Question about 2006 Chrysler Town & Country

3 Answers

Sliding door power door locks

I am not able to get the power door locks to work on the sliding doors. The left door started showing the problem a couple of weeks ago and now both doors are not responding to the key fob or the switch on the front doors. The front doors and the liftgate work with no problem.

Posted by on

  • tlbro11 Aug 20, 2008

    I am not able to get the power door locks to work on the sliding doors. The left door started showing the problem a couple of weeks ago and now both doors are not responding to the key fob or the switch on the front doors. The front doors and the liftgate work with no problem. I have replaced the IOD fuse and checked all the other fuses. I have also checked the switches.

×

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 958 Answers

Sliding doors usually connects with the car's electrical thru contacts on the sliding door to the stationary part of the car near the locks. they should be clean and shiny to have a prfect contact.

if they are ok, you have to open the door panels and check the solenoids of the locks manually. if you would know how to apply power to the solenoids to check them if they are responding. if they are then the problem is the supply.

you have to trace the power that goes to the terminals then to the solenoids.

i hope i was able to fix ur problem.

tnx 4 using fixya,

drcool

Posted on Aug 20, 2008

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,051 Answers

You may also want to check the fob sensor mine went bad in my astro van

Posted on Aug 20, 2008

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 623 Answers

Check for blown fuse and wires

Posted on Aug 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Electronics


Reseting the power sliding door gm Montana or venture? In: Chevy Venture, Pontiac Montana [Edit categories]
[iframe style="BORDER-BOTTOM: 0px; BORDER-LEFT: 0px; VERTICAL-ALIGN: bottom; BORDER-TOP: 0px; BORDER-RIGHT: 0px" id=google_ads_iframe_/51859126/answ_desktop_question_answered_600x300_alt_0 height=300 marginHeight=0 src="javascript:"[/iframe]
Answer:

It's in the owners manual under power door. I believe you pull the fuse under the hood for 15 sec with the overide switch in the off position. ...(roesterman adds...).My power door was opening all the way then closing immediately. I used this method to reset door and it worked! This started happening after I had some body work done to vehicle..maybe they disconnected battery or something. Delay locking was locking doors before slider was closing too. This left the door unlocked. I haven't tested to see if this has been corrected by reset yet.

Apr 06, 2014 | 2002 Pontiac Montana

1 Answer

2005 Saturn Relay power doors don't work rear hatch locked shut...help


its alot going on if all that started happening at one time check the bcm. body control module.

Dec 02, 2012 | 2005 Saturn Relay

1 Answer

The power side passenger door for a 2001 Chevy Venture van works every so often. The door doesn't move when the button is pressed on the panel in the headliner. The key remote doesn't work most of the time...


The proper way would be to look at a wiring diagram an test the electrical circuit's with a DVOM - digital volt ohm meter . Do you know how to test automotive electrical circuit's ?
Electric Testing Techniques You Need to Know
The Trainer 32 How To Read An Automotive Block Wiring Diagram
Free wiring diagrams here http://www.bbbind.com/free_tsb.html
Enter the vehicle info. year , make model and engine size . Under system click on body & accessories ,then under subsystem click on power sliding door . Click the search button then the blue link. Looking at the diagram you will see a control module is used .
Also reading factory service info. on how it works would be a good idea.

Rear Side Door Actuator Control Module
The rear side door actuator control module is capable of on-board diagnostic functions described in On-Board Diagnostic Features . The rear side door actuator control module monitors the door position at all times including during manual operation. After activating the on-board diagnostic modes, loosing battery voltage, or ground to the rear side door actuator control module the Power Sliding Door (PSD) Re-Initialization procedure must be performed in order for the rear side door actuator control module to correctly determine the door position.
Power Sliding Door System Description
The power sliding door system(s) can operate correctly only if the power sliding door is in proper mechanical condition. Any mechanical problems will affect the power sliding door operation and must be repaired before attempting to diagnose the power sliding door system. Manually open and close the power sliding door to determine if the door moves smoothly and without excessive resistance or binding. The power sliding door must also latch and unlatch without the use of excessive force. At any time during power sliding door open or close operation, excessive resistance to the door movement will cause the power sliding door to stop and reverse the direction of travel.
The power sliding door will operate only when the power sliding door on/off switch in the overhead console is in the on position. At anytime during power sliding door operation the on/off switch may be turned to the off position and the system will quit any function in process. The power sliding door will not open unless the transmission shift lever is in the park position and the door is unlocked. When the sliding door security lock is in the locked position the power sliding door will not open from the inside. The power sliding door close function will operate when the vehicle is in gear. The power sliding door module uses the VSS signal to determine if the vehicle is moving during a power sliding door close function. The momentum of the vehicle moving forward adds resistance to the door closing operation. When the rear side door actuator control module determines the vehicle is moving forward while closing the door, current flow through the actuator motor is increased instead of being reversed. The VSS signal circuit is supplied battery positive voltage through a resistor then monitored within the rear side door actuator control module. The VSS signal circuit is then pulsed to ground, or pulled low by the powertrain control module in relation to vehicle speed. The sliding door alarm will sound repeated short tones whenever the power sliding door system is turned on and the door is open while the transmission is out of park.
When the power sliding door system is on and manual operation of the power sliding door is detected the rear side door actuator control module activates the power assist feature. When the power assist is activated the power sliding door will continue to open or close without any further manual effort.
The power sliding doors may be operated using the Remote Keyless Entry System. The keyless entry transmitter will have one OPEN/CLOSE button with a van symbol on it for each power sliding door. The power sliding door ON/OFF switches in the overhead console must be in the ON position in order to operate the power sliding doors using the keyless entry transmitter. When a right hand power sliding door OPEN/CLOSE function is activated using a keyless entry transmitter the exterior lights will flash once indicating the RKE module has received the OPEN/CLOSE command. When activating a left hand power sliding door OPEN/CLOSE function with the keyless entry transmitter the exterior lights will not flash.

On-Board Diagnostic Features
The left and right power sliding door systems operate as independent systems. The on-board diagnostic modes are entered and operate the same in both systems.
The power sliding door systems are capable of the following on-board diagnostic functions:
• Diagnostic Mode 1: An audible signal indicates the diagnostic trouble codes stored by the rear side door actuator control module.
• Diagnostic Mode 2: An audible signal indicates when inputs to the rear side door actuator control module are active.
• Diagnostic Mode 3: Performs an output test of the sliding door unlatch actuator.
Entering On-Board Diagnostics
The on-board diagnostic modes can only be entered in a sequential order from modes 1-3.
• Enter the right power sliding door system on-board diagnostics using the right B-pillar open/close switch and the right on/off switch in the overhead console.
• Enter the left power sliding door system on-board diagnostics using the left B-pillar open/close switch and the left on/off switch in the overhead console.
1. Both power sliding doors must be closed and in the latched position.
2. Place the ignition switch in the OFF position.
3. Place the on/off switch in the overhead console to the OFF position.
4. Press and hold the B-pillar power sliding door open/close switch.
5. While holding the open/close switch, operate the on/off switch through 10 ON and OFF cycles within 10 seconds stopping in the on position.
6. The sliding door alarm will sound 1 long tone indicating diagnostic mode 1 is active.
Diagnostic Mode 1
Upon activating diagnostic mode 1, DTCs will begin to be signaled by the sliding door alarm. The DTCs are 2 digit codes and the codes are represented by the number of buzzes for each digit of the code number. For example a DTC 12 is represented with the following sequence: buzz, pause, buzz, buzz, long pause. Each DTC will be signaled 3 times before proceeding to the next DTC. Refer to Diagnostic Trouble Code (DTC) List . The DTCs will continue to be repeated in this manner until the on-board diagnostics are exited or mode 2 is entered. When exiting the on-board diagnostics all stored DTCs will be erased from the rear side door actuator control module memory.

Oct 13, 2017 | 2001 Chevrolet Venture

1 Answer

I have a 99 montana passenger side sliding door dont work. Hit either button all it does is clicks and motor seems to be fine.. I went to junk yard bought complete new motor and everything that comes...


I would check the overhead buttons there are two one opens the door, and the other beside it that shows the van crossed out, disables the electric sliding door feature. try playing with that, Also remember, that vehicle must be in PARK for the electric sliding door to open. Make sure the power lock on that door is working, and check the child safety lock when you have it open by the doors catch. Hope that Helps You.

Aug 02, 2009 | 1999 Pontiac Montana

2 Answers

2001 Oldsmobile Silhouette....Power lock on my power door doesn't come up completely and the door doesn't open with or without the button. What can I do? I also believe my van has other electrical issues...


From the back of the front door slide your hand in the sliding door crack and find the child-safety-lever. Push the lever up and/or down while moving the sliding door manual lock/unlock button to the up position. Also works on the non-powered sliding door.

Jul 15, 2009 | 2001 Oldsmobile Silhouette

1 Answer

2006 Dodge Caravan - ONE power door lock stopped working


i have replaced many sliding door lock actuators on these vehicles..dealer part..mostly on passenger side sliding door..also possible you have a broken wire in door track harness..follow wiring from door into what looks like a plastic chain in door track at door opening

Apr 30, 2009 | 2006 Dodge Caravan

1 Answer

Left side sliding door-the track is completely missing


You are going to have to replace the track and the lock is probably the switch that unlocks the door on that particular side. The lock is connected to a rod that pulls the lock lever open. This is probably broken and got stuck inside. You will have to remove the door paneling to check these components. you can buy parts at Car Part . com online . Maybe they have them If not there are a hundred other sites.like Automotive warehouse. com

Nov 24, 2008 | 2002 Chrysler Town & Country

9 Answers

2005 Toyota Sienna Sliding Door Won't Open


Have 2005 Sienna and its Driver side door was not openning. Cheap dealer fixed it himself in front of me. After opening the doors plastic assembly while sitting inside with a screw driver. Then he bent the clip towards left where the metal wire is connected. If you guys want to see what he did i would record a video and upload for you guys. Let me know at xahid2000@yahoo.com

Jul 22, 2008 | 2005 Toyota Sienna

Not finding what you are looking for?
2006 Chrysler Town & Country Logo

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...