Question about 1999 Chevrolet Blazer

1 Answer

99 blazer driver brake light only works when passenger turn signal is on?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

Sounds like the turn signal switch is bad.

Posted on May 30, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

ELECTRICAL PROBLEM


take it to a body shop

Nov 27, 2013 | 2000 Dodge Stratus

1 Answer

I have a 1992 GMC Yukon 4x4 blazer just had it in the shop when it came out the lights are all messed up. headlights work high and low. driver side turn signal dont work , passenger side turn signal don't...


If those lights all worked properly before the shop "fixed" it, take it back to the shop and ask them to make it right. If they are reputable, they will correct the problem(s). If not, think Small Claims Court.

Oct 08, 2013 | GMC Cars & Trucks

1 Answer

GMC Envoy 1999 -Brake lights not working (sort of).


bad earth on the bulb holder or the wiring, usually a good clean should sort it out.

Jul 19, 2017 | 1999 GMC Envoy

1 Answer

I have 1999 Blazer with brake light out on driver side only. All other lights work. Replaced bulbs but nothing changed. Swapped the working lights from the other (right side) with the driver side but...


THE BRAKE LIGHTS DO GO THROUGH THE TURN SIGNAL SWITCH. TO TEST, REMOVE THE PLASTIC COVER AROUND THE THE COLUMN, UNDER THE STEERING WHEEL. THE TURN SIGNAL SWITCH MUST BE IN THE OFF POSITION. YOU WILL NEED TO EXPOSE THE WIRES UNDER THE STEERING WHEEL. DO NOT DISTURB THE WIRES IN THE YELLOW JACKET. THEY ARE AIRBAG WIRES. YELLOW PLUGS YELLOW JACKETED WIRES ARE AIRBAG.THE WIRE IN QUESTION HERE IS YELLOW BUT IT IS NOT IN A YELLOW JACKET, [ SLEEVE ]. NOW, PUSH ON THE BRAKE PEDAL. THE YELLOW WIRE IS LEFT REAR TURN & BRAKE WIRE, DARK GREEN IS RIGHT REAR TURN & BRAKE WIRE. BRAKE PEDAL DEPRESSED, IF BOTH OF THOSE WIRES HAVE POWER, ALL OF THAT IS OK. IF THE YELLOW WIRE HAS NO POWER TURN SIGNAL SWITCH IS BAD

Jan 16, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

I have a 1997 chevy blazer the hazards work fine but the turn signal is not working I checked the fuse in the fuse panel. what else could it be


Replace the Turn Signal Flasher Relay. It has 2 relays. One for the Hazard lights and one for the Turn Signals. The Turn Signal Flasher Relay is located Front seating area, driver side, passenger side of steering column, under dash, mounted near cigarette lighter. Optional mounting location is under dash, on driver side of steering column. (Curtorsey Auto Zone)

Dec 15, 2009 | 1997 Chevrolet Blazer

2 Answers

Tail lights work on both sides. turn signal and


Sounds like you need to replace the drivers brake/tail light.

Dec 14, 2009 | 1998 GMC Sierra

2 Answers

No brake lights on 2001 chevy blazer LT 2wd


Check your wires, the smoke could mean an electrical fire.

Jun 03, 2009 | 2001 Chevrolet Blazer

1 Answer

Lower brake lights dont work,third light does


Turn signal switch 95% of t he time. Try to work your hazards, if it stuck at all will also cause this.

Feb 10, 2009 | 1998 Chevrolet Blazer

2 Answers

1994 s10 blazer 4x4 passenger side rear turn signal / brake light


I would guess that you might have trailer wireing that could be a couse. not to mention have you checked the ground?

Jan 09, 2009 | 1994 Chevrolet S-10 Blazer

3 Answers

No turn signals or brake lights on left and right but brake light on top


I agree. My brake light dont work. Only the third brake light does. The running lights work but when i apply the brakes the rear tails dont light up.
I currently have this issue along with the signals dont work unless I bang the top of the steering colum. The hazard switch doesnt work either. If the signals dont work it makes this very quick clicking sound on the passenger side. I checked the fuses and they are good. The bulbs still work. The brake switch works cause the third brake light goes on. And seeing as I am having a problem with signals.....GM says I have to replace the switch in the steerg colume. Its a little box about the size of a cigarette pack. If you take apart the panels off ( right behind the steering wheel, where the hazard switch is) ...that is where it is located. Its plugged into the signal lever. Hope this helpa....Good luck everyone with this issue.

Oct 17, 2008 | 2001 Chevrolet Blazer

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...