Question about Pontiac Grand Am

1 Answer

I need to know where the crakshaft sensor is on a 97 grand am with a 2.4

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Pontiac Master
  • 8,206 Answers

Just above the oil filter. Thanks for using Fixya.

i need to know where - jturcotte_1774.gif

Posted on May 28, 2011

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Crankshaft sensor and camshaft sensors

depends on the year and model. for example, on my 97 Grand Cherokee Laredo 4.0L , the cam sensor ( also called pick up relay or coil ) is underneath the distributor cap and rotor. flat, round, plastic device with a magnet and little wire (2) with plastic connector. the crank sensor is on the top left ( driver side ) , backside of the bell housing of the transmission. easy to find if looking up at transmission from underneath jeep. wire harness runs by it. will need a couple of long handled extension bars to remove bolt holding it in. do not forget to put little gold bracket back on with new part. this acts as a spacer as well as for support. you can look up more specific info for your vehicle on just type in for example : signs of a bad cam sensor on what year vehicle, how to change the part on vehicle etc.

Dec 07, 2013 | 1996 Jeep Grand Cherokee

1 Answer

Why doesn't the car get power to crakshaft position sensor

Because the sensor is an output sensor

It generates an AC Signal, it does not receive
battery voltage & it only works when the motor
is turning over

Google what one is & read up

Aug 31, 2013 | 1999 Isuzu Rodeo

1 Answer

2001 montana crankshaft sensors test

You would use a low voltage test light or analog meter depending on what you are testing for. The sensor generates a reference pulse.

Aug 15, 2012 | 2001 Pontiac Montana

1 Answer

Location of coolant sensor for 97 Jeep Grand Cherokee v8

in the 5.2L V8 engine the coolant sensor is located on top of the engine. Locate the coolant thick hose coming from top of the ratiator to the top of the engine. Look at the place such hose connects to the engine you wont miss the sensor it is about one inch from there.

Jun 27, 2010 | 1997 Jeep Grand Cherokee

2 Answers

'97 Grand Marquis needs a new Oxygen Sensor

this is going to be on the left side of the exhaust second sensor back or if you only have two sensors it will be just after the cat. all you need is a 7/8 wrench. to change it unless you have the o2 sensor socket.

Mar 01, 2010 | Mercury Grand Marquis Cars & Trucks

1 Answer


You need a new speed sensor put in the transmission housing or the plug to it has faulty wire ends.If the sensor is leaking oil the you need one for sure,if the plug is wet with oil when you pull it out then replace the sensor.

Jan 14, 2010 | 2005 Pontiac Grand Prix

1 Answer

97 grand am 2.4 motor in a 99 cavalier z24

As long as you can get it bolted to the engine somewhere it should work OK. I hope thats all the difference between those 2 engines. ?????

Nov 19, 2009 | 1999 Chevrolet Cavalier

2 Answers

02 sensor

First of all if it is a 6 cylinder its an inline engine (4.0L). The reason I bring this up is it changes your O2 sensor configuration. Bank 1 sensor 1 ( there is only one bank because only 1 manifold) is the primary O2 sensor controlling the air/fuel ratio dependant on other sensors. Bank 1 sensor 2 is After the cataylistic converter. Depending on the code if low input or high input could be wiring and not a sensor at all. Also a low flow or high flow could indicate somebody previously "punched" the converter out or it is getting clogged due to age and mileage. Hope this helps.

Sep 14, 2008 | 1997 Jeep Grand Cherokee

1 Answer

O2 sensors

I don't have pictures, but if you look under the car, find the exhaust system, and specifically the catalytic converters (they should be under the center of the car, most likely about in line with the rear seat). Since your car is a 97, it's got OBD2 emissions compliance, which means you'll have an O2 sensor in front of each cat as well as behind each one. They'll be small cylinders sticking up and out of the pipes about 2 inches, with wires coming off the ends. The forward ones are between the front edge of the cat and the engine, and the rear ones will be just past the cats. They're the only electrical sensors that should be on your exhaust system, so you should be able to pick them out easily enough once you're under there.

Jul 30, 2008 | 1997 Pontiac Grand Am

2 Answers

Oxygen sensor wiring diagram

My 97 cherokee catalytic converter was stolen, oxygen sensor wires cut. the replacement is black, grey and white. the jeepicon1.png is different color. i need help knowing which wires get connected to which.

Jun 24, 2008 | 1997 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides