Question about 1995 Mazda MX-3

1 Answer

Last week my car would not start i check all the plugs and 1 and 4 where wet and 2 and 3 where dry i clean them all put back together and started the first time and now its doing the same wont start

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 131 Answers

Locate the 1-4 cylinders coil pack. Have that coil pack checked at the parts store. If there's only one coil pack for all four cylinders, then have the whole coil pack tested. If the coil pack checks out OK, then have the ignition module tested and replace if necessary. If you don't have a parts store that can test them for you, then give me a response and I can tell you how to check them using a test light and an ohm meter. I hope this information has been helpful and thank you for using Fixya.com.

Posted on May 29, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1994 E 350 want start after it rains is there something getting wet that want let it start


Yep, there is. And your not going to like it. The easy fix, on the drivers side, standing in front of the van, on the right side of the brake booster. There are three plugs. They bolt on. Remove them, clean them with battery terminal cleaner, blow them off, add dielectric silicone. Lots of it. Put them back together. This should fix your problem. This may last 6 months to a year. Now the pain in the but fix. Pull the plugs, cut one wire on each plug, inside and out, at a time and hard wire/solder them together. Everyone that I have done an easy fix to, had to be hard wired. I don't do easy fixes any more.

Jan 03, 2015 | Cars & Trucks

1 Answer

Bad fuel injection symptoms


P0202 is something wrong with cylinder 2 injector circuit malfunction. I would start with checking the wires on the number 2 cylinder making sure the connector is clean and plugged in. Also check and see if the spark plug is wet if it is dry off plug and put back in because it was not firing.

Mar 31, 2014 | 2003 Dodge Neon

1 Answer

Will not start


Year make and model, and are the spark plugs wet or dry ?

Feb 04, 2014 | Cars & Trucks

1 Answer

98 dodge intrepid/ 2.7 liter, cranks but will not start. Even with using starting fluid. Plugs are wet


take out the plugs take them inside let them dry out for 6 to 15 hours
before replaceing them crank the starter once or twice to dry out the cylinders put the plugs back in start it and away you go

Dec 25, 2011 | Cars & Trucks

1 Answer

Engine turns over but wont start? it has spark! and fuel!


Pull out # 1 spark plug and put back into plug wire, rest on motor block so that end of electrode is against metal. turn motor over and have a finger or compression gauge in # 1 cylinder, check to see if spark occur at same time as compression (compression will blow air past finger or raise gauge). When you say it has fuel do you mean gas tank has fuel? Are you sure fuel is getting to the cylinders? are plugs wet with fuel? Does it turn over but kinda thumps or backfire (Caugh)? Check the spark and compression first. if they don't happen at same time, the timing skipped or belt broke. if all is good pull plugs and inspect, could be flooded (WET) from fuel. either replace or spray with starting fluid and compressed air to dry them. spray starting fluid into air intake if starts then stalls, try again, if same thing happens then you have a fuel problem. try these suggestions first 1/2 hr time table, hopefully sucess, if not it sure indicates fuel.

Jan 10, 2011 | 1995 Subaru Legacy

1 Answer

My 1994 nissan pickup cranks but will not start


Need to check for fuel. Easy way to do this is wipe one of the plugs clean and dry and put back in without wire attched. Crank truck as if you were trying to start it. Pull plug out and check to see if it is wet. Should smell like gasoline. If so, recommend you replace the plugs, wires, distributor cap and rotor. If not, you have a fuel problem.

May 17, 2010 | 1994 Nissan Pickup

1 Answer

Ignition turns over but car will not start...


sorry to hear your vehicle is down. check the fuel filter if so equipped, or could be fuel pump.
hope this helps. have a good day

Jan 29, 2010 | 1992 Isuzu Rodeo

1 Answer

Car is not wanting to accelerate


Did you check the catylactic convert may be plugged

Dec 03, 2008 | 2001 Chevrolet Corvette

Not finding what you are looking for?
1995 Mazda MX-3 Logo

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...