Question about 2008 Chevrolet Malibu Classic

1 Answer

2004 chevy classic power windows front passenger

2004 chevy classic power windows front passenger window will go down but not up. rear passenger wil not work at all.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 131 Answers

It sounds like the front window has a bad window switch. Removing the switch panel is usually not that difficult. Look for a pry slot usually located at the back of the panel. Insert a small flat blade screwdriver and pry up on the panel. The switch panel should come out of the door panel. Next, locate the wiring harness for that switch. The switch panel can be tested as follows :
1. Connect a test light to one side of the harness and operate the window.
2. Do the same thing for the other side of the harness.
If the light comes on in one direction but not in the other, then the most likely cause is a faulty switch panel. Perform the same procedure for the rear window. If it lights in both directions, then the most likely cause is a bad window motor. If that is what it appears to be, then I can tell you how to test the window motor before replacing. Just give me a response back if you need to. I hope this information has been helpful and thank you for using Fixya.com.

Posted on May 29, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the right front door panel on a 2004 buick le saber


Did you test it or are you guessing just because it won't open or close ? How To Install Remove Front Door Panel Buick Lesabre 00 05 1AAuto com both right an left are the same .
Power Windows System Components
The following components are used to control the power windows:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Front Door Module (PDM)


?€¢
LH Rear Door Module (LRDM)


?€¢
RH Rear Door Module (RRDM)


?€¢
Driver Door Switch Assembly (DDSA)


?€¢
RH Front Power Window Switch


?€¢
LH Rear Power Window Switch


?€¢
RH Rear Power Window Switch


?€¢
LH Front Power Window Motor


?€¢
RH Front Power Window Motor


?€¢
LH Rear Power Window Motor


?€¢
RH Rear Power Window Motor


?€¢
Class 2 serial data circuit


?€¢
Power door serial data circuit


?€¢
PWR WDO 30 Amp Circuit Breaker


?€¢
DRVMDL Fuse (10 amp)


Driver Door Switch Assembly and Driver Door Module logic, Driver Door Module internal driver operation


?€¢
PASS MDL Fuse (10 amp)


Front Passenger Door Module logic and internal driver operation


?€¢
RRDR MDL Fuse (10 amp)


Left Rear Door Module and Right Rear Door Module logic and internal driver operation


Do you know about computer controlled power windows ?
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.

Oct 30, 2016 | Buick Cars & Trucks

2 Answers

Driver door will not work lock or windows


They hooked into wiring they shouldn't have >
Power Window System Components
The power window system consists of the following components:
?€¢
Driver door module (DDM)


?€¢
Passenger door module (PDM)


?€¢
Body control module (BCM)


?€¢
LR power window switch


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left rear window)


?€¢
RT DOOR CB 25A (System power for right rear window)

Power Window System Controls
The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

Jan 10, 2016 | 2004 GMC Envoy

1 Answer

My power seats and only the power windows on right side quit working on my 2007 silverado classic lt1500 I replaced the circuit breakers already and it did not fix the problem


Does you truck have Memory Seats ? There are 2 options of power seat systems available in full size trucks. The first is 6 way driver and passenger power seats without memory. The second is an 8-way driver seat plus 4-way lumbar with memory, heat and optional cool function.
If you replaced the circuit breaker , did you check for B+ voltage at the switch ? If you have memory seats there is a control module that is in the mix.
For the power windows same thing here ,the BCM - body control module is involved .A factory Tech 2 scan tool is still the best tool to use ,checking data parameters .
The switch for the front passenger power window has 2 positions UP and DOWN, and it's position is a direct input into the PDS. Upon receiving a request for power window operation (switch activation), the PDS supplies voltage to the power window motor right front up or down circuit and grounds the opposite and the power window motor runs to drive the window UP or DOWN.
The front passenger power window can also be operated from the driver master control. The front passenger window switch on the driver master control has 2 positions UP and DOWN and it's position is a direct input into the DDS. Upon receiving a request for front passenger power window operation, the DDS transmits a GMLAN message indicating the changed switch position. When the PDS receives this message, the PDS supplies voltage to the power window motor right front up or down circuit and grounds the opposite and the power window motor runs to move the window UP or DOWN.
GMLAN - is a data bus communication network that vehicle modules talk together on.
Rear Passenger Power Window Operation (RPO A31/AN3/DL3)
The body control module (BCM) monitors the window UP/DOWN command from the DDS. When the rear window UP or DOWN command is received, the BCM sends a signal to the appropriate rear window switch. The rear window switches continuously monitor the up and down signal circuits, if no function is being commanded, the signal voltage is at approximately B+ voltage. If the UP or DOWN function is commanded, the BCM signal voltage drops approximately 5 volts and the appropriate rear window switch will then command the window in the UP or DOWN direction.
Your best bet would be to take your truck to a GM dealer !
Your best bet

If

Nov 04, 2015 | Cars & Trucks

2 Answers

Problem with power windows


most likely the window regulators. these make sure the window is pulled and pushed evenly. if this is faulty or damaged then the window will be pulled at an angle. new regulator is probably the easiest option

May 12, 2012 | 1996 Chevrolet Caprice Classic

1 Answer

2004 deville passenger front and rear power windows


hello there:
you may have to disassemble the door panel and check to see if the cable going to the actuator has come off if the cable is there and mounting looks OK you may need to replace the actuator its a simple procedure to do and it's just as expensive to replace the motor and actuator together at the same time the reason for this is to resolve future problems.... hope this helps thanks

May 30, 2010 | 2004 Cadillac Deville

2 Answers

The passenger rear window won't roll up or down from the drivers controle it clicks in the passenger front door. it will roll down in the passenger rear door but not up. the window modulator rolls up and...


I have the exact same problem on a Jeep Grand Cherokee 2004. The rear passenger window rolls down only from the rear passenger window and won't go up or down from the front. It has to be in the wiring because the problem was intermittent initially and a new window motor does the exact same thing. If you figured it out or have the wiring diagram please let me know.

Apr 22, 2010 | 2004 Jeep Grand Cherokee

3 Answers

PASSENGER SIDE FRONT AND REAR POWER WINDOWS NOT WORKING


then it might be the motor to that window or a bad switch for that window.

Jul 12, 2009 | 2003 Chevrolet Silverado 2500HD

1 Answer

Passenger power window powers down not up


If you can do it, run a jumper from the drivers door to the passenger door. Unplug both motors. try to run the passengers door off the drivers switch to rule out the motor. I don't think it is because the motor is dc. But this is the common point. Please mark this as helpful or fixya. Shuold you have anymore problems, I used to be a mobile mechanic electircian. Looking forward to hearing from you.

Dec 31, 2008 | 2004 Chevrolet Venture Passanger

1 Answer

Only rear power window wont work, front are fine.


the window motors are most likely no good

Aug 15, 2008 | 2004 Chevrolet Colorado

Not finding what you are looking for?
2008 Chevrolet Malibu Classic Logo

347 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...