My name is Wayne and I'm trying to repair my turn signals. They just stopped working. I have no dash panel lights or blinker sound, and both front and back, left and right lights will not blink. This has also stopped my flasher from working. I have checked my blinker flasher fuse and also my flasher fuse, both show ok.
Hello I had the same problem on my 04 monte. After changing bulbs ,checking wires etc. I finally took it to the dealer and they found out it was the hazard switch. After swapping it with a new one all lights, dash etc started working again and have not had another problem
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
I assume you've checked the Fuses :p Obviously that hasnt worked and the bulbs and lights haven't worked either... SO try this???? Open the driver's side door and
examine the end of the dash for an access panel. Behind the access panel
are fuses and flashers. There are two flashers inside the access panel
for controlling the turn signal and the hazard lights. You can
distinguish them apart from each other by turning on the hazards or the
turn signal and feeling for the clicking. If you turned on the hazards,
then the flasher that is clicking is the hazard flasher. Remove the turn signal flasher
from the dash and reinstall the new flasher into the vacated slot in the
dash. Close the access panel and start thetruck . Check the turn signals for proper operation and make sure the hazards work as well.
If the fuse is good and the flashers work then you have a bad signal flasher, this car uses two flashers in one located under the dash, one controls the hazard lights and the other the signals, these are all inside one flasher, so turn on the hazards to locate it by listening to clicking noise. i have inclosed a diagram to help locate it. its on leftside kick panel by your left foot, replace the flasher and see if that does it, good day
did both signal lights stop working at the same time or not,it may just be the signal flasher has gone bad,it is located under the dash by the fuse panel.if the hazard flashers work then i would say the signal flasher is bad.with the hazards on you can locate it and that is what the signal flasher looks like and it is a separate flasher,
you need to check to see which bulbs don`t work both front and back lights for the signal on the side it`s not working,you don`t say if any signals work or not if no signals work then you need to check the fuses under the dash on the driver`s side.now if it`s just one side then check the lights as mentioned above.if one isn`t then replace the bulb.if neither bulb is working then it sounds like the signal flasher is not working.turn on the hazard flashers and check the lights front and back.if all bulbs work then leave the hazards on and look under the dash for the flasher that is making the noise,this will show what the signal flasher will look like,then find the signal flasher on the fuse panel under the dash it should be located on the fuse panel.and replace
you have a separate flasher for the turn signals.this is what your problem sounds like.if all your lights are working including the signal indicator on the dash then it will be the signal flasher.if you turn on the hazard flashers and locate it under the dash, this will show you what the turn signal flasher will look like.then you will have to look for the flasher unit on the fuse panel that looks like the hazard flasher.replace the turn signal flasher and you will have your signal flashers again
There are 2 Flasher Relays. One for the turn signals and one for the hazard lights. Both flasher relays are located on the driver's side, under the dash, mounted in the fuse panel. Make sure you replace the correct one.
The flasher is a small round plastic cylinder (unless replaced with a metal one) behind the left edge of the glove box that will look similar to the one in the fuse panel. The first step is to squeeze gently both sides of the open glove box and let it swing downward. It will be snapped into a metal horizontal brace just to the left of the glovebox opening by a small tab and have two wires attached. The number more than likely will be a #552 although I have seen a factory one with a Warner #224
the flasher unit controls both hazards and indication you will need to remove the shroud around the steering wheel and follow the wires coming off the indicator stalk down until you find the problem there should be some majour plugs on the stearing collum check thaat these are conected and work from there