Question about 1992 Jeep Wrangler

2 Answers

No brake pedal

I have a 92 jeep wrangler.have replaced everything from brake booster to the pads,shoes have replaced all the lines on this also.have bled the brake system of all the air.still i have no pedal at all.can pump up the pedal and have very limited brake.what could be my problem???

Posted by on

  • DDoggSmilez Mar 03, 2009

    I have the same problem with a 94 Wrangler no pedal on first push but I can pump it to get a bout half pedal replaced my whole braking system and nothing no air in lines. need some help

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi bought 92 wrangler that had the same problem new calipers were on wrong sides bleeders were at bottom instead at top so not all air could escape

Posted on Jul 29, 2010

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

The only thing i can think of is you brake master cylender

Posted on Dec 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why wound brakes work?


Lots of parts replaced for no reason,it seems

All you have to do is learn how to bleed brakes

That is the only problem

Oct 02, 2014 | Cars & Trucks

2 Answers

Brakes are hard to depress causing stopping problem


1: inspect all brake linings first.
no pulling left or right braking?
the car has 100% full manual brakes. if the brake booster fails.
(its only and assist !!! for 50lb small folks)
so does it? it takes more pedal pressure but has 100% full braking.
this is no accident its by design.
make sure none of the brake shoes/pads are soaked in DoT3/4 fluid
or grease or gear oil.
and no brake fluid leaks end to end, this is really #1 on all cars.
look, then look again. even behind and in front of the master cylinder.
look at tires (inside for fluid leaks>)
2: do the booster test. did the vacuum hose to it fall off?
or got pinched, or ?

google brake booster test
if ABS system. get it all checked,
if ABS get the ABS scanned.

if you cant stop correctly,,,,???? , dont drive.
get it fixed.

May 06, 2014 | 1999 Jeep Wrangler

4 Answers

Brake pedal goes nearly to floor front pads, calipers, brake hoses changed, rotors turned Master cylinder changed, brake booster check valve changed rear brakes checked, drums good no ridge, shoe's...


I would go with not bled correctly

The booster should hold up with a hard pedal until
you start the engine, then vacuum causes it to move
down when pressing on the brake

Sep 16, 2011 | Saturn SC Cars & Trucks

2 Answers

Have no brake pressure, pedal goes straight to floor, put on new calipers and pads and bled the lines but I am no better off.


Sounds like a bad brake booster. To test, pump up the brakes with the engine off. While holding the brake pedal down,start the car. The brake pedal should drop a couple of inches and hold. If it doesn't, replace the booster.

Jul 25, 2011 | 1996 Jeep Grand Cherokee

2 Answers

Spongy brake pedal apears to be leaking fluid from brake booster


check or adjust brake pedal, check brake booster or replace new one, check pedal return spring and bushing, check all wheel cylinder or replace, check brake shoe or brake pad, check brake fluid or replace,.

Apr 03, 2011 | 1999 Pontiac Sunfire

1 Answer

Brake petal goes to floor


if you cant find any leaks in lines or cylinders or calipers u probaly have a bad booster
see lots come threw my shop like that but also their is a vacum line that runs to the booster and it hooks to a plastic valve that goes in to the booster those get gloged and you loose pedal as well try replacing that before you bye a new boooster

Mar 26, 2009 | 2000 Jeep Grand Cherokee

2 Answers

97 ford e350 brake pedal goes to the floor...


are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

1 Answer

Brakes aren't working. put in 3 cans of brake fluid, can't find leak but fluid disappears. what next?


Try pumping pedal with booster vacuum line disconnected at booster,
check if any fluid at vacuum connection.
Do this with engine not running.
Please let me know if pedal goes hard and fluid at vacuum port
, if so booster is faulty

Aug 01, 2008 | 1995 Jeep Wrangler

2 Answers

Hard pedal low stopping power


First you need to check the brakes lines and the brake pads must be replaced on your car they may be worn out........ Get it checked from the local service center........

May 30, 2008 | 1991 Buick Regal

Not finding what you are looking for?
1992 Jeep Wrangler Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...