Question about Chevrolet Camaro

1 Answer

Dimmer switch on my 1984 camaro needs replacing. Can I do this in place ? or do I have to remove the colum. Cheers, Shrapnel

Posted by on

  • Anonymous Mar 29, 2014

    how do i remove the cover on the colum

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 277 Answers

You should just have to remove the steering wheel.

Posted on May 29, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlights will work on bright but not on dim. Tail lights will work regardless if one has it on bright or dim. Daytime driving lights work. The problems must be in the light switch on the left side of...


you could have a dimmer switch problem that may need an adjustment or replacement.do you hear the switch click when you try to change from high to low,if not than these could be the problem.the switch is located on the top of the steering colume and the base of the colume under the dash.if you work the dimmer switch on the colume and put your hand on the colume under the dash you should be able to feel the rod that pushes on the switch.follow the rod down and it will go to the dimmer switch.there are 2 5/16 bolts that hold it in place that if you loosen them and push the switch up towards the steering wheel it will move it so the rod won`t have to move as far to change from low to high.if this is not the problem and you don`t hear a click then its usually a switch replacement.

Sep 18, 2011 | 1994 Chevrolet Cavalier

2 Answers

How to fix the dimmer switch on a 1992 Buick LeSaber does NOT Click on when I pull back on the same handle for wipers, cruse control & ect. Need a quick fix it will not pass Texas inspection and...


the dimmer switch is located on the steering colum about half way down . It is kind of hard to see .. there is a rod that runs from the turn singal handle down to the dimmer switch . it could be off or missadjusted . will need to check it might need a flash light to see it . the dimmer switch adjust with two little bolts i think they are 5/16 so they will need to be loosen to adjust the switch and rod or they will need to be removed to relplace the switch . i think the switch should be under 25 dollars if you need to replace it and should beable to be found at any local parts store

Mar 04, 2011 | 1992 Buick LeSabre

2 Answers

Need a fuse box diagram for 84 camaro z28


you might find the fuse diagram on the inside of the fuse box cover under the hood....hope this helps....cheers

Aug 14, 2010 | 1984 Chevrolet Camaro

1 Answer

I have a 1984 Chevy 3/4 ton, the dimmer switch on the colum has stopped working, I don't think it is the harness, the lever arm has something missing. were can I find a diagram of the steering wheel colum....


Try this website to download a free manual

Trouble trees are listed for all makes in the manuals for dianogstics



http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

May 01, 2010 | 1984 Chevrolet C2500

1 Answer

Need to know how to instal the horn contact and spring into a 1984 camaro steering colum


First you need toremove the steering wheel. You will also need a lock ring removal tool. This tool will help you remove the circlip from behind plastic cover. Dont lose this clip.After you have removed the lock plate then the horn ring should be visible and you can replace it.

Apr 27, 2010 | 1984 Chevrolet Camaro

2 Answers

I have a 84 Chevy Celebrity stationwagon and the turn signal quit flashing but still comes on, Is there more than one relay under the dash for this. I already replaced the one I found and no change.


it could be the flashing signal switch, the electrical wires in the stearing colum sometime brake, try that. hope it helps you. in order to remove it you need to take cover of stearing colum and usually one plug and two bolts hold it in place. good luck

Mar 18, 2010 | 1984 Chevrolet Celebrity

1 Answer

Need to take out


Disconnect the battery. Remove the steering wheel. Remove turn signal switch,Remove the buzzer switch with needle nose pliers. Then insert the key(make sure it is not in place beforehand) and place in lock position. remove lock cylinder retaining torx screw. Then with key in place, pull out the assembly straight out.Disconnect the electrical connector from the bulkhead connectorand remove retaining clip. attach some wire to the connector to help with installation and pull harness through column. Installation is reverse.

Jul 06, 2009 | 1984 Chevrolet Camaro

1 Answer

Ignition removal process for 1984 chevy 1/2 ton


This Outlines Removal Of Both LOCK CYLINDER<< Mechanical)) And The Ignition SWITCH ITSELF<< ELECTRICAL))
  1. Remove steering wheel as outlined previously.
  2. Remove turn signal switch as outlined in ``Turn Signal Switch, Replace'' procedure.
  3. Place ignition switch in ``Run'' position, then remove lock cylinder retaining screw and lock cylinder.
  4. To install, rotate lock cylinder to stop, while holding housing as shown, Fig. 6. Align cylinder key with keyway in housing, then push lock cylinder assembly into housing until fully seated.
  5. Install lock cylinder retaining screw. Torque screw to 40 inch lbs. for standard columns, or 22 inch lbs. for adjustable columns.
  6. Install buzzer switch, turn signal switch and steering wheel


CABALLERO, EL CAMINO, C, K, R, V & 1986---87 G MODELS
The ignition switch is mounted on top of the mast jacket inside the brake pedal support and is actuated by a rod and rack assembly.
  1. Disconnect battery ground cable.
  2. Disconnect and lower steering column. On some models, it may be necessary to remove the upper column mounting bracket if it hinders servicing of switch. Use extreme care when lowering steering column to prevent damage to column assembly. Only lower steering column a sufficient distance to perform ignition switch service.
  3. On Caballero and El Camino, rotate ignition lock to ``Off'' unlocked position.
  4. On C, K, R and V models, rotate ignition lock to ``Off'' locked position.
  5. If lock cylinder has been removed, pull switch actuator rod up to stop, then pushrod down to second (Caballero or El Camino) or first (C, K, R and V models) detent as shown, Fig. 7.
  6. Remove column mounted dimmer switch, if equipped, then remove switch retaining screws and switch.
  7. Reverse procedure to install, noting the following:
    1. Place gear shift lever in neutral.
    2. Place lock cylinder and switch in positions noted in steps 3 and 4.
    3. Fit actuator rod into hole in switch slider and secure switch with retaining screws, ensuring switch does not move out of detent.
    4. Install and adjust dimmer switch, if equipped, as outlined in ``Column Mounted Dimmer Switch, Replace'' procedure.
    5. Torque retaining screws to 35 inch lbs., then check switch operation.

Feb 21, 2009 | 1984 Chevrolet K1500

1 Answer

I need to change the ignition switch in my 1986 chevrolet pickup truck. How do I remove and install this part? Thanx.


the switch is located on the seering colum under the dash step 1 is to remove the access cover on the lower dash board. after disconecting the battery. step 2 is to carefully lower the steering colum 2 nuts to dash frame work (use care if automatic not to pullo the shift indicator wire or disconectit from the steering coulmn befor lowering. at this piont u should be able to feel and see the switch on the left upper side of the column it is held in place by 2 smal bolts which may also hold the dimmer for your headlighs. rommve the bolts disconect the wires and reoplace

Feb 20, 2009 | 1990 Chevrolet K1500

1 Answer

1984 Camaro Z28 Wiper switch wont work properly


hello I will take a picture of the Diagram and send it to yea I have a 86 Iroc z28 So i have a Haynes manual for yours as well for most of the f body's are universal. I need a Email or a way to send you the file?

Dec 01, 2008 | 1984 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...