Question about 2001 Jeep Grand Cherokee

1 Answer

Replacing break caliber on jeep garnd cherokee

Posted by on

  • robertwilk896 May 30, 2011

    Whats your problem Ill help you get er done

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 165 Answers

Make sure you bleed it properly

Posted on May 30, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replacing brake caliber cant get bolt loose


Use WD-40 rust inhibitor spray. Let it soak for a while,repeat a few times and it should break loose.

Dec 17, 2013 | 2004 Jeep Grand Cherokee

1 Answer

What is cost to replace breaks on 2000 jeep cherokee


around 30 to 60 dollars depending on what quality break pad you want or the longer you want them to last.

Apr 12, 2012 | 2000 Jeep Grand Cherokee

1 Answer

Replace rear rotors 2004 jeep cherokee


Heres what you will need to do this type of job. First you will need a rachet and metric sockets with an extention if available. Also you will need somthing to press the caliber piston back into place a special tool or some kind of press would work . A plastic auto hammer to knock the rotors loose, somtimes they can be difficult to remove. Pliers would be needed as well as a screw driver to help mount the caliber or pads back into place. One thing to keep in mind is that if you indeed are replacing the rear rotors, it is recommended to get new pads as well. This is for the reason that old pads will cause break sqealing since they are not surfaced perfectly straight for the new rotor. Step one will be to get the caliber of the vehicle so if there is a medal clip on one of the studs just use the pliers to rip it off. Then use the rachet to remove two bolts holding the caliber. After you remove those bolts, there should be another two bolts holding the caliber bracket as well, do the same procedure in removing those. IMPORTANT do not let the caliber hang by the brake cable, put it on a stand or in a location where it is not free fall hanging. Now you should just have the rotor left, try pulling on it to see if it breaks loose, if not then use your plastic hammer to bang in the back of the rotor and knock it loose that way. If I remember correclty those rear rotors will have brake shoes underneath. Do not wory about those they are there for your emergency brakes. Now put the new rotor on and make sure it is securley installed on the wheel hub. Install you'r bracket first, then begine to install your caliber back into place. NOTE the caliber may not install to easy onto the rotor for the reason that you will need to compress the piston inside with either the special tool or some type of press. If you compress it and you hear brake fluid dripping down, it is nothing to worry about, its just the fluid being pushed back by pressure. Install the caliber and pads the same way as removal paying close attention to the other side if your not sure of how the originally were installed. When all this is finished look up brake bleading on YOUTUBE.com to accurately bleed your brakes and remove any air inside that may cause spongy or moister inside your brake lines.

Hope this Helps!

Jun 07, 2011 | 2004 Jeep Grand Cherokee

1 Answer

2005 jeep garnd cherokee rocky mountain edition is just blowing cold air.I will not heat up untill you drive the vehicle. Any suggestions?


If the temeperature gauge says the engine is warm but the air is not warm until you drive it would most likely it would be the heater core partially clogged. Have it flushed.


Please take a moment to rate my answer .........Thanks

Dec 01, 2010 | 2005 Jeep Grand Cherokee

1 Answer

How do I replace pulley bearings on my jeep garnd cherokee? Is there any settings in tensions I need to know?


Hi Josh,
I'm glad you were able to diagnose it as a pulley. For pulleys you don't replace the bearings. Replace the complete pulley. Just remove the
bolt(s), take the old pulley off, bolt on the new pulley and put the belt back on. Nothing technical you need to do here. Just tighten the bolt(s) to about the same tightness they were before you removed them.
I hope this helps.

Mar 26, 2010 | 1996 Jeep Grand Cherokee

2 Answers

Where is the fuse box on 1997 jeep garnd cherokee


Behind a panel near the floor on the front passenger side

Jan 28, 2010 | 1997 Jeep Grand Cherokee

1 Answer

1997 Jeep Garnd Cherokee had battery go dead. Once boosted it runs for a few seconds and quits. Also gauges are not working even during the few seconds when it runs. Any ideas ????


Replace the battery if it is at least 4 years old. The computers will not power up if it does not have suficent voltage. put a new battery in it and check the charging system.

Jul 08, 2009 | 1996 Jeep Grand Cherokee

2 Answers

My 2000 Grand Jeep Cherokee cuts off while i'm driving and it gives no kind of sign when it cuts off....


thanks for more info replace the crank sensor it is breaking down when hot once it cools off it will work again .when they go bad the heat from the engine will break down the sensor

Feb 22, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Jeep garnd cherokee laredo 1995 model


check that the wiring to the amp underneath the right hand side back seat have not been disturbed

Nov 09, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
2001 Jeep Grand Cherokee Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...