Question about 2003 Kia Spectra

1 Answer

I was changing front passenger side tire when lug nuts snapped bolt off. How do I change lug bolts out to new one. Plan to change all for bolts and lug nuts for this tire.

Posted by on

  • Anonymous Mar 23, 2014

    Lug nut torque

  • Anonymous Mar 23, 2014

    Lug nut torque

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,074 Answers

Take tire off, take brake caliper off, remove rotor, take nut and bearing off, then hammer out old studs and hammer in new ones. Tim

Posted on May 29, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change rear ball joints on 2002 dodge stratus


Instructions
  1. Remove the Upper Control Arm
    • 1Disconnect the ground battery cable using a wrench.
    • Loosen the front wheel lugs located on the same side of the upper ball joint you need to replace. Use a lug wrench.
    • Raise that same front wheel off the ground using a floor jack and support the vehicle on a jack stand.
    • Finish removing the tire.
    • Take the cotter pin off the upper ball joint stud holding the steering knuckle arm. Use a pair of nose pliers.
    • Remove the castle nut from the upper ball joint stud using a wrench or ratchet, ratchet extension and deep socket.
    • Loosen the two bolts securing the back of the upper control arm to the mounting bracket. Use a wrench to hold the bolt head as you loosen the retaining nut with a ratchet and socket.
    • Pull the control-arm ball joint off the steering knuckle arm. You may need to use a Pitman arm puller to free the ball joint.
    • Finish removing the two bolts from the back of the upper control arm and lift the upper control arm off the vehicle.
    Install the New Upper Control Arm
    • Set the new upper control arm in place and install the two bolts and retaining nuts to secure the back of the upper control arm to the mounting bracket. Remember the bolt heads should point inward toward the shock absorber with the retaining nuts on the outside of the mounting bracket. Do not tighten the bolts yet.
    • 11Insert the control-arm ball joint on the steering knuckle arm and start the castle nut with your hand over the ball joint stud. Do not tighten the nut yet.
    • Tighten the two bolts on the mounting bracket to 67-foot lbs. (91 Nm) using a torque wrench. Hold the bolts with a backup wrench as you tighten the retaining nuts with the torque wrench.
    • Tighten the ball-joint castle nut to 45-foot lbs. (61 Nm) using the torque wrench, ratchet extension and deep socket.
    • Install a new cotter pin through the joint-ball stud hole using the nose pliers. If necessary, tighten the castle nut just a few degrees to clear the stud hole through one of the castle nut slots.
    • Mount the tire on the wheel assembly and install the wheel lugs using the lug wrench.
    • Lower the vehicle and finish tightening the wheel lugs.

May 31, 2012 | Dodge Stratus Cars & Trucks

1 Answer

CV axle shaft replacement


Instructions
1.Set the vehicle transmission in "Park" and engage the emergency brake before attempting to remove the front right axle. Place wood blocks behind the rear wheels to prevent the vehicle from rolling and loosen the lug nuts one complete turn on the right front wheel with a tire tool.

2. .Lift the front passenger side of the vehicle with a floor jack and slide a jack stand under the vehicle frame near the wheel. Lower the floor jack so the vehicle is sitting on the jack stand and move the floor jack out of the way.

3. Remove the lug nuts with the tire tool and set the front passenger wheel out of the way. Take the cap off the end of the axle with a standard screwdriver and remove the cotter pin from the axle with a pair of pliers.

  • 4. Slide the crown washer off the axle and loosen the axle nut with a crescent wrench. Unfasten the top and bottom bolts that secure the brake caliper to the rotor with a socket wrench and slide the bolts out of the caliper.
  • 5. Lift the brake caliper off the rotor and remove the brake pads from the caliper. Suspend the brake caliper from the vehicle frame with a wire hanger and take the rotor off the axle.
  • 6. Unfasten the thru-bolt on the vertical sway bar with a socket wrench and remove the bolt from the sway bar. Take the channel bolt out from between the sway bar and lower A-arm that the thru-bolt ran through, and loosen the bolts that secure the front right axle to the center flange with a socket wrench and breaker bar. You may need to loosen the bolts with the breaker bar before removing them with the socket wrench.
  • 7. Slide the front right axle off the center flange and let it rest on the A-arm. Lift the front passenger side up with the floor jack to get enough room between the steering knuckle and A-arm and slide the axle out of the vehicle.
    Install in reverse order.
  • Mar 23, 2012 | 2006 Mazda 3

    1 Answer

    How to change front brake pads on 2006 town and country


    Loosen tire lug nuts. Jack up the car and remove lug nuts and tire. Remove two bolts holding the caliper in place. Remove the the two bolts holding pads in place. Hang caliper with a wire from wheel so brake line is not stressed. Mount new calipers in correctly and tigthen pad bolts. Put caliper on and tighten caliper bolts. Replace tire and lugs nuts. Jack car down and tigheten lug nuts.

    Aug 17, 2010 | 2006 Chrysler Town & Country

    1 Answer

    Broken lug nuts


    Get how ever many wheel bolt's you need and one more lug nut, you will used that one to press in new wheel bolt, any parts place will have these parts, remove tire with hammer hit broken stud till it come's out through the back side, put new wheel bolt and with extra lug nut press in bolt, hope this was very helpful.

    May 20, 2010 | 2004 Ford F150

    1 Answer

    My front driver side in the middle of my rim the bolt has snapped off an i need to know what its called an how to fix it


    lug stud or lug bolt. you need to get the rotor off and lay it flat bolts up on a piece of wood tthen hit the broken one with a hammer should pop out back then push the new one in from the back when you put the tire back on the lug nut with set it in place

    Oct 24, 2009 | 1996 Plymouth Breeze

    4 Answers

    Releasing 2005 Toyota Sienna spare tire


    On my 2004 toyota,,,directly behind the passenger side front seat (have to push passenger seat all the way forward to see it, there is a small square flap in the carpet,,,lift that up and underneath is a big bolt which you turn counterclock wise with your spare tire lug wrench and the tire will lower to the ground. thats about it. good luck

    Aug 29, 2009 | 2004 Toyota Sienna

    1 Answer

    Rear tire lug bolts


    You have to remove the tire/wheel assy. remove the brake drum, you will see the spindle with the bolts there. punch out the broken bolts install new buy pushing thru the hole.Find some regular nuts that will fit over the stud, put your new nuts on and tighten up till flush in back.

    Jun 07, 2009 | 2003 Chevrolet Cavalier

    2 Answers

    1998 Corolla Wheel Bolt


    lugnuts and wheel studs
    you will have to pull the barke drum off and knock the studs out and should be able to get new ones in and use a nut and spacer to pull the new studs tight

    Aug 26, 2008 | 1998 Toyota Corolla

    Not finding what you are looking for?
    2003 Kia Spectra Logo

    323 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Kia Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Kia Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...