Question about 2003 Chevrolet Venture Passanger

1 Answer

Door panels how do you get door pannels off properly

Posted by on

  • dsf09 Jan 24, 2009

    where are the screws located on the door panel? I have found one under the arm rest. I am sure that there are more

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 30 Answers

You will need some type of flat tool to start this. The door panels are held on by clips inside and they need to be popped out, but this can be tricky to not damage the panel in the process. There are special Trim & upholstery tools that are flat kinda wedge shapes that are plastic for prying these up and they are fairly cheap (can pick some up for about $6 at places like Harbor Freight) or what I commonly did before buying those tools is wrap a wide flathead screwdriver with a rag and push underneath panel and then pry up to pop up that first one, then you can get your fingers underneath it to pull around edges until you get them all. As soon as you get all the clips off you will need to disconnect the window/lock electrical connectors to completely remove the door panel.

Posted on Aug 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gas release button fell inside the door


You will need to remove the door panel to retrieve your part. There are 4 screws at the bottom of the door pannel the are either torx or philips (I have seen both) remove those bolts, the tweeter cover and you will need to seperate the 2 halves of the pull handle (look close and you will see the split, use a small flat screwdriver) remove the 2 torx bolts. Pull out on the door panel to pull out the door panel clips that secure it to the door but not so hard as to break the upper part. Once all clips are out of the door, pull up to get the pannel off of the door. Then disconnect wiring if you want to completely remove the panel and set aside. I believe that is all the bolts to get the panel off, it's been a little while since I took a door panel off. Hope this helps.

Dec 28, 2011 | 2003 Volkswagen Jetta TDI

1 Answer

Thow to take off door pannel and install passenger side window motor on 2000 jeep grand cherokee


first you have to remove dead plugs on door handle and remove screws another screw on door opening handle and you have to disconnect 2 metal pins behind that and look all around the door panel sides and under should have several rivets make sure no any screw and rivets left on door panel pull door panel foward and pull it up dont go too hard dont damage door panel conections for proper reinstallation. before removing door panel from the door dont forget disconnect cable connections from window and door lock switches.good luck

May 07, 2011 | 2000 Jeep Cherokee

1 Answer

How do i remove the wing mirror (power adjust & power fold) on the ford f250 super duty?


Roll the window down first, you will need 2 hands. Pull the small cover off that is at the top front of the door pannel. You will then disconnect the wire connector and remove the three 11mm nuts that are holding the mirror in place. Pull mirror out and replace.

If you dont have just that little pannel you will have to remove the door pannel. If you dont have power windows pull the cover out on the window crank and move it to the side, there will be a screw holding the crank in place. Remove it. If you do have power windows remove the window control switch plate (it will just pop up using a small screwdriver) and disconnect the wires. If equipped, remove the front door trim panel reflector or the courtesy lamp lens. Then remove the screws. DO NOT pull directly outward on the door pannel, something will brake. Remove the front door trim panel by pulling it straight upward.Lift and remove the front door trim panel. Then the nuts holding the mirror will be visible, remove and replace the mirror.

Dec 07, 2010 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

I have a 1999 Buick century custom i bought new door speakers for it and i need instructions on how to get my driver and passenger door panel off and what tools needed to complete the job


hi, i will try and help. the door pannels have hiden screws the electrical pannels usually pop out with a small screw driver (FLAT) the handle has a strip of plastic removed by placing screw driver into the join, then the handle has (2) or (3) screws. the pannel has popets near the bottom and screws under the door tray (4). that the best i can do sorry. gerry

Sep 10, 2010 | 1999 Buick Century

1 Answer

I need to remove the interior door panel from my 1990 olds delta 88. How do I locate the screws, holding clips etc. so I don't damage the interior covering of the door


most of the screws will be located at or near the armreast and under the map popcket on the lower door (if it has one) just work gingerly in pulling off the pannel using the proper tool. If you take your time you will find all of them work slowly and look before you pull. There are clips at the top of the door that are holding it in place to remove the pannel you will have to move it in an upward direction.

Feb 16, 2010 | 1990 Oldsmobile Eighty Eight

1 Answer

Door will not unlock with handle from inside


inner door pannel ??????
it is likely glued on or if it is metal then it is welded
plastic is the usual thing behind plastic pannel
pick up a chilton book and look it over
or ask dealer for copy of door break down from there chilton book

Jan 22, 2010 | 2004 Volkswagen Passat

1 Answer

Need to fix drivers side door , need to remove inside panel on door


Usually a few screws on the handle etc. When they are removed all that is left holding the pannel are pull clips carefully push a flat scredriver between the pannel and the door pry carefull until one or two snap open you should then get your hand behind the pannel then a sharp pull will remove it.

Aug 05, 2009 | 2001 Ford Explorer Sport Trac

2 Answers

Replacing passenger side mirror


no the door pannel does not need to come off but there is a triangle shaped plastic trim pannel above the door pannel that needs to be removed to access the mounting bolts.

May 28, 2009 | 2003 Nissan Xterra

1 Answer

1999 Rodeo Electric Windows Switch Panel - Drivers Side


gotta remove the door panels there a panel removing tool looks like a snakes tounge but bigger these pop out your door pannel
they take the panel pins out without damageing the door pannel
disconnect electric switches

the electric assembly in side is rivited in so is your going to remove gears you need to drill out revits then work it out of door panel

May 28, 2008 | 1999 Isuzu Rodeo

Not finding what you are looking for?
2003 Chevrolet Venture Passanger Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...