Question about 1985 Nissan Pickup

2 Answers

TRYING TO REMOVE REAR BRAKEDRUM ON 85NISSAN PICKUP //?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 82 Answers

Normley only held on by two screws.some times you have to slacken off the breake adjuster.and handbreak cable,

Posted on May 29, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 49 Answers

I use a 3lb hammer to tap the lip from the back of the drum after I have hit the face of the drum being careful to not hit any of the wheel studs. You can also put a little penetrating oil on the drum where it allows the hub to come through and a few drops around where the wheel studs come through the drum so that it helps with softening the corrosion. Some drum assemblies will also have a pilot screw that will be used to hold the drum in place until the wheel is put back on so check for that as well.

Posted on May 29, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove a rear end from a 1993 chevy z71 4x4 1/2 ton pickup?


Fairly simple process( but not always easy,Just warning you in advance) 1. Disconnect rubber brake line from top of axle.Plug appropriately to prevent fluid loss. 2. Disconnect e-brake cables. (beside the frame on driver's side) 3. Remove shocks ( or just diconnect at either end) 4. disconnect driveshaft at axle and leave in trans (if possible) to prevent fluid loss. 5 Axle can now be removed by either removing the bolts at each end of the springs or by removing the u-bolts attaching the axle to the springs

Sep 11, 2014 | Chevrolet Cars & Trucks

1 Answer

How do I remove a rear end from a 1993 chevy z71 pickup 1/2 ton 4x4?


1 Disconnect hydraulic brake line. 2. Disconect e-brake cables beside the frame. 3. Disconnect driveshaft. 4. Remove shocks 5. Disconnect ABS wiring (if equipped) 6. Remove bots at each end of springs or remove u-bolts that are holding the axle to the springs

Sep 11, 2014 | Cars & Trucks

1 Answer

Can't get the rear brakedrum off


emergency brakes not engaged, right ? Look for small access hole on rear plate, theres a little toothed wheel there you can turn down with a small screwdriver to adjust shoes, keep turning it till pressure off shoes

Apr 08, 2014 | 2002 Jeep Liberty

1 Answer

Trying to remove the stick shift from a 1992 toyota pickup to replace the clutch


REMOVE TRANSMISSION SHIFT LEVER FROM INSIDE OF VEHICLE
    • Remove the four screws and remove the shift lever boot retainer.
    • Pull up the shift lever boot.
    • Cover the shift lever cap with cloth.
    • Then, pressing down on the shift lever cap, rotate it counterclockwise to remove.
    • Remove the shift lever.
62409690

Jan 22, 2011 | 1992 Toyota Pickup

1 Answer

Unable to remove rear brakedrum 2001 focus


the drum and bearing are one unit. You'll need to remove the center cap and the axle nut. The drum will then come off with no problem.

Make sure you tighten the axle nut to the proper spec after you put the drum back on, otherwise you'll ruin the bearing

Sep 24, 2010 | Ford Focus Cars & Trucks

1 Answer

How do i get a stuck brakedrum off i have tried prying it rubber mallet still wont budge!


There is a brake adjustment tool that you can use to back the brake off, or continue to beat it with a 5lb steel hammer

Jul 23, 2009 | Pontiac Sunbird Cars & Trucks

1 Answer

Rear axle bearings


There are 4 bolts for each rear axle. They are located behind the rear brake drums. Remove e-brake cable from rear drum and take off brake line.(carefully). I recomend draining and changing your rear differential fluid too, because if the fluid by run out of axle housing. also you should replace the seals for the axles of if you are changing the bearings. When you are done don't forget to bleed your brakes, and hooking up e-brake cable. I hope this answers your question.

Jan 28, 2009 | 1986 Toyota Pickup 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...