Question about 1988 Mazda B2600 Cab Plus

1 Answer

Hi, I have a 91 Mazda B2600 5 speed fuel injected truck. Recently it started dying and I thought it was the fuel pump. I replaced the fuel pump, and it ran great for around 10 minutes and then died again. It will then try to turn over but won't. If you let it sit for around 30 min it will fire up again but only run for a little while then die again. I checked to see if it is getting fire and it is, I checked to see if fuel was getting to the pump and it is, and I checked to see if fuel was going from the pump to the engine and it is. I'm at a loss. Does anyone have any ideas on what the problem could be? Thanks so much, Heather

Posted by on

  • ashnavishuda
    ashnavishuda Aug 21, 2012

    HYe I think it could be electrical, it fires with the throttle at idle but when you move it nothing, the radio was stolen they just cut all the wire's, I am wondering if it has damaged something in the electric's, timing is all good just put new belt on. Plenty of pressure in fuel line.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

I had a similar problem and did the same thing. I late found out it was due to a blown capacitor in the ECM (computer module). I had the ECM repaired and it has have working trouble free for a year now.
reneman..

Posted on Dec 30, 2008

  • Jackie Vitali Sep 09, 2012

    I have same similar problem, did you have it sent to someone to be fixed or did you do it yourself?

×

3 Suggested Answers

  • 6 Answers

SOURCE: will a 87 b2200 hood fit a 91 ex cab mazda b2600

Yes.

Posted on Dec 14, 2009

samtoler
  • 666 Answers

SOURCE: b2600 white smoke coming out of exhaust

i`ve never heard they are interchangeable, Are you sure its the head? i would inspect the #1 cylender a little further for a hair line crack

Posted on Jun 09, 2010

leedavidian
  • 1420 Answers

SOURCE: not sure how to remove a driveshaft from a 91 ext.

Welcome to FIxYa.com


REMOVAL AND INSTALLATION

Remove in the order shown in the figure. Install in the reverse order of removal.

I Image

1. Nut

2. Lock washer

3. Bolt

4. Nut

5. Nut

6. Lock washer

7. Bolt

8. Nut

9. Washer

lo. Nut

11. Lock washer

12. Bolt

13. Rear propeller shaft
leedavidian_15.pngleedavidian_16.pngleedavidian_17.pngleedavidian_18.png

Propeller shaft (4x2)

Before removing the propeller shaft, mark the flanges for correct installation.

Propeller shaft (4x4)

Before removing the propeller shaft mark on the front, and rear side flanges for correct

installation.

(4x2 Model)

When the propeller shaft is removed from the extension housing, immediately install the

SST into the extension housing to prevent oil leakage

B2200: 490259440

B2600i: 49 5120 440

1m a

Propeller shaft

1. Align the marks. And install the rear propeller shaft.

Tightening torque: 49-59 N.m (5.0-6.0 m-kg, 36-43 ft-lb)

2. Install the center bearing support assembly.

Tightening torque: 36-53 N.m 3.7-5.4 m-kg, 27-39 ft-lb)

3. Align the marks, and install the front propeller shaft.

Tightening torque: 49-59 N.m (5.0-6.0 m-kg, 36-43 ft-lb)


Thank you for using FixYa.com

Regards, Lee Davidian

Posted on Nov 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 Pontiac Bonneville SSEi starts and immediately dies; will not run without foot constantly on gas pedal


Well pumping the pedal on a fuel injected car does nothing. If there are no trouble codes stored in the computer, look for excessive fuel from the injectors or the fuel pressure regulator. Or lack of air thru the idle air control valve.

Mar 09, 2014 | 2000 Pontiac Bonneville

1 Answer

91 plymouth sundance died, oil on ground, check engine on


If you feel like the engine is still ok, I would look at the oil pressure and check engine light issues.
On engines with fuel injection, the fuel pump is powered by the pump relay until the engine starts. Then the engine has to have oil pressure to keep the fuel pump powered.
Its a safety feature so if you are in a wreck the fuel pump does not keep running if the engine is off.
I would want to know why the oil pressure light is staying on and what the trouble codes are in the computer.

Jan 29, 2013 | Cars & Trucks

1 Answer

Car wont stay running after it starts, runs around 500rpms then dies out,sometimes wont start. replaced fuel filter, and the main relay fuse. this problem started after replacing my gas tank.


fuel injected cars cannot vapor lock, so not the issue, when they replaced the fuel tank did they replace fuel pump? It should have been, but 2 things come to mind, they pinched wires when putting tank in and it shorts sporadically shutting off pump, look around with light and trace wires looking for any breaks in plastic coating, or fuel pump is failing.

Jun 09, 2012 | 1994 Mazda Protege

1 Answer

91 acclaim v6. starts and runs good, but once its been running for awhile (hour or so), and i turn it off, it doesnt want to start back up, or does and dies. wait 2 hours and it starts right up. recently...


Sounds like either you have a clogged fuel line and or clogged fuel filter or the fuel pump is failing. What happens when the vehicle runs the fuel pump heats up, as it heats up it produces less and less fuel for your car. Eventually ti stops working until its cool again on faulty pumps. Given the age of your vehicle I would say you need to replace both pump and filter.

Sep 19, 2010 | 1991 Plymouth Acclaim

2 Answers

Ford 460 loses power then dies. Starts back up. Idles fine.


It sounds like you might have a clogged catalatic converter on the exhaust system.

Apr 23, 2010 | 1999 Ford Super Duty F 450

1 Answer

91 s10 2.8 will not idle but will run when pumping the gas but if u give to much gas it dies ive replaced plugs wires fuel pump fuel filter air mixture censor


if fuel injected there is a solinoid that opens the air intake s o the truck will run when not pushing on the gas pedel , that is stuck shut.

Oct 24, 2009 | 1991 Chevrolet S-10

1 Answer

2500hd dies then starts and dies again


CHECK AIR FILTER FOR RESTRICTION. A BAD SUPPLY PUMP. OUT OF FUEL. BLOCKED FUEL RETURN LINE. AIR LEAK IN SUCTION LINE. RESTRICTED FUEL FILTER. INOPERATIVE FAST IDLE. LOW IDLE SPEED AND DEFECTIVE INJECTION PUMP.THIS IS A LIST OF THINGS TO CHECK.

Jul 25, 2009 | 2002 Chevrolet Silverado

1 Answer

Had my fuel pump replaced but......


hi, you might want try to change the fuel filter.

Aug 05, 2008 | 1992 Mercury Grand Marquis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

648 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...