Question about 2000 Ford Mustang

1 Answer

MI have a 2000 ford mustang and need to check or fill the transmission fluid where do I find this? It is a manual transmission.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 158 Answers

Naughtyon904, Most manual transmissions have a drain plug (on the botttom) and a fill plug (on the side ) of the transmissions. You need to raise the vehicle with ramps and visually check the transmission. Find the fill plug and remove it. With your finger check the level of the oil. It should be at the top of the fill hole. Also, check with your local dealer to find out exactly what is in the transmission as it is usually gear oil and not transmission fluid that is used. They can tell you the exact weight of the oil to be used and if there are any additives. Good luck with this.

Posted on May 29, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust bands in 2000 mustang automatic transmission


must have jack stands so vehicle dont fall on you--the fluid pan is removed carefully so no spillage-ajustment bolts are found in the hardware--chech w a repair manual for details

Jan 10, 2015 | 2000 Ford Mustang

1 Answer

How to check transmission fluid on 88 mustang 5.0


from:milton wright.your 1988 5.0 mustang with automatic trans.the dip stick should be under the hood,on the passenger side next to the fire wall.look down! check with the engine running,transmission in park!

Jul 16, 2012 | 1988 Ford Mustang

1 Answer

How to check transmission fluid level? with the engine idling or?


TRANSMISSION CANT BE TOO HOT AFTER DOING A LOT OF DRIVING.BEST TIME TO CHECK TRANSMISSION FLUID WHEN ENGINE COOL.TO CHECK FLUID LEVEL.CRANK ENGINE UP.LET IT IDLE UNTIL ENGINE AND TRANSMISSION GET WARM. WITH ENGINE IDLING.SHIFT TRANSMISSION FROM PARK TO LOW 1 GEAR. TWICE DO EACH GEARS AT ONE TIME. WITH TRANSMISSION BACK IN PARK.CHECK TRANSMISSION FLUID LEVEL ON DIP STICK SHOULD BE AT THE FULL MARK IF NOT ADD A PINT AT A TIME TO GET TRANSMISSION FLUID LEVEL CORRECT. DONT OVER FILL.

Aug 18, 2011 | 2002 Ford Mustang

1 Answer

How many quarts of transmission fluid goes in a 2000 ford explorer /


Hello there
abar_a.gif?v=72006
2000 FORD TRUCKS EXPLORER 5.0L 8-cyl Engine Code P

FILTERS
AMSOIL Ea Oil Filter.........EAO11
Wix Oil Filter.........51372
AMSOIL Ea Air Filter.........EAA122
Wix Air Filter.........46253
Wix Fuel Filter.......33595
Wix Trans Filter.....58955 [1]

[1] 4R70W

CAPACITIES
Engine, with filter..........5.0 quarts[1]
Cooling System, Initial Fill..........15.0 quarts
Automatic Transmission, Others Initial Fill..........3.9 quarts[2]
Automatic Transmission, 4R70W Initial Fill..........5.0 quarts[2]
Automatic Transmission, Total Fill
4R70W..........14.0 quarts
2wd ..........10.0 quarts
4wd ..........10.0 quarts
Manual Transmission, ..........5.5 pints
Differential, Rear..........5.7 pints[3]
Differential, Dana 35 Front..........3.6 pints[4]
Transfer Case,Full-Time 4WD..........2.7 pints

1. When refilling, remove dipstick to provide adequate venting and allow oil to flow into crankcase.
2. With ENG at operating temperature, shift through all gears. Check fluid level in PARK and add fluid as needed.
3. Fill to no more than 1/4 to 9/16" below fill plug hole.
4. Fill no higher than 9.5 mm or 3/8" below fill plug.


Aug 07, 2010 | 2006 Ford Explorer

1 Answer

How do i change the front seal on the automatic transmission of a 1996 ford mustang?


Your first step is to diconnect the battery. Then comes the hard part you must pull the transmission out of the car and put it on a bench or work table (for ease of working). After this you must remove the torque convertor and there is a seal ther and also a seal for the front pump. Ifyou replace both make sure everything is perfectly clean before installing any seals or they will leak again. Transmission fluid is very thin and will find gaps at seals due to dirt very easily. After seals are installed reinstall trans and fill with the proper fluid as per owners manual. Start car and leave it warm up while checking for leaks and recheck the fluid. If everything looks good road test and recheck. If still fine just keep an eye on it and drive away.

Sep 12, 2009 | 1996 Ford Mustang

1 Answer

Convertible top motor runs for a few seconds and quits. top goes uo about 6 inches but settles back when motor quits. how can i check to see if motor is still good or if needs replacing?


the motor just pumps hydraulic fluid into the lift pistons. If you are low on fluid, the motor can't create enough pressure to run the pistons. Check the fluid level.

1994 info

Section 01-17: Convertible 1994 Mustang. Workshop Manual
ADJUSTMENTS Fluid Level
  1. Remove rear seat. Refer to Section 01-10 .
  1. Carefully remove the rubber fill plug from the back and the reservoir and check the fluid level. The level should be at the bottom of the filler hole. If necessary, add Synthetic Mercon® Multi-Purpose Automatic transmission fluid E6AZ-19582-B or equivalent meeting Ford specification ESR-M2C163-A2. srb~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not overfill or the reservoir seal could be blown out.
  1. Replace fill plug with a new fill plug.
  1. Bleed system as outlined if necessary.

Jul 08, 2009 | 1965 Ford Mustang

2 Answers

Second gear grinds?????????????


There Should Be A Plug On The Side Of The Transmission. You'll See The Head Of A Bolt On The Side Toward Top, Or Middle. One On Very Bottom Is The Drain. Now Just Look For Another Similar Plug. Make Sure That Year And Model Doesn't Take Automatic Transmission Fluid. If It Doesn't Go Away. Time To Have Rebuilt. Syncro's Are Going. Good Luck

May 02, 2009 | 2000 Ford Mustang

2 Answers

What do i use for power steering fuid


you can change it but the fluid is about the same i was told if your power steering was low and you had none you can sub trans fluid

Apr 20, 2009 | 2000 Ford Mustang

1 Answer

Termactor fuse blowing


Is this a manual, or automatic? Manual, you may need to replace a driveaxle(or both). If automatic, check fluid, and linkage. If fluid is low, or empty, fix leaks, and fill with fluid. Have a diagnostics done on car for transmission codes. If manual, and driveaxles checkout to be okay, check any sensors on transmission. Check sensors on automatic as well; and fluid. (manaul transmission fluid is check by oil dipstick; oil lubes engine and tranny.

Apr 07, 2009 | 2000 Ford Taurus

Not finding what you are looking for?
2000 Ford Mustang Logo

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...