Question about Mercedes-Benz SLK

Open Question

Got an OBD error code P0715 (failed speed sensor) on my 2001 SLK230. Where is the speed sensor located?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: transmission input speed sensor location

It is located on the front of the transmission. you will see 2 of them one on the left under small transmission lines it is the input then to the right behind the radiator overflow there is the other one. Easiest way to change them is with a 1" deep well socket

Posted on Jun 02, 2009

  • 1071 Answers

SOURCE: 2001 Hyundai XG300 with an engine light (p0715/P1159)

clean up all ground wires but you may need both of those items

Posted on Jul 21, 2009

  • 1 Answer

SOURCE: I have a code p0715, which is the input turbine speed sensor

Have the same problem with the input speed sensor. The part, so far, is only made by Mitsubishi (Part No. 8651A111) and cost about $110 (w/ tax in TX).

Posted on Oct 07, 2009

dmfixit
  • 226 Answers

SOURCE: computer error codes P0705, p0715, and p0720 on a

transmission range sensor / check the wires are ok by the trans selector .might need a new sensor to .

Posted on Feb 04, 2010

  • 162 Answers

SOURCE: how do I locate the turbine speed sensor on a ford

its on the front of the transmission below the coil it compares the input shaft/turbine speed against the speed of the output sensor it is checking to see how much slip or diffrenece in shaft speeds the only time the two shafts are spinning at the same time is when torque converter is in lockup

get this sensor from ford dealer for a little more than $100 bucks

Part number F32Z7F040A

Posted on Apr 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1998 dodge caravan 3.3L fault codes p0500 p0700 p0720 p0715, how do I repair and replace sensors to pass smog test


Follow the links for each fault code.
http://www.obd-codes.com/p0500
P0700 Transmission Control System Malfunction
P0720 Output Speed Sensor Circuit Malfunction
P0715 sets when there is an error in the transmission's input speed sensor signal. On the front of the trans there is an input and output speed sensor that the trans controller looks at for shifting control.

While the code could have set because of a wiring or connection problem, it's almost surely the sensor. Input speed sensor failures are not uncommon.

The input speed sensor is mounted right on the front of the trans directly under where the cooler lines attach. It threads directly in and has a 1" hex for a socket for removal. If the wiring and connection look visibly ok then I would recommend replacing the sensor

Jul 06, 2016 | Dodge Cars & Trucks

1 Answer

I have a 2001 Mitsubishi montero sport xls model. My check engine light is on and I have a code number of P0715...does anyone know what that code means?


The code indicates the Input Turbine shaft speed sensor is giving an erratic signal or there may be a mechanical transmission issue. I would go with a new sensor. Try rockauto.com to purchase a new sensor, much cheaper than the dealer. Also see sketch of location of the sensor on the tranny.

25495758-jxuyvqlutvovh3pi1e50k1yy-1-0_0.png

Feb 28, 2015 | 2001 Mitsubishi Montero Sport XLS

1 Answer

Whats ford windstar error codes p0715 mean


I hope this helps and is what your looking for... good luck

http://www.fordobdcode.com/p0715-ford

Ford P0715 OBD-II Trouble Code Definition:
P0715 Input Shaft Speed Sensor Circuit Malfunction
P0715 Ford OBD-II Trouble CodeDescription:
OBD Trouble Code P0715 Input/Turbine Speed Sensor "A" Circuit What does the code mean? OBD-ii Code P0715 definition:
The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM). Symptoms Sumptoms of OBD code P0715
- Engine Light ON (or Service Engine Soon Warning Light) - Possible shifting problems Causes Causes of the OBD-II code P0715
- Transmission speed sensor circuit is open or shorted. - Poor transmission speed sensor circuit connection - Faulty transmission speed sensor The Error code is generally activated on detection of the following conditions: Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the sensor. Solutions

Jun 22, 2014 | 1999 Ford Windstar

1 Answer

2001 Dodge Stratus with error codes P0715 and P0700.


speed sensor and transmission control, change the speed sensor and have the codes erased, drive for a while and see if the light comes back.

Sep 05, 2012 | 2001 Dodge Stratus

2 Answers

P0715 turbine input shaft speed sensor circuit what that mean


P0715 MAZDA - Input Turbine Speed Sensor Circuit Malfunction.


xicon.jpghttp://engine-codes.com/p0715_mazda.htmlForum CodePossible causes- Transmission speed sensor circuit is open or shorted.
- Poor transmission speed sensor circuit connection
- Faulty transmission speed sensor When is the code detected?Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the sensor.

Jul 04, 2012 | 2001 Mazda Tribute

1 Answer

I am getting both PO715 and PO751 error codes on my 2000 grand caravan. Does this mean the tranmission needs to be rebuilt?


P0751 Shift Solenoid A Performance or Stuck Off (generic OBD description)
P0715 Input/Turbine Speed Sensor Circuit Malfunction

The service manual does not list P0751 as a valid code for your vehicle. You may want to re-check it to make sure you are reading it correctly. Also note that many generic OBD code readers cannot give complete renderings of "manufacturer-specific" codes. You may be getting this code if you are using a generic OBD code reader because there is a manufacturer-specific code present and P0751 is the closest "generic" rendering of the code that the code reader could find.

P0715 is a CIRCUIT malfunction. NO, this does not mean that your transmission needs to be overhauled. This means that either the turbine speed sensor has an electrical failure in itself or the circuits between the turbine speed sensor and the computer are defective. Electrical diagnosis needs to be done.

Please note that BOTH of these codes can be cause by low battery voltage and attempts to diagnose the circuits involved should only be done AFTER verifying that the battery and charging system is working properly.

Jul 31, 2011 | 2000 Dodge Grand Caravan

1 Answer

WHAT IS CODE P0715 ON A 2001 LEXUS GS300


P0715 Input/Turbine Speed Sensor Circuit Malfunction

It seems that you may have a problem with your sensor on or in your transmission.

Jun 03, 2010 | 2001 Lexus Gs 300

1 Answer

Check engine light with following codes p 1529 p0720 p0715


P1529 indicates that your TCM asked the ECM to turn on the check engine lamp.

The range switch and the output speed sensors are the items that are abnormally affecting the operation of the transmission. The diagnostic logic in your computer can distinguish these issues from one another, so you'll definitely want to do both. You have no diagnostic code for the input speed sensor (P0715) listed, so I have made no recommendation to replace it. In my opinion, it's not a labor-intensive repair, so I wouldn't recommend replacing it unless you have reason to believe it's bad.

DTC - P0720 (OUTPUT SHAFT SPEED SENSOR SYSTEM)
Code No. P0720 Output shaft speed sensor system
If the output from the output shaft speed sensor is continuously 50% lower than the vehicle speed for 1 second or more while driving in 3rd or 4th gear at a speed of 30 km/h or more, it is judged to be an open circuit or short-circuit in the output shaft speed sensor and diagnostic trouble code No. P0720 is output. If diagnostic trouble code No. P0720 is output four times, the transmission is locked into 3rd gear or 2rid gear as a fail-safe measure.
Probable cause
Malfunction of the output shaft speed sensor
Malfunction of the transfer drive gear or driven gear
Malfunction of connector
Malfunction of the TCM

DTC - P0715 (INPUT SHAFT SPEED SENSOR SYSTEM)
Code No. P0715 input shaft speed sensor system
If no output pulse is detected from the input shaft speed sensor for 1 second or more while driving in 3rd or 4th gear at a speed of 30 km/h (19 mph) or more, it is judged to be an open circuit or short-circuit in the input shaft speed sensor and diagnostic trouble code No. P0715 is output. If diagnostic trouble code P0715 is output four times, the transaxle is locked into 3rd gear or 2nd gear as a fail-safe measure.
Probable cause
Malfunction of the input shaft speed sensor
Malfunction of the underdrive clutch retainer
Malfunction of connector
Malfunction of the TCM

Is needed replace.

Nov 04, 2009 | 2001 Hyundai Elantra

2 Answers

Help


P0715 Input/Turbine Speed Sensor Circuit Malfunction U are going to have to pull the pan off the transmission and check/replace the input shaft turbine speed sensor.

May 27, 2009 | 2001 Lexus Gs 300

1 Answer

Santa Fe Code p1529


I am sorry the above codes is general error code , the error your getting is car specific hence the codes where not there in the list:

P0715
Input speed sensor system

If no output pulse is detected from the input shaft speed (PG-A) sensor for 1 second or more while driving in 3rd or 4th gear at a speed of 30 km/h or more, it is judged to be an open or short circuit . In the input shaft speed sensor and diagnosis code P0715 is output. If diagnosis code P0715 is output four times, the transmission is locked into 3rd gear (D range) or 2nd gear as a fail-safe measure

P1529
TCM MIL request signal, this code sets in the computer engine control module when there is a transmission fault code

Jul 08, 2008 | 2001 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...