Question about 1999 Chevrolet Silverado 1500

1 Answer

Oil pressure sending unit location? - 1999 Chevrolet Silverado 1500

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 338 Answers

Drivers side of block under exhaust manifold-just behind engine mount

Posted on May 28, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Lwhere is oil pressure sending unit on 2006 dakota v6 located?


Location of the OPS unit is at the rear of engine near the distributor. (OPS) oil pressure sending

Jul 11, 2014 | 2004 Dodge Stratus

1 Answer

I need to replace the oil sender switch on my 2002 Buick La Sabre


first need to buy oil pressure sending unit 3/8 deep socket remove oil pressure sending unit you need teflon tap sealer for oil sending unit threads.okay to replace oil pressure sending unit.you need safe raise support vechicle locate oil pressure sending unit next to the oil filter.disconnect oil pressure sending unit wire connector then use oil pressure sending unit 3/8 socket remove the sending unit.then take new oil pressure sending unit use teflon tape white plumbers tape or use thread sealer apply to the oil pressure sending unit threads then install new oil pressure sending unit and reconnect electrical connector to sending unit.then crank engine check for oil leak if all is good lower vechicle back to ground wait several minutes check engine oil level.you good to roll.

Feb 09, 2013 | 2002 Buick LeSabre

1 Answer

Where is the oil pressure sending unit located on a 1999 oldsmobile alero


2.2L ENGINE OIL SENDING UNIT LOCATED FRONT CAMSHAFT HOUSING ON LEFT DRIVER SIDE OF ENGINE.FOR 3.1L ENGINE OIL PRESSURE SENDING UNIT LOCATED NEXT TO OIL FILTER.

Sep 16, 2011 | 1999 Oldsmobile Alero

1 Answer

Where is the oil sending unit located on a 2002 chevrolet malibu


V6 ENGINE OIL PRESSURE SENDING UNIT LOCATION NEXT TO OIL FILTER. THE 4 CYLINDER ENGINE OIL PRESSURE SENDING UNIT LOCATION IS FRONT CAMSHAFT HOUSING ON THE LEFT DRIVER SIDE OF THE ENGINE COMPARTMENT.

Mar 20, 2011 | 2002 Chevrolet Malibu

1 Answer

Where is the oil pressure sending unit?


The oil pressure sending unit is located on the engine block, passenger side by the Distributor. Good luck and make sure you get the right sending unit, there is the simple unit that only turns on a low oil pressure light and the other will send signals to the oil pressure gauge.

Feb 06, 2010 | 1996 GMC Suburban

2 Answers

Oil pressure sending unit


On all 2.0L and 2.4L engines, the oil pressure sending unit switch is located on the engine block, below the exhaust manifold, on the firewall side. On all 2.5L engines, the oil pressure sending unit switch is located on the engine block, below the front exhaust manifold on the radiator side.

May 24, 2009 | 1996 Plymouth Breeze

3 Answers

Where is the oil pressure sending unit located?


The pressure sending unit is located on the passenger side rear of the engine just above and slightly to the left of the filter and filter housing.

May 10, 2009 | 2000 Buick LeSabre

1 Answer

Oil pressure sending unit location


oil pressure sending unit show location on 2000 dodge caravan V-6

Mar 23, 2009 | 1997 Dodge Stratus

2 Answers

Pontiac Bonneville(2000) oil pressure sending unit


The oil pressure sending unit is located behind the oil filter, Threaded into an aluminunm housing. It has wiring that plugs into the sending unit. The oil filter has to be removed and you will need a deep well socket and a 6 inch extension. Change the oil and the sending unit together.

Jan 24, 2009 | 2000 Pontiac Bonneville

5 Answers

Where is the oil pressure sending unit on 2004 dodge stratus?


per the Haynes manual for the 95-05 Dodge Stratus on the 2.0L & 2.4L DOHC 4 cyl engines, the oil pressure sending unit is located at the left end of the rear side of the block. On 2.4L SOHC 4 cyl engines, the sending unit is located at the left end of the rear side of the block. On 2.5L & 3.0L V6 engines, the sending unit is located on the oil filter housing, on the front side of the block. On 2.7L V6 engines, the sending unit is located at the left end of the rear side of the block. To access it, remove the heat shield.

Jan 23, 2009 | 2004 Dodge Stratus

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...