Question about 1986 Chrysler Fifth Avenue

1 Answer

Caburator adjustment I just had my carburator rebuilt and can't figure out how to adjust it. I know I need a tool, but where do you adjust it? Thanks for any help.

Posted by on

1 Answer

Should be some screws and the side

Posted on Aug 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I got a problem on a caburaror on aselerate truck 87 dodge


Idles, automatic chokes, and kick down idles must be adjusted. You cannot just install a carburetor rebuilt or new without making idle and linkage adjustments to match the engine requirements. Does it have an idle solenoid adjustment and kick down adjustment, double barreled?. Did you get new springs for linkage? Have a mechanic make the adjustments. Find an older mechanic that knows carburetors.

Feb 12, 2015 | Dodge Cars & Trucks

1 Answer

WHY DOES TRUCK HESITATE WHEN GIVING GAS AND STALLS


Is it carburator? I had the same problem with mine 85 ford ranger. I had the carburator rebuilt but it still took the shop 3 tries before they got the adjustment right. It's either your fuel pump (most likely). Inside the carburator, there's a float that adjust to much gas is needed and that could also be the problem. The float might be defective so it stalls when you step on the gas. I suggest replacing the fuel filter as well if you gonna work on it
Other unlikely culprit could be your ignition wires/coil/spark plugs. Check to see when they were last replaced.....
good luck

Apr 09, 2012 | Cars & Trucks

1 Answer

Rebuilt carburator and truck runs rich. Cant get adjusted right and under accelereation truck boggs down


im pretty sure that the float adjustment is set wrong, if to high it will act as if truck is flooding out, and be very rich. if to low you will not get the power you need. readjust float level. make sure there is no dirt inside carburator. for adjustment turn screws way in and back out 1 and a half turns.start from there.

Jun 03, 2010 | 1985 Nissan Pickup

1 Answer

How can you adjust the carburetor on a 1987 GMC safari van V-6


If the carburator has never been rebuilt, or the plugs that were installed at the factory have never been removed, you need to remove those plugs, there is one for each idle mixture screw, at the front of the base plate on the bottom of the carburator, 1 for the TPS adjustment on the driver side front of the carburator, and one for the mixture control solenoid on top of the carburator, in the middle, towards the front.

May 22, 2010 | 1987 GMC Safari

3 Answers

I have a 66 ford mustang 1 barrel carburator


when the engine is fully warmed up check the choke. it should be wide open.if not it needs to be adjusted.

Apr 23, 2009 | 1966 Ford Mustang

2 Answers

Carborator not getting gas


If you have fuel in line make sura how is your fuel filter, if the fuel fiter geting fuel from the fuel pump then and no fuel coming into carburator remove the head part of the caburator some scerws on then taked out you will see foult chamber remove the flout chamber careful needle valve coming out then take screw driver remove needle holder then you will see filter which is blocked fuel to inter the caburator.

1- you need kit of caburator parts you can get new filter.
change all gaskets top and poton of the caburator.

Dec 03, 2008 | 1990 Toyota Pickup

1 Answer

Carburator adjustment


a friend. Thanks though.

Aug 17, 2008 | 1986 Chrysler Fifth Avenue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...