Question about Chevrolet Chevy

1 Answer

I have a 400 small block but its burde out at 40 already and it has a scrach were one of the pisten gos and little rust and they told me i needed another one so they offered me one for 700 just the block can i use everthing i had in it and that my pistens are a little scrach can i still use those to

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 372 Answers

You should be able to reuse the items in a clean block. However its reccommended that you inspect every part carefully and replace and thing that questionable. Also the new block must be bored 40 over as well....

Posted on Aug 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake rotor removal, compressing the caliber pisten


Once you have the caliber off open the bleeder screw. To compress the piston I use a large C Clamp then close the bleeder screw. They also make a tool to compress the piston. either ay open the bleeder scew. I have seen people not do this and destroy there ABS system.

Dec 28, 2013 | Cars & Trucks

1 Answer

Engaging reverse gear


If WD-40 helped the problem then the bushes and linkage should be inspected for wear/adjustment and rust as the WD-40 is a temporary lubricant. Check it asap as the problem needs repair.

Nov 17, 2013 | 2010 Fiat Grande Punto

1 Answer

I have a saturn sl2 and one of the pisten shot through the block. could i get any other year saturn to replace the engine?


the 1.9 was used throughout the entire run of the sc2 and sl 2 vehicles from the early 90s through early 2000s. Some sensors and accessories may be different but the long block is the same.

Feb 22, 2011 | 1999 Saturn SL

1 Answer

Do you know how to install the power steering pump in 400 small block chevy?


POWER STEERING PUMPS FOR THE 400 AND 350 CHEVY ENGINES ARE HELD IN PLACE IN A BRACKET AND BRACE MOUTED TO THE ENGINE.CHECK AROUND ON LINE ON INTERNET LOOK UP POWER STEERING PUMP MOUNTING BRACKETS FOR 400 CHEVY ENGINE.YOU NEED THE MOUNTING BRACKET IN ORDER TO INSTALL POWER STEERING PUMP.

Feb 18, 2011 | Chevrolet El Camino Cars & Trucks

1 Answer

Floorboard is rusting in my 94 geo metro


There's not a whole lot you can do about a rusted out floorboard. If it's just rusting a little bit, you can probably get away with cleaning off the rust with steel wool or a wire brush and treating it with some naval jelly, then painting it with a good rust converting paint or underbody coating.

If it's already weakening the metal, the only solution is to weld a new piece of sheet metal in place.

Dec 31, 2010 | 1994 Geo Metro

1 Answer

Ignition barrel buggered


YOUR GOING TO HAVE TO STICK A SMALL CHISEL INTO THE KEY HOLE USED A SMALL HAMER TO KNOCK IT IN SOME, WITH VISE GRIP TURN TO THE ON POSITION, UNDER THE HOUSING WHERE THE LOCK CYLINDER GOS INTO, THERE WILL BE A LITTLE HOLE PUSH THAT LITTLE PIN IN THERE WITH A PICK HOOK AND SLIDE IGNITION LOCK OUT.

Nov 05, 2009 | 1993 Toyota Corolla

1 Answer

1995 lexus ls400 can't lock hood


Could be that the latch is already latched, or just needs a little lube (wd-40 works great) Have someone pull the hood release and look at the latch see if it moves or if it look to be closed you can ulatch it with a pen or pencil while someone pulls the hood release if that is the case.

Oct 06, 2009 | 1995 Lexus LS 400

1 Answer

1960 Chevrolet Small block engine. The key in the


just spray it a little if needed with WD-40 to help loosen then I pry it forward from behind with a good size screwdriver or similar, and it just kind of rolls out.

Aug 08, 2009 | Chevrolet Impala Cars & Trucks

2 Answers

How do i locate and change a water pump in a 1995 chevy caprice?


Well the water pump will be mounted directly to the engine block with two large hoses running from it to your radiator.

When you get the new water pump make sure it has new gaskets in there. Should only be a couple of bolts and it comes right off.

Scrape off all of the old gasket from the engine block before you put the new gasket and pump on.

Good luck!

-Captain Jake

PS - Might have to drain your radiator first, it has a little valve at the bottom. And PLEASE make sure the car is cold so your poor husband doesn't burn the **** out himself :D

Feb 13, 2009 | 1995 Chevrolet Caprice

1 Answer

Fuel Filter Changed


What happens when you remove air intake from throttle body & spray a little wd-40 in to the throttle body, and try to start? If it starts and runs temporarily, you've still got a fuel delivery problem.That coffee color worries me, like maybe your fuel lines etc are plugging up with rust etc, from inside tank. Have you added any fuel system cleaner to gas lately?

Aug 30, 2008 | 1999 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...