel,speedometer,temperature gauges

do you have an amp for the stereo could also be a bad ground most common from big ground on batt should also be a small ground to body let me know

Posted on May 22, 2009

emissionwiz
  • 77169 Answers

SOURCE: 1996 Eagle Vision 3.5 idles too fast. How to fix

yes propane or carb spray will work, just spray around the entire intake area and all vacuum hoses, if u hit a vacuum leak the engine idle will change.

Posted on Nov 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why would the RPMs go over 3000 at idle on a 1995 Eagle Vision if it idles for too long it'll get too hot


Possible vacuum leak, Throttle positioning sensor, idle speed solenoid, Other possibilities too. Don't let it do that for too long, severe engine damage can occur.

Mar 31, 2017 | 1995 Eagle Vision

3 Answers

My eagle vision wont start turn switch i have nothing battery is good starter is good


Hello , i believe your vehicle alternator is charging less than usual 11,5 volt instead of 13.5 v ,, check your vehicle alternator readiing

Nov 04, 2017 | 1993 Eagle Vision

1 Answer

94 Eagle Vision ESI 3.3 litre could run engine,cut off the ignition switch and the dash lights would come on by themselves seconds later. Replaced the key cylinder and ignition switch to no avail; now I...


You mentioned you replaced the key cylinder, did you also replace the switch located in the column, this is the portion that contains the wiring.

Nov 09, 2013 | Eagle Cars & Trucks

1 Answer

Need to replace front body mounts on my 97 Eagle Vision, what is involved? can a DIYer do it?


if you have use of a hoist, a few jack stands , and sir power tools a diy can do it , just loosen the cradle at all corners but don't take them all off, then replace mounts one at a time

Sep 12, 2010 | 1994 Eagle Vision

1 Answer

97 eagle vision o2 sensor ckt no activity bank 1 sensor 1


bout time for a new sensor-hav it tested first--02s are usually expensive

Aug 06, 2010 | 1997 Eagle Vision

1 Answer

I want to drain the water from my 97 Eagle Vision Rad so I can fill the resovior with the corect fluid, where is the point of drainage located? Help Please.


Should be a drain valve located on the bottom of the radiator, if not, you may have to just remove the lower radiator hose. Most radiators have drain valves, but there are a few that don't. Hope this helps

Jul 15, 2009 | 1997 Eagle Vision

Not finding what you are looking for?
1997 Eagle Vision Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Eagle Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Stewart Dibbs

Level 2 Expert

336 Answers

Are you an Eagle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...