Question about 1995 Toyota Pickup

1 Answer

Ignition switch truck ignition won't turn, won't let me start. got another switch key still froze up again. Was running fine for 11 years and all of a sudden it locked up.

Posted by on

  • Kathy Luersen Aug 17, 2008

    Ya, We will look at that in the morning. That IS part of the switch. We are replacing the whole thing. 1st got wrong switch for standard 2nd got one that worked b4 we put on did not line up. soooooo we gotta try another.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 298 Answers

Sounds like you steering wheel lock is wearing out.

Posted on Aug 17, 2008

  • kristopher betzler
    kristopher betzler Aug 17, 2008

    ok, let me know if you have any issues.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Where is the body control module located in 2002 gmc envoy?


It's under your back seat. See here for picture http://www.ebay.com/itm/like/261068608953?lpid=82
Here is the relearn procedure which you have to perform so the new BCM will recognize your key and start the car:
For those vehicles that use a BCM, the BCM can learn the resistance value of the existing key by using the relearn process. In order for the vehicle to start, the BCM (as well as the Passkey module in other vehicles) must identify the resistor pellet in the key, then the BCM sends a password to the PCM. If this password matches the password stored in the PCM, the system enables fuel delivery. So you can see that if either the BCM or PCM are replaced, a relearn procedure is necessary. This same relearn procedure can be used if an ignition key with a different resistance value is used to replace the existing key. Before beginning the relearn, make sure there is a fully charged battery in the vehicle, and both the BCM and PCM are properly powered up and in communication with each other. Now you're ready to initiate the relearn procedure.

1. First, insert the ignition key and turn the ignition switchto the "On" position (Do not start the engine). Leave the switch on for 11 minutes. The security light may flash or be on steady during this 11 minute period. Make sure the light is no longer on or flashing before proceeding to #2 .
2. Turn the ignition switchoff for 30 seconds.
3. Turn the ignition switchto the "On" position (as in step #1) for 11 minutes again.
4. Turn the ignition switchoff for another 30 seconds.
5. Turn the ignition switchto the "On" position for 11 minutes a third time.
6. Turn the ignition switchoff for 30 seconds one final time.
7. Turn the ignition switchto the "On" position one final time and wait 30 seconds.
8. Attempt to start the engine. If the engine starts and runs normally, the relearn is complete. If the engine does not start, check for trouble codes and address them before attempting the relearn procedure again.
You can pick one oif these up for $20 or less at a junkyard. For those vehicles that use a BCM, the BCM can learn the resistance value of the existing key by using the relearn process. In order for the vehicle to start, the BCM (as well as the Passkey module in other vehicles) must identify the resistor pellet in the key, then the BCM sends a password to the PCM. If this password matches the password stored in the PCM, the system enables fuel delivery. So you can see that if either the BCM or PCM are replaced, a relearn procedure is necessary. This same relearn procedure can be used if an ignition key with a different resistance value is used to replace the existing key. Before beginning the relearn, make sure there is a fully charged battery in the vehicle, and both the BCM and PCM are properly powered up and in communication with each other. Now you're ready to initiate the relearn procedure.

1. First, insert the ignition key and turn the ignition switchto the "On" position (Do not start the engine). Leave the switch on for 11 minutes. The security light may flash or be on steady during this 11 minute period. Make sure the light is no longer on or flashing before proceeding to #2 .
2. Turn the ignition switchoff for 30 seconds.
3. Turn the ignition switchto the "On" position (as in step #1) for 11 minutes again.
4. Turn the ignition switchoff for another 30 seconds.
5. Turn the ignition switchto the "On" position for 11 minutes a third time.
6. Turn the ignition switchoff for 30 seconds one final time.
7. Turn the ignition switchto the "On" position one final time and wait 30 seconds.
8. Attempt to start the engine. If the engine starts and runs normally, the relearn is complete. If the engine does not start, check for trouble codes and address them before attempting the relearn procedure again.

Dec 13, 2014 | 2002 GMC Envoy

1 Answer

Randomly won't start or even turn over, sometimes start fine. bouncing gauges


Yes it could be the key switch. You would need to check for power at the starter when it fails to crank. There is also a neutral safety switch in the circuit.

Dec 24, 2012 | 1995 Nissan Pathfinder

1 Answer

Resetting the passlock


1. First, insert the ignition key and turn the ignition switch to the "On" position (Do not start the engine). Leave the switch on for 11 minutes. The security light may flash or be on steady during this 11 minute period. Make sure the light is no longer on or flashing before proceeding to #2 .
2. Turn the ignition switch off for 30 seconds.
3. Turn the ignition switch to the "On" position (as in step #1) for 11 minutes again.
4. Turn the ignition switch off for another 30 seconds.
5. Turn the ignition switch to the "On" position for 11 minutes a third time.
6. Turn the ignition switch off for 30 seconds one final time.
7. Turn the ignition switch to the "On" position one final time and wait 30 seconds.
8. Attempt to start the engine. If the engine starts and runs normally, the relearn is complete. If the engine does not start, Go to this link for info
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Sep 08, 2012 | 2000 GMC Yukon Denali

2 Answers

Car won't turn over randomly


When it will not crank, a mechanic would check for voltage at the starter, the clutch safety switch, and the key switch.

Aug 03, 2012 | 2001 Honda CR-V

1 Answer

2004 pontiac grand prix going down highway and car shuts off. Pull over try to start, cranks over fine just no fire at all. Let sit for 10 minutes with key in on position, then turn off key and then it...


yes very much possible the ignition switch is getting Short so its causing the issue.Check the voltage at ignition switch.The power wire to the ignition switch harness are connected to battery and will give 12 volts.If there is no voltage then its loose connection.If there is short the voltage will differ. ---------thanks.Helpmech.

Feb 24, 2011 | 2004 Pontiac Grand Am

1 Answer

I replaced fuel pump and relay switch Sometimes when you turn key you can hear relay switch clicking and pump working then truck satarts, Runs fine . Try start it again and it just turns over , there's...


not knowing what kind of vehicle it is it is hard to tell. some gm cars and trucks have oil sending units that will not allow the vehicle to start unless it has oil pressure. they start going out and sometimes they start and sometimes they won"t.

Dec 08, 2010 | GMC Sonoma Cars & Trucks

2 Answers

My 95 chevy camaro starting issue


sounds like its the ignition switch.the grinding noise you hear is probably the starter still engaged. thanks jeff

Nov 30, 2008 | 1995 Chevrolet Camaro

2 Answers

1999 Olds ignition switch problems


Hi....
In your Intrigue to use the New Passcode sensor .
You need to program the new Passcode to the ECM. of the Vehicle.
This is a prosses that involve around 30 minutes maybe a little more.

Remove the old Ignition switch.
Install the new Ignition switch. with the new Passlock sensor.
Turn the key to on position and try to start a few senconds. them leave the key on run position.
For 10 minutes and NOT more than 11 minutes.
Them turn the key to OFF position for exactly 30 seconds.
Them turn the key to Run position 10 minutes or 11.
them turn back the key to OFF position for 30 seconds.
Them turn the key to Run position 10 minutes or 11,
Turn the key to OFF position and wait 1 minute, them try to start the vehicle.
If the car start you are DONE.
But if Not Letme know to give you more information.

OK I hope this help to try solve your problem.

Thank you for use fixya...

Nov 15, 2008 | 1998 Oldsmobile Intrigue

Not finding what you are looking for?
1995 Toyota Pickup Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...