Question about 1995 Chevrolet Lumina

1 Answer

BATTERY REMOVAL REMOVED EVERYTHING EXCEPT THE BRACE-THE BOLT ON IT WONT COME OUT- SO BENT IT OVER, BUT THE BATTERY WONT BUDGE

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 169 Answers

DID YOU REMOVE THE HOLD DOWN BOLT AT THE BOTTOM EDGE OF THE BATTERY? IT MAY BE COVERED WITH DEBRIS AND PROBABLY WON'T WANT TO COME OUT EITHER. I NEVER LIKED DOING A BATTERY IN THOSE , HARD TO GET CUSTOMER TO UNDERSTAND THE LABOR INVOLVED.

Posted on Aug 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I cannot get the belt tensioner off, have removed all bolts but still wont budge???


Shouldn't need to remove. Bolt on side that adjusts tension. Release tension buy turning bolt counterclockwise . Tensioner should move toward engine and release belt.

Mar 05, 2015 | Lexus LS 400 Cars & Trucks

1 Answer

Removal of alternator


acers757_0.gif
3.1L Engine
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt from the alternator pulley
  3. Remove the air cleaner assembly
  4. Disconnect the positive lead at the alternator by removing the nut
  5. Disconnect the electrical connector (PLIS) plug
  6. Remove the bolt (#1) connecting the rear brace to the generator
  7. LOOSEN the bolt (#7)retaining the rear brace to the exhaust manifold, (it is not necessary to remove it) move the brace aside.
  8. Remove the remaining alternator mounting bolts and remove the alternator.



Jun 13, 2011 | 1992 Oldsmobile Silhouette

1 Answer

How to install a alternator on a 94' cutlass


3.1L Engines - 1998-93 VEHICLES
(see Figures 5, 6, 7 and 8)
  1. Disconnect the negative battery cable.
  2. If necessary for access to the alternator, remove the air cleaner assembly.
  3. Remove the serpentine belt
  4. Label and detach the electrical connector(s) from the back of the alternator.
zjlimited_923.jpg

Fig. 5: After removing the serpentine belt, detach the electrical connector from the rear of the alternator

  1. Remove the rear and front attaching bolts, and unfasten the brace-to-alternator bolt.
zjlimited_924.jpg

Fig. 6: Unfasten the front and rear mounting bolts...

zjlimited_925.jpg

Fig. 7: ... then remove the brace-to-alternator bolt

  1. Carefully remove the alternator assembly, making sure all wires are disconnected.
If the alternator brace is removed, the studs must be retightened before installation or damage to the brace may result.


zjlimited_926.jpg

Fig. 8: Alternator (generator) removal and installation - 1992 3.1L engine shown (click image for zoom)

To install:

  1. Position the alternator into the mounting bracket.
  2. If necessary, attach the battery positive lead and nut to the alternator output terminal. Tighten to 71 inch lbs. (8 Nm).
  3. Install the brace-to-alternator bolt, but do not tighten at this time.
  4. Install the front and rear mounting bolts. Tighten the bolts as follows:
    1. Long bolt to 35 ft. lbs. (47 Nm)
    2. Short bolt to 18 ft. lbs. (25 Nm)
    3. Bracket bolt to 18 ft. lbs. (25 Nm)
  5. Check that tightening of the brace bolts did not bind the alternator.
  6. Attach the electrical connector(s).
  7. Install the serpentine belt
  8. If removed, install the air cleaner.
  9. Connect the negative battery cable.

Hope helps (remember to rate this answer).

Mar 23, 2011 | 1994 Oldsmobile Cutlass Supreme

1 Answer

How to change battery


  1. Disconnect the battery ground (negative) cable from the battery. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the RH fender diagonal brace. Refer to Front Fender Upper Diagonal Brace Replacement in Body Front End.
    513051.gif
    tif.gif
  3. Disconnect the battery positive cable terminal bolt from the battery.
    513047.gif
    tif.gif
  4. Remove the battery hold down retainer bolt (1).
  5. Remove the battery hold down retainer (2). Important: Do not tip the battery more than 40 degrees during removal.
  6. Remove the battery (3).
    201375.gif
    tif.gif
  7. Remove the battery insulator from the battery.
Installation Procedure

    201375.gif
    tif.gif
  1. Install the battery insulator to the battery.
    513047.gif
    tif.gif
    Important: Do not tip the battery more than 40 degrees during removal.
  2. Install the battery (3) to the battery tray.
  3. Install the battery hold down retainer (2). Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  4. Install the battery hold down retainer bolt (1). Tighten
    Tighten the battery hold down bolt to 18 N·m (13 lb ft).

    513051.gif
    tif.gif
  5. Connect the battery positive cable to the battery. Tighten
    Tighten the battery positive terminal bolt to 15 N·m (11 lb ft).
  6. Install the RH fender diagonal brace. Refer to Front Fender Upper Diagonal Brace Replacement in Body Front End.
  7. Connect the battery negative cable to the battery. Tighten
    Tighten the battery negative terminal bolt to 15 N·m (11 lb ft).

Nov 11, 2010 | 2000 Chevrolet Monte Carlo

2 Answers

HOW DO I REMOVE A ALTERNATOR ON A 1987 CHEVY BLAZER


REMOVAL & INSTALLATION
  1. Disconnect negative battery cable, then disconnect the positive cable from the battery.
  2. Disconnect and tag all wiring to the alternator. Fig. 1: Some of the alternator wiring is at a ring terminal located under a protective rubber boot on the rear of the alternator 85773154.jpg
    Fig. 2: A small box or open-end wrench may be used to loosen the wiring retaining nut 85773155.jpg
    Fig. 3: Squeeze the locktab and disengage the connector from the side of the alternator housing 85773156.jpg

  3. If necessary for removal clearance, disconnect the ground strap from the alternator bracket.
  4. If equipped, remove the alternator brace bolt.
  5. If the truck is equipped with power steering, it may be necessary to loosen the pump brace and mount nuts.
  6. Remove the lower mounting bolt, then support the alternator and remove the upper mounting/adjusting bolt.
  7. Slip the alternator belt from the pulley and remove the alternator from the truck. Fig. 4: Loosen the lower mounting bolt 85773159.jpg
    Fig. 5: The alternator uses a very long lower mounting bolt which passes through the alternator housing and a bushing before threading into the engine block 85773160.jpg
    Fig. 6: Support the alternator by hand and unthread the upper mounting/adjustment bolt 85773161.jpg

  8. Installation is the reverse of removal. Be sure that the bushing is in place when the lower mounting bolt is installed. Should the bolt be torqued without the bushing in position, alternator housing damage would likely occur.
  9. Adjust the belt(s) to have 1?4 - 1?2 inch depression under thumb pressure on its longest run. Fig. 7: Once the alternator is free, it may be lowered slightly so the belt may be removed from its pulley 85773162.jpg
    Fig. 8: Remove the alternator housing from the vehicle by lifting upward 85773163.jpg
    Fig. 9: During installation, carefully pry outward on the alternator in order to adjust the belt tension 85773164.jpg
    Fig. 10: Alternator mounting, in-line 6 and gasoline V8 engines 85773007.gif
prev.gif next.gif

Sep 24, 2010 | 1987 Chevrolet Blazer

1 Answer

How do you remove the battery from a 2002 jeep grand cheroke? I disconnected the cable ends, however their seems to be a brace at the bottom of the battery that stops it from being removed. Attempting to...


thats the battery hold down its a 13mm bolt with the hold down wedge against the battery you have to remove the bolt or loosen it enough to get the battery free spray some penetrating oil on it and let it soak a couple of hours hope this helps

Jul 26, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Alternator removal/ford taurus 1996


Generator Removal
  1. Disconnect the battery ground cable.
  2. Remove the accessory drive belt from the generator pulley.
  3. Remove the power steering line bracket and heater hose support bracket from the generator.
  4. Remove the upper generator bolts.
  5. Partially raise the vehicle on a hoist.
  6. Remove the right front wheel.
  7. Remove the lower fender splash shield retainers and position the shield out of the way.
  8. Remove the generator splash shield.
  9. Raise the vehicle.
  10. Disconnect the electrical connector and remove the battery positive cable from the generator.
  11. Position an adjustable stand to the subframe.
  12. Remove the right subframe bolts.
  13. Remove the lower generator bolt.
  14. Lower the subframe to provide clearance.
  15. Remove the generator
Generator — 3.0L (2V) and 3.0L (2V) FF Engines
  1. NOTE: The generator (GEN) (10300) is not internally serviceable.

    Disconnect battery ground cable (14301). Refer to .
  1. Disconnect the electrical connectors from the integral generator/voltage regulator.
  1. Loosen the generator pivot bolt. Remove the mounting brace bolt from the generator.
  1. Disengage the accessory drive belt (8620) from the generator pulley (10344).
  1. Remove generator brace.
  1. Remove the generator pivot bolt and generator/voltage regulator.

524109a.gif

Mar 01, 2010 | 1996 Ford Taurus

1 Answer

Replacing the alternator


Fig. : Alternator mounting-2.2L engine

efa282c.jpg

REMOVAL & INSTALLATION

(2.2L Engine)
  1. Disconnect the negative battery cable.
  2. Raise and support the front of the vehicle, then remove the passenger side tire and wheel assembly for access to the rear of the alternator through the wheel well.
  3. Working through the wheel well, unfasten the alternator brace-to-block bolt, then remove the brace-to-intake nut and the brace-to-engine stud nut.
  4. Unplug the alternator wiring connector, then remove the battery terminal nut and wire.
  5. Carefully release the serpentine belt tension and remove the belt from the alternator pulley. Do not allow the tensioner to snap back into position once the belt is off the pulley.
  6. Loosen the alternator retaining bolts, then support the alternator and remove the fasteners. Remove the alternator from the vehicle.

To install:
  1. Position the alternator in the vehicle and loosely install the retaining bolts.
  2. On 1994-98 models, tighten the top alternator bolt to 22 ft. lbs. (30 Nm) and the bottom bolt to 32 ft. lbs. (43 Nm).
  3. On 1999-99 models, tighten the rear bolt to 37 ft. lbs. (50 Nm) and the front bolt to 18 ft. lbs. (25 Nm).
  4. On 1994-98 models, install the alternator brace, then tighten the retaining nut(s) and bolts to 22 ft. lbs. (30 Nm).
  5. On 1999-99 models, install the alternator brace, tighten the brace-to-alternator and brace-to-intake retainers to 18 ft. lbs. (25 Nm). Tighten the brace-to-engine stud nut to 37 ft. lbs. (50 Nm).
  6. Install the battery terminal wire and tighten the retaining nut, then engage the alternator wiring connector.
  7. Hold the serpentine drive belt tensioner, back off the belt while slipping the belt over the alternator pulley. Gradually lower the tensioner into contact with the belt, then check for proper alignment and tension.
  8. Connect the negative battery cable.



Fig. : Alternator mounting-4.3L engine


3fdb6af.jpg

REMOVAL & INSTALLATION
(Except 2.2L Engine)
  1. Disconnect the negative battery cable.
  2. Remove the air inlet duct assembly, if necessary.
  3. Carefully relieve the serpentine drive belt tension, then remove the belt from the alternator pulley. Do not allow the tensioner to snap back into position once the belt is off the pulley.
  4. Remove the nut retaining the radiator hose brace to the back on the alternator.
  5. If equipped, unfasten the retainers, then remove the brace from the engine and/or the alternator.
  6. Disconnect the battery terminal boot wiring from the back of the alternator, then unplug the regulator wiring connector.
  7. Support the alternator and remove the mounting bolts (usually 2) from either side of the alternator, then remove the alternator from the vehicle.
To install:
  1. Position the alternator in the vehicle and loosely install using the mounting bolts.
  2. If equipped, loosely install the brace to the engine and/or alternator.
  3. Tighten the left or front alternator retaining bolts to 36 ft. lbs. (50 Nm), the right or rear alternator bolt to 18 ft. lbs. (25 Nm), the brace bolt to 18 ft. lbs. (25 Nm) and/or the brace nut to 22 ft. lbs. (30 Nm), as applicable.
  4. Connect and secure the alternator wiring.
  5. Carefully relieve the serpentine drive belt tension and position the belt over the alternator pulley, then slowly release the tensioner into position.
  6. If equipped, install the air inlet duct assembly.
  7. Connect the negative battery cable.

I hope helps with this. Good luck (remember rated this help).

Jan 05, 2010 | 1998 Chevrolet S-10 Pickup

2 Answers

How do I install starter for 2000 GMC Sonoma. This is a 4 cyl 2 wheel drive pick-up


e
Removal & Installation
2-Wheel Drive
- 2.2L Engine
  1. Remove or disconnect the following:
    Negative battery cable Front exhaust pipe, if necessary for access Starter heat shield, if equipped Brace rod from the front of the engine and the bell housing Drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well Wires from the starter solenoid Attaching bracket-to-engine mount bolt Starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you. Starter and shims (if equipped) from the vehicle Bracket from the starter assembly, if equipped

    e12f2d1.jpg

    Fig. Starter motor and related components - 2.2L engine

To install:
  1. Install or connect the following:
    Bracket to the starter, if removed. Tighten the bracket nuts to 97 inch lbs. (11 Nm). Starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position. Bracket-to-engine mount bolt (loosely), if equipped Starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm) Wiring to the solenoid Brace rod and tighten the retainers Front exhaust pipe and tighten the fasteners, if removed Starter heat shield, if equipped Driver-s side wheel, if removed Negative battery cable

Hope helped with this (remember rated this help) Good luck.

Nov 18, 2009 | 2001 GMC Sonoma Extended Cab

Not finding what you are looking for?
1995 Chevrolet Lumina Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...