Question about 1998 Mercury Villager

3 Answers

Have availiable a 98 villager with water in the oil suspect water pump falure / overheat and warped head blown head gasket engine runs smooth labor to replace head gasket waterpump and true heads cost will be according to shop rates can proably pick up veh for 1000 dollarw 150000 miles on veh

Posted by on

3 Answers

I would part with it,don't repair

Too old & I wouldn't ever recommend
a van type vehicle

I made a living in the trans repair business
on them

Have not even been in one since 1998
& never will be

Not a safe vehicle in an accident ,any
van type brand

Posted on May 28, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,056 Answers

A new cylinder head cost about 350 dollars. Junkyards may sell them cheaper, but it would be used. The cylinder head maybe repairable. The labor hour for replacing a cylinder head is about at least 6 to 8 hours on the flat rate book. So if the shop charges for example 100 dollars per hour to do the job thats already 600 dollars labor at least. It is not cheap price, but it is somewhat reasonable.

Posted on May 28, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,915 Answers

$1000 plus the costs to do head gaskets, bearings (remember, antifreeze in the lubrication system means cam and crank bearings), you are talking about a rebuild, since it's out and apart you may as well do the rings too (150,000)...align boring, deck the block, heads...with the misc. items you will end up doing, you might be better off looking for a low mileage junkyard engine instead of going through that one.

Posted on May 28, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car overheating and mixing water with oil


You have blown the head gasket. Also, you may have warped the head if it's aluminum which will happen due to ignoring the issue of overheating...which eventually caused the "blown head gasket". So, it sounds like you have 2 issues to resolve. 1) Why was it tending to overheat? Stuck thermostat, water pump issue or??? 2) Repairing the cylinder head or replacing it if warped badly, if your lucky it's just a blown head gasket. Allowing a overheating vehicle to be in service without solving that the overheating can lead to MANY other expensive problems.

Feb 12, 2014 | 2006 Fiat Pininfarina

1 Answer

My neon will not start replace heads and radiator frist


Signs of a Blown Head Gasket
Note: You can only truly confirm your suspicion by actually seeing the gasket, although precursor signs are usually evident.

Input from Answers.com contributors:

If you see coolant leaking from the water pump, I would pressure-test it and pinpoint the leak and fix that first; oil seepage isn't necessarily abnormal.
Typical symptoms of a blown head gasket may include these: bubbles of air coming up into your radiator (remove cap before starting); a leaking radiator; milkshake-colored oil; overheating; rough running; coolant or oil running from head; spark plug(s) that have a green tint (if green coolant); white-colored or sweet-smelling exhaust.
White smoke from your tail pipe, or loosing coolant through your overflow. Take the cap off and rev the engine: if you see bubbles, or if it comes out, you'll know.
A blown head gasket will leave a dark smell in the radiator. And you will have high back pressure coming though your radiator cap.
Take your car to a radiator shop to have a detector installed: If the blue liquid inside a "bulb" turns yellow, you have a leak.
Beware that if you drive for too long and it overheats, a blown engine will be your outcome.
A blown head gasket can go out in different areas causing different symptoms. Do a compression test to give you some idea. Don't confuse low compression for a bad head gasket, though. A bad valve can lower compression. And a bad ring.
There are lots of clues you can look for. When in doubt and you have tried everything, have the head checked out by a well-established machine shop first, to see if the head was the problem. This way you're not wasting your time replacing the gasket.
My car once had a blown head gasket. I had a great deal of coolant loss. The engine lacked power and ran poorly. It had white smoke coming out the tail pipe. And it overheated very quickly. Also, it had water in the oil.
A quick way to check: Look at your spark plugs; if coolant squirts out, you definitely have a blown head gasket!
Low compression does not necessarily mean a blown head gasket, but it is a good indicator if there is a sharp drop in compression on one or two cylinders, with no drop in the others. Sometimes a blown head gasket will cause a whistling or wheezing sound, but not always. It will not always cause water to enter the oil - or oil to enter the water - but they are signs to look for. Overheating will almost always occur, due to the exhaust entering the coolant. Check your overflow bottle for exhaust smells. Watch for bubbles or overflow of coolant from the radiator while running the engine. Check for muddy gray-looking oil or bubbles on the dipstick.
Often (but not always), a blown head gasket will also cause deposit of water on a piece of cardboard held an inch from the tailpipe output while the engine is running (when this is happening, it is likely that the catalytic converter has been ruined and the muffler will corrode in short order as well). Sometimes drops of water will be seen dropping from the end of the tailpipe.
Another clue: Turn on the heater; often when the head gasket is blown an odor of antifreeze and synthetic rubber will emanate from the heater vents.
Many of the symptoms of a blown head gasket can be caused by some other problem in the cooling system, without the head gasket being damaged. Conversely, other problems with the cooling system can cause a blown head gasket and/or warped head. For example, a corroding radiator can send chunks of rust through the cooling system which take out the thermostat and water pump. If the thermostat is old, sticking and corroding, it can send those chunks through the system and take out the water pump or cause a blockage in the radiator, etc.
Radiator leaks can be the primary cause, or a result, of failures in other cooling system components.
Don't keep driving with the car overheated, especially if your engine has an aluminum head; you are likely to warp it. If it is warped beyond a certain tolerance, it cannot be planed and will have to be replaced when the head gasket is replaced.
One of the most common tell-tale signs is a milky-gray ring around your oil cap. When coolant enters the engine oil through a crack in the head or through a blown gasket, it evaporates and leaves a milky ring around the oil cap. Another easy way to tell is to check your oil dipstick. Change your oil and pull out the dipstick. Make sure that you take note of how far up the dipstick the oil is. Top off your cooling system and fill your cooling reservoir to the top. Screw radiator cap back on and start engine. Run engine for about 20-30 minutes or until it reaches normal operating temperature. Allow engine to cool (engine must cool completely to get accurate oil reading). Check oil dipstick again. If the oil has a watery appearance and has risen noticeably up the dipstick, then you probably have a blown head gasket or a warped head. Also, look for a sweet-smelling liquid coming out of your tailpipe. Any of the above symptoms could be the result of a blown head gasket.
The easiest way to tell is with a compression meter. This replaces the spark plug and lets you know what compression each cylinder is running at. If your compression is abnormally low, then you have a blown head gasket or a warped head. (Note: check the repair manual for appropriate compression of each cylinder.)
This can be detected in a variety of ways: One way is to note whether that part of the engine block is leaking fluid. This is difficult to determine since there are many other parts of the engine nearby that can also leak fluids, especially when a vehicle is parked in one place for more than a few hours. One of the best indications of a blown, or nearly blown, head gasket in most automobiles is when the cooling system appears to be malfunctioning. The cooling system's efficiency and performance can be directly affected by the quality of the head gasket.
If your radiator is getting low on water often, this is a sign. The water could be discharged through the tailpipe on your automobile. Another sign is if your car motor has a miss in the engine. The water could be going in on top of the cylinders. This will foul the plugs and cause it to miss.
There are a few simple indicators you can check for with the engine cold and not running: 1) contaminated oil - it will have a milky appearance from the water mixing in the oil 2) oil on the top of the coolant inside the radiator (if your vehicle has a remote header tank you may not get this); 3) Have someone crank (remove the coil lead or disable the electronic ignition) the engine on the starter with the radiator cap or coolant jacket bleed hose/bolt removed. If the coolant pulses up and down or blows bubbles, you could be in trouble. If you find any of these symptoms move on to removing the spark plugs (label the plugs and the leads as you remove them, so you can put them back in the same place) and again crank the engine on the starter. Depending on how badly your head or gasket is gone, you may get coolant or oil coming out of the plug holes. Inspection of the plugs will also reveal problems during combustion: if you have rusty flaky deposits on the plugs, you may be burning off water; and if you have a heavy carbon, you are burning oil. If you have any of the first 3 items listed (water in oil, oil in water, or pulsing coolant - but don't get any result from checking the plugs) change the oil and water as appropriate, then warm up the engine without the radiator cap on (or the bleeder hose/bolt) and watch for bubbles as the engine warms up. Put the cap back on the cooling system and take the vehicle for a short drive, or run the engine till the entire system is up to temperature and then check the oil for contamination. Having these symptoms is not always indicative of a blown head gasket; usually if the gasket is gone, there is going to be some warping of the head and or block of the engine.
Loss of engine coolant with no external leaks, a continuous stream of bubbles can be seen with the radiator cap off, black gummy and sometimes crusty stuff around the radiator


Several common signs of a blown head gasket:

Blue/white smoke coming out the tail pipe which indicates oil is burning
Dripping oil from the gasket itself
Carbon Monoxide or hydrocarbons in the cooling reservoir
Excessive coolant loss with no obvious source of leakage
Loss of power or a rough engine due to compression loss
Water mixing with oil
Oil mixing with water
Low compression in 2 or more adjacent cylinders
Remove dipstick and let a drop of fluid fall on hot part of engine - oil will smoke water will "sizzle"

Jul 29, 2012 | 2004 Dodge Neon

1 Answer

How would i know if my overheating problem in my 97 Geo Metro Prizm is a radiator, water pump, blown head gasket, cracked head or a thermostat problem. is there some way i can check for this?


Oil and coolant mixed usually means the engine is damaged.
Blown head gasket, or cracked block - head.
You may have coolant in the engine oil too.
I would not drive it.

Jul 25, 2012 | 1997 Geo Prizm

1 Answer

1998 sl1 oil in water running hot


If you have oil in your coolant then your head gasket is blown. Be careful, and don't let it fully overheat because you will warp your head and have to buy an entire engine.

Mar 20, 2011 | 1993 Saturn SC1

1 Answer

How to dertimine if car has a blown gasket Car overheats after a couple of miles, have added a bottle of some kind of fluid to radiator with no help


Durango with the 4.7 are notorious for blwn head gaskets, check the engine oil for overfill or water, check the tailpipe for white smoke or steam, check the coolant for oil or an exhaust smell. If you have a compression checker, use that to determine if you have a balance in compression on all cylinders. If it overheats, and runs smooth check all the cooling system components such as the thermostat, coolant level, water pump and fan/ fan clutch if so equiped. Fan relay can also be in the picture.

Jul 24, 2010 | 2001 Dodge Durango

1 Answer

28 Solutions for ''HOw can I tell if I have a cracked head blown head gasket or cracked blown like how can I see it''


Often (but not always), a blown head gasket will also cause deposit of water on a piece of cardboard held an inch from the tailpipe output while the engine is running (when this is happening, it is likely that the catalytic converter has been ruined and the muffler will corrode in short order as well).

Sometimes drops of water will be seen dropping from the end of the tailpipe. Another clue: turn on the heater; often when the head gasket is blown an odor of antifreeze and synthetic rubber will emanate from the heater vents.
Many of the symptoms of blown head gasket can be caused by some other problem in the cooling system, without the head gasket being damaged. Conversely, other problems with the cooling system can cause a blown head gasket and/or warped head.

When checking for a blown head gasket, one of the most common tell-tale signs is a milky-gray ring around your oil cap. When coolant enters the engine oil through a crack in the head or through a blown gasket, it evaporates and leaves a milky ring around the oil cap. Another easy way to tell is to check your oil dipstick. Change your oil and pull out the dipstick. Make sure that you take note of how far up the dipstick the oil is. Top off your cooling system and fill your cooling reservoir to the top. Screw radiator cap back on and start engine. Run engine for about 20-30 mins. or until it reaches normal operating temperature. Allow engine to cool (engine must cool completely to get accurate oil reading!!). Check oil dipstick again. If the oil has a watery appearance and has risen noticeably up the dipstick, the you probably have a blown head gasket or a warped head. Also look for a dripping, sweet-smelling liquid coming out of your tailpipe. Any of the above symptoms could be the result of a blown head gasket. The easiest way to tell is with a compression meter. This replaces the spark plug and lets you know what compression each cylinder is running at. If your compression is abnormally low, then you have a blown head gasket or a warped head. (note: consult repair manual for appropriate compression of each cylinder.)

Dec 12, 2009 | 2005 Dodge Grand Caravan

3 Answers

Nissan Sentra GA14 engine - Water in Engine Oil


If the engine has been flushed well including the radiator and you are still getting water in the oil. The culprit is the cylinder head or the block has a crack internally allowing water into the oil.

Oct 10, 2009 | 1997 Chevrolet Monte Carlo

1 Answer

Water shoots out of expansion tank and overheats, electric fan no


If your oil is milky it is a blown head gasket or worse a warped head.

Apr 15, 2009 | 1999 Volkswagen Golf

1 Answer

Water in oil


I have yet to see a cracked head on a 22R,so more than likely a blown head gasket,unless you overheated and warped the head and worst case a hole between the cylinder wall and water jacket(this is pretty rare).The only way to tell short of using some expensive tools or taking to your local shop is to pull the head and inspect the gasket for leakage wich is generally fairly obvious(separation of the gasket layers,oil and water between water and oil passages)and checking the head deck for warpage.If there is obvious leakage in the gasket you're looking at a top end gasket set if the head is slightly warped you can get away with a thick graphite head gasket,I personally use these as they are very forgiving on slightly warped and scratched head decks and inepensive also,but a severly warped head will require milling at a machine shop or replacement.

Apr 04, 2009 | 1987 Toyota Pickup

Not finding what you are looking for?
1998 Mercury Villager Logo

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...