Question about Dodge Charger

1 Answer

How to remove upper ball joint from a arm grease cup is trashed need to replace whole thing anyway

Posted by on

Ad

1 Answer

Read your question

Need more detail

Need to know what your talking
about --like a vehicle,make, model

You either replace the entire upper
arm or you need a press that can be
used on the car

An auto parts store or dealer can answer that

If no ball joint is avail ,you buy the arm

Posted on May 29, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a rear upper control arm ball joint on a 1998 Lexus gs400


You probably should replace the whole upper control arm. I don't believe that you can separate the ball joint from the control arm without damaging it and the ball joints are not listed separately for sale. [If the ball joint is bad, the bushings can't be in very good shape, either.]
moog-rk620336-large-1.jpg
8909225.gif
To replace the upper control arm, you need to take the weight off the spring and pop the ball joint out of the spindle with a special tool
OTC 6297 Ball Joint Separator
Then it is bolted in by the 2 pivot bolts [#3 in the diagram].

Feb 03, 2015 | Lexus Cars & Trucks

1 Answer

How to replace a lower ball joint on 2004 mercury mountaineer?


Remove the brake caliper by removing the two bolts that connect it to the steering knuckle. Remove the lower ball joint cotter pin and retaining nut. Pry the steering knuckle up and away from the lower ball joint. Unscrew the grease fitting from the bottom of the lower control arm. Press the lower ball joint out of the control arm using a ball joint remover set.
Press the lower ball joint into the control arm using a ball joint installation tool. Remove the block of wood supporting the upper control arm. Install a new cotter pin through the ball joint stud.Install the grease fitting on the bottom of the ball joint. Use a c-clamp to push the piston back into the brake caliper. Reinstall the wheel assembly. Here you can find the quality parts http://www.buyautoparts.com/steering_system.htm

Aug 29, 2011 | Mercury Mountaineer Cars & Trucks

1 Answer

Need pictures and procedure 91 Ford pickup F250 twin I beam ball joint replacement.


Wheel Spindle, F-150, F-250, F-350
Removal
  1. Raise the front of the vehicle and install safety stands.
  1. Remove the wheel and tire assembly. Refer to Section 04-04 .
  1. Remove the disc brake caliper (2B120) from the rotor and wire it out of the way. Refer to Section 06-03 .
  1. Remove the dust cap, cotter pin, nut retainer, nut, washer and front wheel bearing (1216).
  1. Remove the rotor from the front wheel spindle (3105).





    Item Part Number Description 1 606085 Clamp Bolt 2 3B404 Camber Adjuster 3 800895 Nut 4 800937 Nut 5 3049 Front Suspension Upper Ball Joint 6 3050 Front Suspension Lower Arm Ball Joint 7 3105 Front Wheel Spindle 8 642569 Cotter Pin 9 3304 Steering Sector Shaft Arm Drag Link 10 383489 Nut 11 3001 Front Axle Assembly 12 388727 Bolt A - Tighten to 77-103 Nm
    (57-75 Lb-Ft) B - Tighten to 68-92 Nm
    (50-67 Lb-Ft) C - Tighten to 113-153 Nm (83-112 Lb-Ft) D - Tighten to 340-460 Nm (250-339 Lb-Ft)
  1. Remove bearing cone and roller (1201) and wheel hub grease seal (1190). Discard the seal.
  1. Remove front disc brake rotor shield (2K004). Refer to Section 06-03 .
  1. Disconnect the steering linkage from the integral front wheel spindle and spindle arm by removing the cotter pin and nut and then removing the front wheel spindle tie rod from the spindle arm with Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Remove the cotter pin and castellated nut from the lower ball joint stud.
  1. Remove the nut from the axle clamp bolt and remove the bolt from the axle.
  1. Remove the camber adjuster from the upper ball joint stud and axle beam. If required, use Ball Joint Removing Tool D81T-3010-B or equivalent to remove adjuster.
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use a pickle fork to separate the ball joint from the axle as this will damage the seal and the ball joint socket.
    Strike the inside area of the axle as shown to pop lower ball joints loose from the axle beam.
  1. Remove the front wheel spindle and ball joint from the axle.






Ball Joint, F-150, F-250, F-350 SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number U-Joint Tool T74P-4635-C Ball Joint Remover T94T-3010-AH
Removal
  1. Remove the front wheel spindle (3105) and ball joint assembly from the axle. Refer to Wheel Spindle, F-150, F-250, F-350 in the Removal and Installation portion of this section.
  1. NOTE: Lower ball joint must be removed first.

    Install the front wheel spindle in a vise and remove the snap ring from the lower ball joint.
  1. Remove the lower ball joint from the front wheel spindle using U-Joint Tool T74P-4635-C and Receiver Cup D81T-3010-A5 or equivalent for F-150. Use Ball Joint Remover T94T-3010-AH for F-250 and F-350.
  1. Turn the forcing screw clockwise until the ball joint is removed from the front wheel spindle.
  2. CAUTION: Do not heat the ball joint or the front wheel spindle to aid in removal.
    Assemble U-joint tool and cup on the upper ball joint, and turn forcing screw clockwise until ball joint is removed from the front wheel spindle.


    Installation
    1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not heat the ball joint or axle to aid in installation.
      NOTE: Upper ball joint must be installed into the front wheel spindle first.

      NOTE: Individual ball joint tools are included in Ball Joint Adapter Set D81T-3010-A or equivalent.

      To install the upper ball joint, assemble C-frame assembly, Ball Joint Receiver Cup D81T-3010-A5 and Installation Cup D81T-3010-A1 and D81T-3010-A3 or equivalents inside cup D81T-3010-A4 or equivalent in position on the front wheel spindle.
    1. Turn forcing screw clockwise until ball joint is seated.



    2. snorkelbobby_49.gif

Mar 25, 2011 | Ford F-250 Cars & Trucks

1 Answer

Ball joint repair and how do you do it


To perform the following procedure, the lower control arm must be removed from the vehicle. Refer to Removal And Installation for that procedure.

  1. Using a screw driver or other suitable tool, pry the seal boot off of the ball joint assembly
  2. Position receiving cup, Special Tool 6758 to support lower control arm when removing ball joint assembly. Install Remover, Special Tool 6919 on the top of the ball joint assembly.
  3. Using the arbor press, press the ball joint assembly completely out of the lower control arm.

NOTE: When installing ball joint in lower control arm, position the ball joint in control arm so notch in ball joint stud is in the direction shown. This will ease assembly of the ball joint to the steering when installing pinch bolt.

  1. By hand, position ball joint into ball joint bore of lower control arm. Be sure ball joint is not cocked in the bore of the control arm, this will cause the ball joint to bind when being pressed into control arm.

 

  1. Position control arm with installed ball joint, in an arbor press with Receiving Cup, Special Tool 6758 supporting the lower control arm. Then center Installer, Special Tool 6908-4 on the bottom of the ball joint
  2. Carefully align all pieces. Then press the ball joint into the lower control arm until it is completely seated against surface of lower control arm. The ball joint is correctly installed when there is no gap between the ball joint and the lower control arm. Do not apply excessive force against the ball joint or the lower control arm.
  3. Install a NEW seal boot by hand as far as possible on the ball joint. Installation of the seal boot is to be with the shield positioned as shown.

CAUTION: Do not use an arbor press to install the sealing boot on the ball joint. Damage to the sealing boot will occur if excessive pressure is applied to the sealing boot when it is being installed.

  1. Place Installer, Special Tool 6758 over seal boot and squarely align it with bottom edge of seal boot. Apply hand pressure to Special Tool 6758 until seal boot is pressed squarely against top surface of lower control arm.

CAUTION: A replacement ball joint is not pre-lubricated. Properly lubricate the replacement ball joint using Mopar Multi-Mile grease or an equivalent. Lubricate ball joint after seal boot is installed but prior to top of seal boot being pushed down below notch in ball joint stud. Air must vent out of the seal boot at notch when grease is pumped into ball joint, failure to do so will balloon and damage seal boot. Do not over grease the ball joint, this will prevent the seal boot from pushing down on the stud of the ball joint.

CAUTION: After the ball joint is properly greased, clip the end of the grease fleeing off below the hex. The ball joint seal boot is non-purgeable and further greasing is not required and can result in damage to the seal boot.

  1. Reinstall lower control arm on vehicle.

Mar 07, 2011 | 2000 Dodge Caravan

1 Answer

Can you show me detail pictures of step by step repair of ball joint and controll arm of 1990 ford thunderbird v6 3.1 automatc


prev.gif next.gif REMOVAL AND INSTALLATION Upper ball joints are not replaceable. The upper ball joint is part of the upper control arm bushing joint and is not serviced separately. If the upper ball joints are found to be defective, the entire upper control arm bushing joint assembly must be replaced. Lower Ball Joint INSPECTION
  1. Support the vehicle in normal driving position with ball joints loaded.
  2. Wipe the grease fitting and checking surface, so they are free of dirt and grease. The checking surface is the round boss into which the grease fitting is threaded.
  3. The checking surface should project outside the cover. If the checking surface is inside the cover, replace the lower arm assembly. prev.gif next.gif

Aug 26, 2010 | 1990 Ford Thunderbird

1 Answer

How to remove upper and lower ball joins on a 4x4 bronco full size 1986


For Lower & Upper Ball Joint Step by Step :

For That you use a C-clamp style ball joint press to remove the ball joint from the suspension arm-note the location of the receiver cup ! For installation of the ball-joint, use the same tool when pressing the ball joint into the suspension arm-again, note the location of the receiver cup.

Step by Step :

  1. Raise and support the vehicle safely, with jackstands.
  2. Remove the spindle and the ball joint assembly from the vehicle.
  3. Remove the snapring from the ball joint. Using a ball joint removal tool, remove the ball joint from the spindle. Do not heat the ball joint or the axle to aid in removal.
  4. Installation is the reverse of the removal procedure. Torque the ball joint stud nut to 85-110 ft. lbs. for 1983-89 Ranger and Bronco II.

    Please Rate, Thank you !

Aug 13, 2010 | 1994 Ford Bronco

2 Answers

I have a squeeking noise in the front on both sides i was told it was the controll arms needign to be replaced do we need to do the ball joints as well or do they come with both when replacing


you can either buy bottom suspension arms with the ball koint atached or just replace the ball joints.

If the suspension arms are shot, then you should be able to feel this when driving over cats eyes in the road. when the wheels contact the cats eyes they wonder, the steering wil feel like its going both ways, not tight, kinda lose?

Ball joints dont squeek they knock! most times its just as cheap to get ball joints and suspension arms/control arms as one. some things dont translate that good from UK to Us the parts have different names here, but thats the same part I mean. When you remove ball joints and in most cases you have to when replacing the arms, they get damaged and rarely last long after being put back in place, you may aswell pay now for one lot of labour than pay twice.

Hope this helps

Jan 14, 2010 | 2001 Dodge Stratus

2 Answers

Replace upper ball joint 2003 silverado 1500


The ball joints on both 2wd and 4wd upper are pressed in you need to remove snap ring and using a hammer pop out the old one out this is after you seperate the upper arm from the spindle. To install the new ball joint you should use a ball joint press that you can rent at most autoparts shops

Aug 09, 2009 | 2000 Chevrolet Silverado

5 Answers

I need to replace upper right ball joint, 98 honda civic


This is a pretty easy job.The way i do it is take the two 14mm bolts louse from the strut on the inner fender well,then take the 17mm bolt out of the bottom of the strut on the lower control arm this will make it drop down.Then take the 14mm bolt louse that fastens the ball joint to the spindle take a hammer and hit the upper spindle and it all will come apart.Now you will have the two bolts that holds the upper control arm in place these are 17mm bolts drop the strut down and remove the upper control arm now you can go in with the new one.Hope this helps !!!

Mar 19, 2009 | 1998 Honda Civic

4 Answers

Front upper ball joint replacement


The dealer's answer (if you are interested).......

The ball joint is pressed into the upper control arm and has a tapered stud for attachment to the steering knuckle. The ball joint stud is attached and locked into the steering knuckle using a special nut. The ball joint is a sealed-for-life type and requires no maintenance. If the ball joint is defective it will require replacement of the entire upper control arm.

Sorry.

Jun 19, 2008 | 2002 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...