Question about Dodge Grand Caravan

1 Answer

Replaced the belt didnt get it lined back up right and i need a diagram of the marks and pullys thanks

Posted by on

  • Jeremy W.
    Jeremy W. May 29, 2011

    year, make, model, engine size?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,072 Answers

Since you did not give any information to find the model, etc here is the website that may help Tim:

http://www.2carpros.com/diagrams/dodge

Posted on May 29, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reroute the drivibg belt or fan belt


Hi,just inline the crankshaft to the top dead centre marks,then check that the camshaft marks line up,if they dont line up then turn the crankshaft pully again untill the camshaft marks line up,slacken the timeing belt pully adjuster take belt off and replace with new one,tighten the pully adjuster back up,now put a spanner on the crakshaft pully and turn clockwise untill the top dead centre marks and the camshaft marks inline if they dont then slacken the ajusting pully inline marks again and try again,if marks do inline ok then you are ready to start the car.
hope this helps good luck.

Feb 25, 2015 | Cars & Trucks

1 Answer

1990 ford ranger 2.3 timing belt pully diagram


Set the crank to TDC using the timing marks, Then look for an arrow or a mark on the cam shaft pully and another mark on the block. Line those up. Put the belt on, make sure the marks did not move.

Feb 12, 2013 | Cars & Trucks

1 Answer

1990 ford ranger 2.3 timing belt pully diagram


Set the crank to TDC using the timing marks, look for a mark on the cam pulley and a mark on the head, line those marks up and put on the belt

Feb 12, 2013 | Cars & Trucks

1 Answer

How do i time my Golf 1 correctly? it consumes a lot


its tricky enough if your not sure what your doing but ill run you through it. 1. remove top rocker cover and timing belt cover. 2 make up the position of the pully on the cam shaft at the top and the drive shaft at the bottom, this marks are you fail safe incase you cant time the engine. 3 remove the timing belt and pully tentioner, note if your going this far you are as well to replace the timing belt,tentioner and water pump. 4 On the cam shaft at the top if you force them to turn you will see a small indicator mark on the shaft this mark has to line up with the other indicator mark on the housing between the cam shaft and the cam shaft pully, once they line up your top end is timed, mark up the pully incase it moves. 5 on the drive shaft pully there is also markings that have to line up but you can also feel the position of the pully as you turn it, you will feel the piston been forced up and it is timed at top dead centre on cylinder one, which means the the piston has to be at the top just before the point of returning back down, using your feeling as a guide and the markings lined up you will have timing. also mark up this pully, your new marking should be very very close to the fail safe markings you put on at the start. when you have your marking replace the timing belt with the longest distance between pully contact going on first, try not disturb your timing or your hard work will have been for nothing, make sure the tentioner on the belt is tight but not to tight to the point where you ll stretch the belt or snap it, put everything back as you found it and crank the engine, job done, best of luck. hope this helps( rate me on my answer thanks )

Aug 27, 2010 | 2000 Volkswagen Golf

1 Answer

Back fires


you have all 7 marks lined up? there are the top two pullys that need to be lined with the top marks on the rear timing covers, and then there are two marks on the bottom of those pullys that need to be lined with the marks on the two bottom pullys, as well as the two side marks on the bottom pullys that need lined on the belt, and then the mark on the crak pully that needs lined up with the mark on the oil pump?

Mar 07, 2010 | 2007 Subaru Impreza WRX STI Limited Sedan

1 Answer

Kia Carens Timing marks


hi..as you look at the engine, the left camshaft pully should have the I alligned at the top with the mark on the cover, as the camshaft pully to the right with the E should also be at the top aligned with the mark on the cover, and the crank should have its mark also at the top ( the cut out behind the pully ) should line up with the mark on the casing i have a diagram if you want it...hope this helps

Feb 12, 2010 | 2000 Kia Sportage

1 Answer

Diagram of changing a 2000 model nissan xterra timing belt


I am assuming you have the 3.3 litter v-6?cf56ba7.gifI just did my own so I can offer you a few words of personal advice. Make sure, before you remove the crank shaft pulley, that the engine is at TDC. There is a pointer on the lower timing cover that should line up with the mark that is furthest to the left on the crank pulley (looking at it from the front of the truck). If you are replacing the timing belt for maintenance, not failure, make several marks on the cam pullies to the rear of the timing cover with a paint pen before removing the old belt and make sure that everything stays aligned to those marks upon reassembly. If this method is not an option, use the timing dimples on the back of the upper timing cover only as reference points for the cam pulleis (this is where I ran in to trouble). What is most important is that there are exactly 40 teeth on the belt between the marks on the cam pullies and 43 teeth between the right cam pully mark (right cam as you look at the engine from the front of the truck) and the mark on the crank pully. I used a Goodyear Belt that actually had marks that indicated the 40 and 43 tooth increments. Make sure you have the belt on the right directon, arrows to the front of the truck. Again it is very important that the crank pully remain at TDC (top dead center) during the entire process. Good luck, hope you get it the first time and not the second like me!!

Jan 27, 2010 | 2000 Nissan Xterra

3 Answers

Timing mark


Cam has a "V". Crank has a keyway. Both should be directly on top of the pullys toward the top of the engine. This is an interference engine. Do not force. After replacing the timing belt, turn the crank by ratchet (clockwise) two complete turns to assure. Should feel some resistence but not more than you can easily overcome. If it stops dead and you KNOW it's "just not right" you are 180 out and need to start over.

Oct 27, 2008 | 1991 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...