Question about Isuzu Rodeo

Open Question

Need torque settings for petrol holden rodeo 6VD1 engine automatic 1999

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
stevenhurc
  • 450 Answers

SOURCE: torque settings for a holden rodeo 3.5 ra. Head

stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)
do not reuse head bolts or apply any lubricant to the bolts. Do up bolts in following order for each head.
6 1 3 7
front
5 2 4 8

Posted on Dec 05, 2009

Ad
dungeonfleet
  • 46 Answers

SOURCE: Head bolt torque settings...

Stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)

Buy new bolts first tho

Posted on Jan 16, 2010

dcramer531
  • 1654 Answers

SOURCE: I need the torque settings for the cylinder head

http://www.autozmagz.com/isuzu/2000-isuzu-trooper-s-torque-specifications/
try here and see if they can help. You can download manuals for free here.

Posted on Nov 23, 2010

snownbird33
  • 120 Answers

SOURCE: Holden 94 rodeo petrol

Good Day
Vale clearance cold
intake .006 in (.15 mm)
exhaust .010 in (.25 mm)

Timing
1. With transmission in Neutral or park, start engine and warm to normal operating temp. turn eng,and all accessories off. connect Tachometer. Connect timing light to no 1 spark plug wire.

2. Disconnect and plug fuel vapor canister purge hose and EGR vacuum hose. Start and ensure idle is 900 RPM. adjust idle as required. Check ignition timing ( 12 @ 900)

3. If adjustment is required, loosen distributor hold down bolt and turn until timing is within specification. Tighten distributor hold down bolt and recheck timing. adjust idle speed as required.

hope this helps

Cheers

Posted on Sep 30, 2008

stevenhurc
  • 450 Answers

SOURCE: looking for torque settings for Holden rodeo 1999

big ends 54Nm/40Ft-lbs
mains 39Nm/29Ft-lbs and mains side bolts are same torque

Posted on Jun 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can a petrol gear box go into a diesel engine 4wd Holden rodeo RA


if manual transmission , no problem
if automatic transmission , torque converter different

Jul 10, 2017 | Holden Cars & Trucks

1 Answer

Head bolt torque settings and order for 24litre petrol engine Austalia Holden rodeo Isuzu motor c24se Holden Rodeo 2003


this is USA forum
not a single HOLDEN here
not a one.
why ask us,
why not join , real forum that covers your country

http://www.planetisuzoo.com/

Mar 12, 2017 | Isuzu Cars & Trucks

1 Answer

Is it possible to fit a manual gear box to an automatic 1996 2.6 petrol holden rodeo?


You should be good as long as you replace the flywheel on the automatic engine with the one from the manual. You may also have to replace some sensors once you get it up and running because a manual will drive different that the auto and your pollution control will likely act up by turning on codes.

Sep 01, 2014 | Cars & Trucks

1 Answer

Rodeo petrol starts but wont rev


Holden Rodeo 1989 2.6mpi , start and only runs for 2 or so seconds themselves stalls, after putting on a fuel peesure gauge, fuel looked okay and slowly dropping, found the ECM relay was intermittently switching on and off, gave it a tap and the engine kept on running, relay not repairable, replace with new part. Located in the fuse and relay box on the right hand side of engine bay next to battery. Hope this helps.

May 24, 2012 | Holden Rodeo Cars & Trucks

1 Answer

Where is the location of camshaft sensor 1998 isuzu trooper


if its diesel 4JX1 its in top cam belt cover cant miss it, sensor is very clearly visible.
if its petrol V6 (6VD1 or 6VE1) its in left head at rear behind inlet manifold
these pictures are for petrol V6, Jackaroo(Trooper) and Holden Rodeo are the same.

stevenhurc_21.jpg



stevenhurc_22.jpg

Apr 10, 2011 | 1998 Isuzu Trooper

2 Answers

Hi, i am looking for a isuzu dmax (holden rodeo) 2004 shop manual and parts catalog preferably on CD; engine is a 4HJ1 (orlando at orlando.mah@gmail.com)


this was from 2007 Australia, you can purchase CD from dealers spare parts outlets for workshop manual all light commercial vehicles are covered, infomedia do CD
LCRV SMI Version 2, part no: 92148175 ___ $A320.00
they still do this here

Jul 12, 2009 | 2004 Isuzu Rodeo

2 Answers

Head bolt torque settings...


Stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)

Buy new bolts first tho

Jun 28, 2009 | 2001 Isuzu Rodeo

1 Answer

Head bolt torque settings


Stage 1 = 29Nm(21 lb ft/3.0 kg-m)
final = 64Nm(47 lb ft/6.5kg-m)

Buy new bolts first tho

Jun 27, 2009 | 2001 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

547 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...